User Manual
Table Of Contents
- Advantage Series Proximity TM ARK-501+ PinProx Proximity Readers Models
- ARK-501+ ARK-501+, 3 x 4 Matrix
- 1.0 Product Specification
- 2.0 Introduction
- Figure 1 ARK-501+ Block Diagram
- 2.1 Guidelines
- 1. Metal affects radio signals.
- 2. Care must be exercised to reduce or eliminate unwanted signals from external sources. The exte...
- 3. The read range is proportional to the type of card used. Larger cards read at greater distance...
- 4. The rules and regulations of the Federal Communication Commission (FCC) and other regulatory a...
- 2.2 Features
- 3.0 The Keypad
- 3.1 Buffered Mode
- 3.2 Unbuffered Mode
- 3.3 Model ARK-501+, 3 x 4 Matrix
- 4.0 Quick Hook-Up Procedure
- 1. Unpack the equipment and become familiar with the components.
- 2. Read the pre-installation hints for mounting and metal mounting the reader as detailed on page17
- 3. Place the reader at least 3.5' (1.1 m) from any CRT (monitor).
- 4. Locate and read the appropriate wiring diagram detailed on page21 through page25.
- 5. Connect the reader to the host controller according to instructions shown on the wiring diagram.
- 6. Connect reader to the appropriate linear power supply, refer to page19.
- 7. Connect to earth ground as noted in the instructions on page20.
- 8. Apply power.
- 9. Present the access card parallel to the reader as described in the card presentation section (...
- 10. IF the read range is not per specifications, make sure any monitor is far enough away from th...
- 11. If no code is present, you have a communications problem with the controller.
- 12. Press all keys on the keypad and verify reception of codes (per the tabulated data on page7 ...
- 13. If anything appears abnormal, please answer the questions on the Troubleshooting Data Form (p...
- 4.1 Card Presentation
- 1. Unpack the equipment and become familiar with the components.
- 5.0 Physical Dimensions
- 6.0 Pre-Installation Hints
- 7.0 Power and Cabling
- 8.0 Earth Grounding
- 9.0 Single LED Control Line Configuration
- 10.0 Dual LED Control Line Configuration
- 11.0 Magnetic Stripe Output Wiring Diagram
- 12.0 Wire Types and Lengths
- 13.0 Troubleshooting
- 14.0 Additional Information
- Index
1RYHPEHU
.5HY$
:LUH7\SHVDQG/HQJWKV
)RU :LHJDQG DQG 0DJQHWLF 6WULSH RXWSXW ZLULQJ UHIHU WR WKH WDEOH EHORZ WR GHWHUPLQH WKH UHFRP
PHQGHG ZLULQJ W\SH DW YDULRXV PD[LPXP GLVWDQFHV 9DULDWLRQV LQ GLVWDQFHV UHTXLUH GLIIHUHQW ZLUH
JDXJHV%HFDXVHRIV\VWHPGDWDWHUPLQDWLRQGLIIHUHQFHVFRQWDFW\RXUV\VWHPPDQXIDFWXUHUIRULWVH[DFW
UHTXLUHPHQWV
5HFRPPHQGHG:LUH7\SHV
$:*PPVL[RUVHYHQFRQGXFWRUZLWKDQRYHUDOOIRLOVKLHOG%HOGHQ
RUHTXLYDOHQW
$:*PPVL[RUHLJKWFRQGXFWRUZLWKDQRYHUDOOIRLOVKLHOG$OSKDRU
HTXLYDOHQW
$:*PPVL[RUHLJKWFRQGXFWRUZLWKDQRYHUDOOIRLOVKLHOG$OSKDRU
HTXLYDOHQW
)LJXUH&DEOH/HQJWK'HILQLWLRQ
1RWHV
7KHLQSXWYROWDJHVKRXOGEH9'&WR9'&DWWKHUHDGHU
UHIHUWR3RZHU&DEOH0D[L
PXP/HQJWKRQSDJH
5HIHUWR\RXUV\VWHPPDQXIDFWXUHUVLQVWUXFWLRQVIRUWKHLUH[DFWZLUHW\SHVSHFLILFDWLRQV
,QVWDOODWLRQWREHLQDFFRUGDQFHZLWK1DWLRQDO(OHFWULF&RGH$16,1)3$
Cable Length
Cable Type
ARK-501
Host
C ontroller
Cable Length
500'
(154 m )
500'
(154 m )
24 A W G
(0.60 m m D ia.),
M ulti-C onductor,
Belden 9536, 9537
22 A W G
(0.80 m m D ia.),
M ulti-C onductor,
Alpha 5196, 5198
18 A W G
(1.20 m m D ia.),
M ulti-C onductor,
Alpha 5386, 5388
500'
(154 m )
1
2
3
6
5
4
7
8
9
#
0
*










