E Series 5-inch Speed Dome User Manual UD.
1 User Manual of E Series 5-inch Speed Dome Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact the dealer. This manual is applicable to E Series 5-inch Speed Dome. This manual may contain several technically inaccurate points or printing errors, and the content is subject to change without notice. The updates will be added into the new version of this manual. We will readily improve or update the products or procedures described in the manual.
2 User Manual of E Series 5-inch Speed Dome Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
3 User Manual of E Series 5-inch Speed Dome Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
4 User Manual of E Series 5-inch Speed Dome Cautions: Make sure the power supply voltage is correct before using the product. Do not drop the product or subject it to physical shock. Do not install the product on vibratory surface or places. Do not expose it to high electromagnetic radiating environment. Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can cause fatal damage to the product.
5 User Manual of E Series 5-inch Speed Dome Table of Contents Chapter 1 Overview .............................................................................................................................................. 6 1.1 Description.................................................................................................................................................... 6 1.2 Functions ....................................................................................................
6 User Manual of E Series 5-inch Speed Dome Chapter 1 Overview 1.1 Description Integrated with the built-in pan/tilt unit, the high speed dome features highly sensitive response and reliable performance. The speed dome can be adopted in various surveillance fields with its full-integral functions and features, such as corridor, large venue, meeting room, station, community, etc. Figure 1-1 Appearance 1.2 Functions Note: The functions vary according to the different models of the speed dome.
7 User Manual of E Series 5-inch Speed Dome and panorama scanning. The scanning speed can be set by OSD menu from level 1 to 40, with the corresponding speed ranging from 1°/second to 40°/second. Preset Freeze Frame This feature freezes the scene on the monitor when going to a preset. This allows for smooth transition from one preset scene to another and also guarantees that masked area will not be revealed when going to a preset.
8 User Manual of E Series 5-inch Speed Dome recalled with a command from a controller or automatically by a configured function (park, time task, or power-up). By default the focus and iris are in auto status during the preset is being memorized. Power-off Memory This feature allows the dome to resume its previous position or status after power is restored. By default setting, the dome supports the power-off memory capability with the dwell time of 3 minutes.
9 User Manual of E Series 5-inch Speed Dome Chapter 2 Getting Started 2.1 Power-up Action After the power is connected, the speed dome will perform a series of self-test actions. It performs lens actions firstly, then the panning movement and the tilting movement at last. After the power-up self-test actions, the system information will be displayed for 2 minutes on the live view screen as shown below. TYPE DS- 2XXXX-X SN 000000000 ADDRESS COM FORMAT PROTOCOL 0 2400,8,1 ADAPTIVE HARDWARE 0.
10 User Manual of E Series 5-inch Speed Dome 2.2 Basic Operations You can operate the speed dome using a control device. The control devices include the control keyboards, DVRs, DVSs, etc. In this and the following chapters, operation of the speed dome by the IE browser of a DVR will be taken as an example. Panning and tilting: Click the direction buttons to control the pan and tilt movement of the speed dome. Zooming: Click the ZOOM+ and ZOOM- buttons to control the zooming.
11 User Manual of E Series 5-inch Speed Dome Note: For Manchester code control protocol, the system-defined presets with special functions are shown as below: Table 1-1 System-defined Presets of Manchester Code Control Protocol Set Preset NO. 65 66 69 70 71 72 Function Remote reboot Access main menu Stop recording pattern Record Pattern 1 Record Pattern 2 Record Pattern 3 Call Preset NO. 67 70 71 72 Function Auto-flip Run Pattern 1 Run Pattern 2 Run Pattern 3 2.
12 User Manual of E Series 5-inch Speed Dome Chapter 3 Menu Operation The OSD menu tree is shown in the following figure. Note: The menu varies depending on the model of speed dome. Figure 3-1 Main Menu Before you start: You can operate the speed dome using the on-screen display menu remotely by connecting to a DVR or a DVS (encoder). Examples of entering speed dome menu are listed as follows: Enter the menu by pressing buttons: PTZ -> REC -> 9 -> 5 on the front panel of the DVR.
13 User Manual of E Series 5-inch Speed Dome MAIN MENUS ENGLISH OFF EXIT Figure 3-2 Main Menu To move the cursor and operate the menu: Move the cursor up/down: On control panel of the live view interface of the DVR, click up and down direction buttons or FOCUS+ and FOCUS- buttons to move the cursor in the menu up and down.
14 User Manual of E Series 5-inch Speed Dome Enter the system information display menu: MAIN MENUS > SYS INFO SYS INFO DS- 0XXXXX-X TYPE ADDRESS 0 COM FORMAT 0000,0,0 PROTOCOL XXXXX VERSION 0. 00 HARDVERSION BUILD DATE BACK 0. 00 13 08 05 EXIT Figure 3-3 System Information Notes: Information on this menu cannot be edited. The temperature refers to the internal temperature of the speed dome. 3.2.
15 User Manual of E Series 5-inch Speed Dome Task 2: Set the broadcast address of the speed dome. When the BROADCAST ADDRESS is set to ON, the control devices with address 0 can control the speed dome remotely regardless of the address of the speed dome. With this function on, the control device with address 0 is capable of controlling all domes connected to it. This function is usually for debugging.
16 User Manual of E Series 5-inch Speed Dome Fan parameter configuration You can set the FAN CONTROL as ON or OFF. EIS (Electronic Image Stabilization) configuration You can set the EIS FUNCTION as ON or OFF; and set the EIS LEVEL as 0-3. Note: The selectable EIS levels vary depending on the camera models. Preset direct focus You can set the preset direct focus function ON/OF on PRESET DFOCUS submenu.
17 User Manual of E Series 5-inch Speed Dome CAMERA CAMERA WHITE BALANCE AUTO WIDE LIMIT 2.0 RED BLUE 210 150 CHROMA SUPPRESS SATURATION 1 1 IMAGE FLIP OFF CONTRAST OFF FOCUS LIMIT 1M HLC ON INIT LENS OFF HR MODE OFF NOISE REDUCE BACK LOW GAIN LIMIT BACK 15 EXIT EXIT Figure 3-6 Camera Settings Task 1: Configure the focus settings. Setting the focus mode Steps: (1) Move the cursor to FOCUS using the direction buttons and click IRIS+ to enter.
18 User Manual of E Series 5-inch Speed Dome Configure the zoom speed. Purpose: You can define the speed at which the lens changes from full wide zoom to the optical zoom. Steps: (1) Move the cursor to ZOOM SPEED using the direction buttons and click IRIS+ to enter. (2) Click up/down direction buttons to choose the speed from HIGH (default), MEDUIM and LOW. (3) Click IRIS+ button to confirm. Task 3: Configure the Day/Night mode. There are two parameters available for day/night mode configuration.
19 User Manual of E Series 5-inch Speed Dome define the iris value according to related content in this section if you choose IRIS mode. SHUTTER: User-defined shutter speed, auto iris and auto gain. It is the shutter-priority mode. Please define the shutter speed according to related content in this section if you choose SHUTTER mode. MANUAL: User-defined iris, gain and shutter.
20 User Manual of E Series 5-inch Speed Dome AUTO: In Auto mode, the dome retains color balance automatically according to the current color temperature. INDOOR, OUTDOOR: These two modes are for indoor use and outdoor use respectively. SELFDEF: In this mode, you can adjust the color temperature manually to meet your own demand. Note: In SELFDEF mode, you need to adjust the RED and BLUE values manually.
21 User Manual of E Series 5-inch Speed Dome Set the HR MODE as ON to adjust the resolution higher. Switch it OFF to disable the function, which can avoid cross color of the image. 3.3.2 Configuring Privacy Mask Purpose: Privacy mask enables you to cover certain areas on the live video from being live viewed and recorded. The masked areas can move with the panning/tilting movements and automatically adjust the size as the lens zooming in/out. Steps: 1.
22 User Manual of E Series 5-inch Speed Dome ADJUST BLANK POS FOCUS SHIFT STATUS SAVE: OPEN QUIT: CLOSE Figure 3-8 Set the Privacy Mask (2) You can see ADJUST BLANK POS message on the screen. Click the direction buttons to adjust the position of the privacy mask to the designed scene. (3) Click FOCUS+ button, and you can see ADJUST BLANK SIZE message on the screen. Click the up/down buttons to increase/decrease the height of the mask and click right/left buttons to increase/decrease the width of the mask.
23 User Manual of E Series 5-inch Speed Dome TITLE CODE TITLE Figure 3-9 Set Dome Title 7. Click the left/right direction buttons to position the cursor to the characters of the title. 8. Get the codes for a specific character and enter each code (number) by calling the preset number, i.e. calling presets 1-9 to enter number 1-9 respectively, and calling preset 10 to enter number 0. Note: You can get the codes of a specific character using the software we provided.
24 User Manual of E Series 5-inch Speed Dome Display the PTZ movements, alarm, system time, etc. Purpose: You can enable or disable the on-screen display of PTZ movements, presets, etc., and configure the display time. Steps: 1.
25 User Manual of E Series 5-inch Speed Dome 3.4.
26 User Manual of E Series 5-inch Speed Dome You can set IMAGE FREEZE as ON or OFF to enable or disable this function. Note: The function varies according to the different camera models. PTZ speed Purpose: You can define the speed of the dome movements. (1) DOME SPEED: The manual movement speed of the dome can be set from level 1 to 5. (2) SCAN SPEED: The scan speed defines the scan degree per second of pan scan, tilt scan, frame scan, random scan and panoramic scan.
27 User Manual of E Series 5-inch Speed Dome PRESETS PRESET NUM 1 [UNDEFINED] PRESET PTZ CLEAR PRESET BACK EXIT Figure 3-13 Preset Configuration Menu 2. Choose the preset number: Move the cursor to PRESET NUM and click IRIS+ to enter. Click the up and down buttons to choose the preset number which needs to be edited. If the preset has been defined, the preset label will be listed under the number; if it has not been defined, you will see the information UNDEFINED under the number.
28 User Manual of E Series 5-inch Speed Dome PATROLS PATROL NUM 1 EDIT PATROL PREVIEW CLEAR PATH PATROL_D BACK 30S EXIT Figure 3-14 Patrol Configuration Menu Choose the patrol number. Steps: (1) Move the cursor to PATROLS NUM and click IRIS+ to enter edit mode. (2) Click the up and down direction buttons to select the number of the patrol which is to be configured. (3) Click IRIS+ again to confirm the settings and exit edit mode of this column. Note: Up to 8 patrols can be configured.
29 User Manual of E Series 5-inch Speed Dome to cancel and return to the previous menu. Preview the patrol. Move the cursor to PREVIEW and click IRIS+ to preview the current patrol. You can click IRS+ again to stop the preview. Call the defined patrol. You can call the special presets to call the defined patrol. E.g. call preset 35 to call patrol 1. Please refer to Section 2.3 to find the corresponding preset number for each patrol. Delete a patrol.
30 User Manual of E Series 5-inch Speed Dome 3. Edit the pattern. Steps: (1) Move the cursor to EDIT PATTERN and click IRIS+ to enter edit mode. REMAIN MEMORY 100 DONE: OPEN QUIT: CLOSE Figure 3-17 Edit the Pattern (2) Click the PTZ control buttons and direction buttons to operate the speed dome to draw a movement path, including pan scan, tilt scan, zoom in, zoom out, etc. The speed dome can automatically memorize the path you operated as a pattern.
31 User Manual of E Series 5-inch Speed Dome 1. Move the cursor to enter the TIME TASK submenu: MAIN MENU > DOME SETTINGS > TIME TASK TIME TASK TASK NUM TASK STATE TASK ACTION 1 ON NONE TASK TIME TASK PREVIEW TASK CLEAR BACK EXIT Figure 3-18 Time Task Configuration Menu 2. Choose the task number. Steps: (1) Move the cursor to TASK NUM and click IRIS+ to enter edit mode. (2) Click the up/down direction buttons to select the number of the task which is to be configured.
32 User Manual of E Series 5-inch Speed Dome Note: The weekday can be set to be from Monday to Sunday or Whole Week; the H refers to Hour and the M refers to Minute. WEEK WHOLE WEEK START(H-M) 00 00 END(H-M) 00 00 DONE: OPEN QUIT: CLOSE Figure 3-19 Set the Task Time 6. Delete the task. Move the cursor to TASK CLEAR, click IRIS+ to delete the time and action of the current task, and click IRIS+ again to confirm the settings and exit. 3.4.
33 User Manual of E Series 5-inch Speed Dome 3. Configure the zone area. Steps: (1) Move the cursor to EDIT ZONE and click IRIS+ button to enter the edit mode. (2) You can see SET LEFT LIMIT on the screen. Click the direction buttons to set the left limit stop. (3) Follow the prompts on the screen to set the right limit, up limit and down limit. (4) Click IRIS+ button to save the settings and exit. 4. Set the zone status and scan status.
