Exhibit 08 Integrated Information Systems Group 8201 E. McDowell Road Scottsdale, AZ 85252-1417 Exhibit 8 – Users Manual DSMODEM/RTC Wireless LAN FCC ID: E9UDSMODEM-RTC Model No. DSMODEM/RTC 8.
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual LQWHUQDO XVH RQO\ 2001-01-09
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2001-01-09 Table of Content 1. INTRODUCTION and FEATURES. ……………………………………………… 3 2. OUTSIDE. ……………..……………………………………………………………. 4 3. Setting and Using. ………………………………………………………………... 7 3.1. Prepare the WS200 / WM200 wireless-LAN.. ……………………………. 8 3.2. Connecting WS200 / WM200 wireless-LAN. ……………………………. 8 4. Application…………………………………………………………………………. 9 5. Technical Specifications………………………………………………………… 10 6.
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2001-01-09 / WM200 wireless-LAN uses a standard RS-232C serial data external-interface that can be driven asynchronously. WS200 / WM200 wireless-LAN uses direct sequence spread spectrum technology implemented with Spread Spectrum Technology (SST). This can be applied for multiple-access networking or point-topoint, point-to-multiple, and multiple-to-multiple communication. 1.2.
Exhibit 08 M t l S t d S l ti 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual K 2001-01-09 2.1. Mobile has one connector, LED indicators. 1. RS-232 & Connector Power A DB-9 connector for connecting to data terminal equipment (DTE) and +12~+24V DC power input. 1,6 Power +12~+24V DC power input. 2 TX of RF-LAN RS-232C communication TX-line of RF-LAN. 3 RX of RF-LAN RS-232C communication RX-line of RF-LAN. 4,5,9 GND GND 2. Power LED This LED turns on when DC-Power on. 3.
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2.2. Mobile Configuration A. Mobile B. Mobile’s Antenna & Antenna Cable C. Mobile’s Communication/Power Cable 2.3. Station Configuration A. Station LQWHUQDO XVH RQO\ 2001-01-09
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual B. Station’s Antenna & Antenna Cable C. Station’s Antenna Extension Cables Antenna Cable Antenna Extension Cables D. Station’s Communication Cables E. Station’s Power Adapter & Power Cable LQWHUQDO XVH RQO\ 2001-01-09
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 3. Setting and Using LQWHUQDO XVH RQO\ 2001-01-09
Exhibit 08 M t l S t d S l ti 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual K 2001-01-09 3.1. Prepare the WS200 / WM200 wireless-LAN The following sections describe how to connect the WS200 / WM200 wirelessLAN to External Device and how to set up and operate the WS200 / WM200 wireless-LAN. 3.1.1.
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2001-01-09 For Station, A. One side of the RS-232 cable connects connector on the rear panel of Station, and the other side connects with the serial port of PC (BMS). B. Four-antenna extension cables connect on each point. (See Figure 2-5) C. Station’s antenna & antenna cable connects with Station. (Please, do not use other device might cause the rf-power variation.) D. Place the antenna on higher position. E.
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2001-01-09 5. Technical Specifications RF-Frequency Range 902-928MHz LQWHUQDO XVH RQO\
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2001-01-09 RF-Channel Spacing 2.048 MHz RF-Transmission Power 20 ± 2 dBm RF-Modulation Scheme GMSK RF-Radio Technique Direct Sequence Spread Spectrum RF-Duplex Mode Half-duplex RF-Number of Channel 10 RF-Operation Mode Point-to-point RF-PN Code Chip Rate 1.
Exhibit 08 M t l S t d S l ti K 902 ~ 928 MHz Wireless-LAN WS200 / WM200 User Manual 2001-01-09 A. Check wired connection condition. B. Reconnect wired connection. C. Please. Call repair-department. 6.2. When Status LED didn’t flicker by 10-second, periodically. A. Check wired connection condition. B. Reconnect wired connection. (And, Please. Call repair-department.) 6.3. When Validator display “RF1”-> “Fail” (Mobile can’t wired-communicate with validator). A. Check wired connection condition. B.
