Operation Manual

MULTI-AMPLIFIER APPLICATIONS
5
Front/Rear high pass, using a 2 channel amplifier for mono sub bass
2 channel bass amplifier(COLOSSUS PRO is used in the example below):
The combination of a BOLTAR or COLOSSUS PRO and a JUPITER
- X-OVER switch: LP/BP
amplifier, utilizing their built in crossovers, makes it a snap to put together a
full system with front and rear highs, with mono sub bass.
- PARAMETRIC EQ FREQUENCY: X1
- CROSSOVER FREQUENCY: X1
Interconnect cable checklist:
- Using good quality RCA cables, feed the front and rear outputs of a head unit to
Please note that these frequency points are suggestions only. Refer to the
the inputs of the 4 channel JUPITER as shown.
loudspeaker manufacturer specifications and the section “Setting up systems
after installation for best performance”
- Also connect the LINE OUT of the JUPITER to the LINE INPUT of the 2
channel COLOSSUS PRO amplifier as shown.
Level control checklist:
Mono bass woofer wiring:
- Refer to the section “Setting up systems after installation for best performance”
Connect the mono speaker positive terminal to the LEFT +, and its negative
terminal to RIGHT -.
Minimum final loudspeaker impedances:
TITAN:
Switch setting checklist:
- 2-Ohm per channel in stereo mode.
4 channel highs amplifier:
- 4-Ohms mono bridged.
- 1/2CH X-OVER: HP
COLOSSUS PRO:
- PARAMETRIC EQ FREQUENCY: X10
- CROSSOVER FREQUENCY: X10
- 1-Ohm per channel in stereo mode.
- 2-Ohms mono bridged.
- 3/4CH X-OVER: HP
JUPITER:
- PARAMETRIC EQ FREQUENCY: X10
- CROSSOVER FREQUENCY: X10
- 2-Ohms per channel in stereo mode.
- 4-Ohms mono bridged.
STEREO
INTERCONNECT
RCA CABLE
BATT+12V
GROUND
SPEAKER OUTPUT
RIGHT LEFT
REM + - + -
BRIDGED
REMOTE TURN-ON
DUAL CHASSIS GROUND
DUAL BATTERY +12v
VIA FUSE
MONO SPEAKER
or SUBWOOFER
LL
RR
HFR-G1
REMOTE
SUBSONIC FREQUENCY BANDWIDTH CUT/BOOST
FREQUENCY RIGHT LEFT INPUT LEVEL
PARAMETRIC EQ
PHASE
DIAGNOSTIC
RED-SHORT CIRCUIT
AMBER-THERMAL
RED-CLIP
AMBER-NEAR CLIP
GREEN-PRE CLIP
HP LP/BP
FULL RANGE
X1 X10
FULL RANGE
OUTPUT
LINE
INPUT
15Hz 150Hz 40Hz 400Hz Narrow Wide -10dB +10dB 40Hz 400Hz 0 180 0 180 9V 0.2V
X1 X10
LP/BP
STEREO 12dB/OCT
MONO 24dB/OCT
LP DIRECT
POWER INPUT
GND REM BATT+12V
CH 1/2 SPEAKER OUTPUT CH 3/4
RIGHT LEFT RIGHT LEFT
- + - + - + - +
BRIDGED BRIDGED
HFR-G1
REMOTE
DIAGNOSTIC
RED-SHORT CIRCUIT
AMBER-THERMAL
RED-CLIP
AMBER-NEAR CLIP
GREEN-PRE CLIP
HP LP/BP
CROSSOVER
PARAMETRIC EQ PARAMETRIC EQ
HP
FULL RANGE
FULL
X1
X1
4CH
MODE
X1
X1
X10
X10
2CH
X10
X10
LINE INPUT
CH 3&4
CH 1&2
FREQUENCY FREQUENCY BANDWIDTH BOOST SUBSONIC LEVEL
40Hz 400Hz 40Hz 400Hz NARROW WIDE -10dB +10dB 15Hz 150Hz 9V 0.2V 40Hz 400Hz 40Hz 400Hz NARROW WIDE -10dB +10dB 9V 0.2V
FREQUENCY FREQUENCY BANDWIDTH BOOST LEVEL
4Ch
MONO MIX
OUTPUT
Ch1 Ch3 Ch2 Ch4
FUSE