34 User Manual of E Series 5-inch Speed Dome DIAGNOSTICS DIAGNOSTICS HIGH TEMP 0 HIGHEST TEMP 47°C LOW TEMP 0 LOWEST TEMP 23°C VIDEO LOSS LOW VOLTAGE 0 0 POWER UP BACK PAN LOST 0 TILT LOST CAMERA LOST 0 0 0 BACK EXIT EXIT Figure 3-22 Self-diagnostics Table 3-2 Descriptions of self-diagnostics information Item HIGH TEMP HIGHEST TEMP LOW TEMP LOWEST TEMP VIDEO LOSS LOW VOLTAGE POWER UP Description The occurrence times of high temperature (higher than 65°C) The highest temperature The occu
35 User Manual of E Series 5-inch Speed Dome You can modify the password and enable/disable the password protection to prevent unauthorized settings of the speed dome. After you set and enable the password, you need to input the password every time you call preset 95 to enter the menu. Steps: 1. Move the cursor to enter the password modification submenu: MAIN MENU > DOME SETTINGS > PASSWORD > EDIT PASSWORD 2. Click IRIS+ to enter edit mode. 3.
36 User Manual of E Series 5-inch Speed Dome Zoom limit Zoom speed Slow shutter IR cut filter D/N level BLC AE mode Exposure compensation White balance Auto-flip Proportional pan Park time Park act Scan speed Image freeze Limit stops Time show Zone show Address show Error rate show Zoom/PT/Preset show Max Optical Zoom High Off Day Mid Off Auto 7 Auto On On 5 seconds None 28 Off Off Off On Off Off Off 3.5.
37 User Manual of E Series 5-inch Speed Dome Appendix Appendix 1 Lightning & Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W, like instantaneous lighting stroke, surging, etc. According to the actual outdoor situation, necessary protection measures must be taken, besides ensuring the electrical safety. The distance between signal transmission wires and High-voltage equipment or high-voltage cable is at least 50m.
38 User Manual of E Series 5-inch Speed Dome Appendix 2 RS485 Bus Connection General Property of RS485 Bus According to RS485 industry bus standard, RS485 is a half-duplex communication bus which has 120Ω characteristic impendence, the maximum load ability is 32 payloads (including controller device and controlled device). RS485 Bus Transmission Distance When using 0.
39 User Manual of E Series 5-inch Speed Dome faraway. At this time, the dome will be uncontrollable, or self-running, etc. 1# 6# 控 主 备 设 32# 15# Figure A-4 Star Shape Connection For such case, the best way is adding a RS485 distributor. This product can effectively change the star-shape connection to which satisfies the requirement of RS485 industry standard, in order to avoid those problems and improve the communication reliability. Show as figure 5.
40 User Manual of E Series 5-inch Speed Dome Problem dome can be controlled but not smoothly. Possible Reasons To Solve the Problem tightly. 2. RS485+ or RS485-wire is 2. Change a RS485 wire. broken. 3. The speed dome is too far away 3. Add a terminal resistor. from the remote control device. 4. Too many speed domes are 4. Add a RS485 distributor. connected. © Hikvision Digital Technology Co., Ltd. All Rights Reserved.
41 User Manual of E Series 5-inch Speed Dome Appendix 3 24VAC Wire Gauge & Transmission Distance The following table describes the recommended max. distance adopted for the certain wire gauge when the loss rate of 24VAC voltage is less than 10%. For the AC driven device, the maximum voltage loss rate is 10% allowable. For example, for a device with the rating power of 80VA which is installed at a distance of 35 feet (10m) away from the transformer, then 0.8000mm is required as the minimum wire gauge. 0.
42 User Manual of E Series 5-inch Speed Dome Appendix 4 Table of Wire Gauge Standards Bare Wire Gauge(mm) 0.750 0.800 0.900 1.000 1.250 1.500 2.000 2.500 3.000 American Wire Gauge AWG 21 20 19 18 16 15 12 British Wire Gauge SWG 21 20 19 18 17 14 © Hikvision Digital Technology Co., Ltd. All Rights Reserved. Cross-sectional Area of Bare Wire(mm2) 0.4417 0.5027 0.6362 0.7854 1.2266 1.7663 3.1420 4.9080 7.
