Installation guide INSTALL_LION-V6 2019/01 Edition Related HIKOB products: LION H-RT201A This document may not be reproduced (even partially) or communicated to 3rd parties without the written authorization of the company’s General Management. Copyright © HIKOB.
Installation guide INSTALL_LION-V6 2019/01 Edition Table of contents 1. Introduction................................................................................. 3 1.1 Symbols and conventions used in this guide .............................................. 3 1.2 Safety instructions .......................................................................................... 3 1.3 Compliance and conformity ........................................................................... 4 a. Europe ...
Installation guide INSTALL_LION-V6 2019/01 Edition 1. Introduction When using LION, safety precautions must be taken to avoid injury and damages. Please read this guide before installing, using the product, or performing any maintenance operation. Failure to read, understand and follow herein instructions may result in personal injury. In no event shall HIKOB be held liable for any damages arising out of or related to misunderstanding instructions detailed in this manual. 1.
Installation guide INSTALL_LION-V6 2019/01 Edition Modifications or changes on the product is strictly prohibited if it is not expressly approved by HIKOB. Modifications or changes performed on LION will void the user’s authority to operate the equipment. 1.3 Compliance and conformity a. Europe HIKOB SAS declares that the HIKOB LION product is in accordance with stipulations of the RED 2014/53/UE, CEM 2014/30/UE and 2014/35/UE directives. b.
Installation guide INSTALL_LION-V6 2019/01 Edition d. Canada Transmitter Antenna: Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropic ally radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Installation guide INSTALL_LION-V6 2019/01 Edition 2. General description 2.1 HIKOB Wireless sensor network acquisition system The LION is one of the elements that constitutes the HIKOB wireless sensor radio network. This system is a set of wireless sensors doing multi-point distributed measures in various domains. These sensors radio transmit their acquired data to the GATEWAY, possibly via LION routers, depending on environment constraints for radio transmission.
Installation guide INSTALL_LION-V6 2019/01 Edition suitable for outdoor installations. Should you decide to perform cleaning tasks on the GATEWAY, don’t perform high pressure cleaning, prefer wiping with a dry cloth, or with a neutral agent. It is delivered all assembled, ready to be fastened on a pole or a wall with provided accessories, please refer to the Installation section for details. 2.2.
Installation guide INSTALL_LION-V6 2019/01 Edition 3. Data sheet 3.1 General Power supply Consumption Dimensions Type of fixing Weight Operating and storage temperature Water index Rechargeable battery Li-ion 3,6V-2250mAh < 30mW 8 x 8 x 2.5 cm Pole or wall 150g -20°C à +60°C IP67 according to EN 60529 3.2 Wireless 3.2.1 HIKOB Network Frequency band Protocol Number of channels Output power Antenna gain Range 3.2.2 2.45GHz ISM IEE 802.15.
Installation guide INSTALL_LION-V6 2019/01 Edition 4. Installation 4.1 Overall methodology Installing an HIKOB radio network requires a good topology analysis of your site to maximize radio transmission quality by optimizing positions and numbers of HIKOB nodes in the network. A preliminary study done with your vendor determines elements that will constitute your HIKOB radio network acquisition.
Installation guide INSTALL_LION-V6 2019/01 Edition 4.2 LION Mounting procedure The LION is delivered ready to be installed, batteries are charged, so it is useable right away. As its emplacement is already determined by the site pre-study, the following sections explain the mounting procedure itself, and recommendations for final adjustments. Respect safety rules working at heights when installing the LION: use an elevating work platform, and appropriate PPE.
Installation guide INSTALL_LION-V6 2019/01 Edition For wall mounting: - Locate the installation location of the router and mark the four mounting holes for the plate. - Drill the four holes, insert the anchors appropriate to the nature of the support. - Attach the plate to the wall with four screws. - Repeat the above procedure in step 4. Figure 2 – HIKOB LION installed on a pole. c.
Installation guide INSTALL_LION-V6 2019/01 Edition Figure 3 – Orientation For the best compromise, choose a good radio coverage rather than the best exposure for the solar panel: the LION is designed to run with 1 hour of sunshine a day, and is autonomous 2 months in total darkness. Consider as well specific radiation patterns of the sensors involved in your HIKOB network, that is, WISECOW have conic ones. So, in that case, orient the antenna towards the ground.
