Network Convert Camera Quick Operation Guide UD.
Network Convert Camera·Quick Operation Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. About This Document This manual applies to the following camera models. Model DS-2CD6412FWD-10 DS-2CD6412FWD-20 DS-2CD6412FWD-30 This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual.
Network Convert Camera·Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Network Convert Camera·Quick Operation Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Network Convert Camera·Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. Warnings Follow these safeguards to prevent serious injury or death.
Network Convert Camera·Quick Operation Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
Network Convert Camera·Quick Operation Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C,or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use.
Network Convert Camera·Quick Operation Guide Table of Contents 1 Appearance Description ................................................................. 8 2 Installation .................................................................................... 12 2.1 Installation of Block-Shaped Sensor Unit ....................... 15 2.1.1 Concealed Mounting .......................................... 15 2.1.2 Exposed Mounting ............................................. 17 2.
Network Convert Camera·Quick Operation Guide 1 Appearance Description Camera Description The overview of the network bullet camera is shown below: 5 6 2 3 4 14 VIN1 AUDIO IN AUDIO OUT SD 7 13 1 9 8 LAN(PoE) RXD TXD GND IN1 1B 1A ALARM RESET RS232 DC 12V 12 10 11 15 Figure 1-1 The Covert Camera with Block-shaped Sensor Unit 8
Network Convert Camera·Quick Operation Guide 5 6 2 3 4 VIN1 AUDIO IN AUDIO OUT SD 7 16 18 1 9 8 LAN(PoE) 17 RXD TXD GND IN1 1B 1A RS232 ALARM DC 12V RESET 12 10 11 Figure 1-2 The Covert Camera with Cylindrical Sensor Unit 5 6 2 3 4 VIN1 AUDIO IN AUDIO OUT SD 7 20 1 19 9 8 LAN(PoE) RXD TXD GND IN1 1B 1A ALARM RS232 DC 12V RESET 12 10 11 Figure 1-3 The Covert Camera with Fixed Focal Unit 9
Network Convert Camera·Quick Operation Guide Table 1-1 Description of the Camera No. Description No.
Network Convert Camera·Quick Operation Guide LED Color& Status Indicator Solid red On normal operation POWER Unlit Power Off Solid green Camera works properly Unlit Camera does not work properly.
Network Convert Camera·Quick Operation Guide 2 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Make sure all the related equipment is power-off during the installation. Check the specification of the products for the installation environment. Make sure the power supply is matched with your required voltage to avoid damage.
Network Convert Camera·Quick Operation Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly. Steps: 1. Fix the standard mounting rail on the mounting surface.
Network Convert Camera·Quick Operation Guide For cement surface mounting, you need to use the expansion screw to fix the camera. For wooden surface mounting, you can just use the self-tapping screw to fix the camera. 2. Hang the hook which is on upper-side of the main unit onto the rail, press a little harder on the lower part of the main unit, and then the elastic clasp will be automatically buckled. As shown in figure below.
Network Convert Camera·Quick Operation Guide If you already had a standard rail installed, you can buckle the main unit onto the installed rail directly. As shown in figure below. Figure 2-3 Buckle the Main Unit onto Standard Rail 2.1 Installation of Block-Shaped Sensor Unit This series of camera support concealed mounting and exposed mounting with a decorative cover. 2.1.1 Concealed Mounting Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1.
Network Convert Camera·Quick Operation Guide Figure 2-4 Drill on the Surface Make sure the drilling hole is big enough for the camera lens. 2. Remove a side of the adhesive tape on the bracket. Paste the bracket on mounting surface by aligning with the drilled hole.
Network Convert Camera·Quick Operation Guide 3. Install the block-shaped sensor unit into the bracket and make it to be buckled. 4. Tighten the fastening screw on the top of the bracket. Figure 2-6 Insert the Block-shaped Sensor Unit 2.1.2 Exposed Mounting Steps: 1. Fix the Block-shaped sensor unit on the mounting surface with screws. As shown in figure below.
Network Convert Camera·Quick Operation Guide Figure 2-7 Fix the Block-shaped Sensor Unit For cement surface mounting, you need to use the expansion screw to fix the camera. For wooden surface mounting, you can just use the self-tapping screw to fix the camera. 5. Shield the sensor unit with the decorative cover. As shown in figure below.
Network Convert Camera·Quick Operation Guide Figure 2-8 Hood the Cover 2.2 Installation of Cylindrical Sensor Unit This series of camera only support concealed mounting. Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1. Drill on the mounting surface. As shown in figure below.
Network Convert Camera·Quick Operation Guide Figure 2-9 Drill on the Surface Make sure that the drilling hole is big enough for the camera lens. 2. Remove a side of the adhesive tape on the bracket. Paste the bracket on the mounting surface with aligning with the drilling hole. As shown in figure below. Figure 2-10 Paste the Bracket 3. Install the cylindrical sensor into the mounting hole in the round rail bracket.
Network Convert Camera·Quick Operation Guide 4. Turn the locking sleeve to fix the sensor. Figure 2-11 Install the Cylindrical Sensor 2.3 Installation of Fixed Focal Unit Steps: 1. Fix the mounting base of the bracket to the ceiling with the supplied screws. Figure 2-12 Fix the Ceiling Mounting Bracket 2. Hood the bracket cover to the mounting base.
Network Convert Camera·Quick Operation Guide Figure 2-13 Hood the Bracket Cover 3. Screw the bracket to the mounting base.
Network Convert Camera·Quick Operation Guide Another shorter bracket is also selectable, please select the bracket according to your demand. 4. Loop the fixed focal unit with the loop of the bracket, and tighten it with the supplied screw. As shown in Figure 2-15. Figure 2-15 Loop the Fixed Focal Unit 5. Align the assembled fixed focal unit to the bracket, and rotate the unit to tighten the unit with the bracket.
Network Convert Camera·Quick Operation Guide Figure 2-16 Install the Fixed Focal Unit to the Bracket 6. Loosen the knob to adjust the surveillance angle, and then tighten the lock nut to complete the installation.
Network Convert Camera·Quick Operation Guide 3 Setting the Network Camera over the LAN Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera. The following figure shows the cable connection of network camera and PC: Figure 3-1 Wiring over LAN Set the IP address of the camera for accessing via LAN. Steps: 1.
Network Convert Camera·Quick Operation Guide Use PCNVR software and to list the online devices. Please refer to the user manual of PCNVR client software for detailed information. 2. Change the IP address and subnet mask to the same subnet as of your PC.
Network Convert Camera·Quick Operation Guide Figure 3-2 Search Online Devices Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device list manually. The newly searched devices will be added to the list.
Network Convert Camera·Quick Operation Guide You can click or on each column heading to order the information; you can click to show the device table and hide the network parameter panel on the right side, or click to show the network parameter panel. Modify device information Steps: 1). Select the device to be modified in the device list as shown in Figure 3-3. The network parameters of the device will be displayed in the Modify Network Parameters panel on the right side as shown in Figure 3-4.
Network Convert Camera·Quick Operation Guide Figure 3-4 Modify Network Parameters 3. Enter the IP address of network camera in the address field of the web browser to view the live video. The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”. For accessing the network camera from different subnets, please set the gateway for the network camera after you log in.
Network Convert Camera·Quick Operation Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: 1. Open the web browser. 2.
Network Convert Camera·Quick Operation Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Convert Camera·Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1) 32
Network Convert Camera·Quick Operation Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
