User Manual
Table Of Contents
- Advantage Series Proximity TM ARK-501+ PinProx Proximity Readers Models
- ARK-501+ ARK-501+, 3 x 4 Matrix
- 1.0 Product Specification
- 2.0 Introduction
- Figure 1 ARK-501+ Block Diagram
- 2.1 Guidelines
- 1. Metal affects radio signals.
- 2. Care must be exercised to reduce or eliminate unwanted signals from external sources. The exte...
- 3. The read range is proportional to the type of card used. Larger cards read at greater distance...
- 4. The rules and regulations of the Federal Communication Commission (FCC) and other regulatory a...
- 2.2 Features
- 3.0 The Keypad
- 3.1 Buffered Mode
- 3.2 Unbuffered Mode
- 3.3 Model ARK-501+, 3 x 4 Matrix
- 4.0 Quick Hook-Up Procedure
- 1. Unpack the equipment and become familiar with the components.
- 2. Read the pre-installation hints for mounting and metal mounting the reader as detailed on page17
- 3. Place the reader at least 3.5' (1.1 m) from any CRT (monitor).
- 4. Locate and read the appropriate wiring diagram detailed on page21 through page25.
- 5. Connect the reader to the host controller according to instructions shown on the wiring diagram.
- 6. Connect reader to the appropriate linear power supply, refer to page19.
- 7. Connect to earth ground as noted in the instructions on page20.
- 8. Apply power.
- 9. Present the access card parallel to the reader as described in the card presentation section (...
- 10. IF the read range is not per specifications, make sure any monitor is far enough away from th...
- 11. If no code is present, you have a communications problem with the controller.
- 12. Press all keys on the keypad and verify reception of codes (per the tabulated data on page7 ...
- 13. If anything appears abnormal, please answer the questions on the Troubleshooting Data Form (p...
- 4.1 Card Presentation
- 1. Unpack the equipment and become familiar with the components.
- 5.0 Physical Dimensions
- 6.0 Pre-Installation Hints
- 7.0 Power and Cabling
- 8.0 Earth Grounding
- 9.0 Single LED Control Line Configuration
- 10.0 Dual LED Control Line Configuration
- 11.0 Magnetic Stripe Output Wiring Diagram
- 12.0 Wire Types and Lengths
- 13.0 Troubleshooting
- 14.0 Additional Information
- Index
1RYHPEHU.5HY$
3K\VLFDO'LPHQVLRQV
)LJXUH3K\VLFDO'LPHQVLRQV
1RWHV
0XOWLFRORU/('DQGDXGLREHHSHUDUHVWDQGDUGZLWKWKH$5.UHDGHU
$63$GYDQWDJHHULHV3UR[LPLW\HTXLSPHQWLVQRWFRPSDWLEOHZLWK(63(OHFWUR6WDWLF
3UR[LPLW\RU(63(6HULHV3UR[LPLW\
5HIHUWR\RXUV\VWHPPDQXIDFWXUHUVLQVWUXFWLRQVIRULWVH[DFWLQVWDOODWLRQVSHFLILFDWLRQV
6SHFLILFDWLRQVVXEMHFWWRFKDQJHZLWKRXWQRWLFH
0RWRUROD,QGDOD&RUSRUDWLRQ
4.55"
(11.56cm )
2 x M ounting H ole
0.17" (0.43cm )D IA Thru,
0.3" (0.76cm ) D IA C 'B ore,
0.4" (1.0cm ) D eep
3.0"
(7 .6 c m )
F ro n t V ie w w ith o u t B e z e l
F ro n t V ie w w ith B e z e l
Side V iew
12"
(30.75cm )
0.65"
(1.65cm )
Cables
3.3"
(8 .5 c m )
4.45"
(1 1 .3 c m )
2.83"
(7 .2 c m )
0..47"
(1.19cm )
LED
L
C
0.47"
(1..18 cm ")
Beeper
1
2
3
6
5
4
7
8
9
#
0
*
1.68"
(4.25 cm )
2.23"
(5.65cm )
1
2
3
6
5
4
7
8
9
#
0
*
R eader
Cable
0.80"
(2.03 cm )
3x4 M atrix
Keypad C able
1.52"
(3.86 cm )