User Manual
Table Of Contents
- Advantage Series Proximity TM ARK-501+ PinProx Proximity Readers Models
- ARK-501+ ARK-501+, 3 x 4 Matrix
- 1.0 Product Specification
- 2.0 Introduction
- Figure 1 ARK-501+ Block Diagram
- 2.1 Guidelines
- 1. Metal affects radio signals.
- 2. Care must be exercised to reduce or eliminate unwanted signals from external sources. The exte...
- 3. The read range is proportional to the type of card used. Larger cards read at greater distance...
- 4. The rules and regulations of the Federal Communication Commission (FCC) and other regulatory a...
- 2.2 Features
- 3.0 The Keypad
- 3.1 Buffered Mode
- 3.2 Unbuffered Mode
- 3.3 Model ARK-501+, 3 x 4 Matrix
- 4.0 Quick Hook-Up Procedure
- 1. Unpack the equipment and become familiar with the components.
- 2. Read the pre-installation hints for mounting and metal mounting the reader as detailed on page17
- 3. Place the reader at least 3.5' (1.1 m) from any CRT (monitor).
- 4. Locate and read the appropriate wiring diagram detailed on page21 through page25.
- 5. Connect the reader to the host controller according to instructions shown on the wiring diagram.
- 6. Connect reader to the appropriate linear power supply, refer to page19.
- 7. Connect to earth ground as noted in the instructions on page20.
- 8. Apply power.
- 9. Present the access card parallel to the reader as described in the card presentation section (...
- 10. IF the read range is not per specifications, make sure any monitor is far enough away from th...
- 11. If no code is present, you have a communications problem with the controller.
- 12. