User manual

Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position (0 ~ 360 .
2).Tighten No.3 adjusting screw.
3).Loosen the No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0° ~ 360°).
6).Tighten No.1 adjusting screw.
° °)
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
Steps:
1.Drill the screws holes and the cable hole on the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt
into the screw holes.
Figure 2-8 Fix the Camera to the Ceiling
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-9 3-axis Adjustment
6.Adjust the zoom and the focus.
1).Output the image to the monitor.
2).Push forward to remove the adjusting sheet
located on the bottom of the camera. See
figure below.
3).Insert the removed adjusting sheet to zoom
slot and focus slot to adjust the zoom and the
focus.
4).Put the adjusting sheet back after the
adjustment is done.
2.4 Power Supply
Figure 2-11 The Powe Cable & the Video Cable
Note:
Please make sure that the power adapter is
compatible with the camera, and the standard
power supply is 12V DC. Please refer to the
technical specification for more information.
Figure 2-7 Drill Template
Figure 2-1 Drill Template
Figure 2-4 Drill Template
Figure 2-5 Fix the Camera to the Wall
Figure 2-6 3-axis Adjustment
Figure 2-10 Focus and Zoom Adjustment
Figure 2-3 3-axis Adjustment
90°
360°
360°
3
2
1
2
1
Ceiling Mounting
2
2
2
1
1
1
No.2 Screw Hole
for Mounting
Base
No.1 Screw Hole
for Bracket
4.Fix the camera to the wall with the supplied
screws.
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position (0° ).
2).Tighten No.3 adjusting screw.
3).Loosen No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0° ~ 360°).
6).Tighten No.1 adjusting screw.
~ 360°
5. Adjust the surveillance angle.
1). Loosen No.3 adjusting screw to adjust the pan
position ( .
3). Loosen No.2 adjusting screw to adjust the
tilting position( ).
5). Loosen No.1 adjusting screw to adjust the
rotation position .
0° ~ 360°)
2).Tighten No.3 adjusting screw.
0° ~ 90°
4).Tighten No.2 adjusting screw.
(0° ~ 360°)
6).Tighten No.1 adjusting screw.
2.3 Ceiling Mounting for Type IV
Camera
2.2 W Mounting for Type IIall / III
Camera
2.1 Ceiling Mounting for Type I
Camera
360°
360°
3
2
1
90°
Focus
Zoom
Adjusting Sheet
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable
Adjusting Screw