User Manual
Table Of Contents
- Advantage Series Proximity TM ARK-501+ PinProx Proximity Readers Models
- ARK-501+ ARK-501+, 3 x 4 Matrix
- 1.0 Product Specification
- 2.0 Introduction
- Figure 1 ARK-501+ Block Diagram
- 2.1 Guidelines
- 1. Metal affects radio signals.
- 2. Care must be exercised to reduce or eliminate unwanted signals from external sources. The exte...
- 3. The read range is proportional to the type of card used. Larger cards read at greater distance...
- 4. The rules and regulations of the Federal Communication Commission (FCC) and other regulatory a...
- 2.2 Features
- 3.0 The Keypad
- 3.1 Buffered Mode
- 3.2 Unbuffered Mode
- 3.3 Model ARK-501+, 3 x 4 Matrix
- 4.0 Quick Hook-Up Procedure
- 1. Unpack the equipment and become familiar with the components.
- 2. Read the pre-installation hints for mounting and metal mounting the reader as detailed on page17
- 3. Place the reader at least 3.5' (1.1 m) from any CRT (monitor).
- 4. Locate and read the appropriate wiring diagram detailed on page21 through page25.
- 5. Connect the reader to the host controller according to instructions shown on the wiring diagram.
- 6. Connect reader to the appropriate linear power supply, refer to page19.
- 7. Connect to earth ground as noted in the instructions on page20.
- 8. Apply power.
- 9. Present the access card parallel to the reader as described in the card presentation section (...
- 10. IF the read range is not per specifications, make sure any monitor is far enough away from th...
- 11. If no code is present, you have a communications problem with the controller.
- 12. Press all keys on the keypad and verify reception of codes (per the tabulated data on page7 ...
- 13. If anything appears abnormal, please answer the questions on the Troubleshooting Data Form (p...
- 4.1 Card Presentation
- 1. Unpack the equipment and become familiar with the components.
- 5.0 Physical Dimensions
- 6.0 Pre-Installation Hints
- 7.0 Power and Cabling
- 8.0 Earth Grounding
- 9.0 Single LED Control Line Configuration
- 10.0 Dual LED Control Line Configuration
- 11.0 Magnetic Stripe Output Wiring Diagram
- 12.0 Wire Types and Lengths
- 13.0 Troubleshooting
- 14.0 Additional Information
- Index
.5HY$
1RYHPEHU
$
$5.
$5.[0DWUL[
$XGLR³%HHSHU´7RQH
&
FDEOHPLQLPXPJDXJH
FDUGSUHVHQWDWLRQ
&(PDUN
FHUWLILFDWLRQ
FRS\ULJKWV
FXUUHQWLQSXW
'
GLPHQVLRQV
GXDO/('FRQWURO
'XDO/('&RQWURO/LQHV
(
HDUWKJURXQG
)
IUHTXHQF\
*
JXLGHOLQHV
+
KRRNXSSURFHGXUH
.
.H\SDG
0
PDJQHWLFVWULSHRXWSXWZLULQJ
PHWDO0RXQWLQJ
PRXQWLQJ
2
RXWSXWGDWD
3
SDWHQWV
SRZHUVXSSO\
SRZHULQSXW
SURGXFWVSHFLILFDWLRQ
4
4XLFN)ODVK
5
UHDGUDQJH
UHWXUQPDWHULDODXWKRUL]DWLRQ50$
6
6HOI7HVW
VLQJOH/('FRQWURO
6LQJOH/('&RQWURO/LQH
7
WUDGHQDPHV
WUDGHPDUNV
WURXEOHVKRRWLQJ
9
YROWDJHLQSXW
:
ZLUHW\SHVUHFRPPHQGHG
,QGH[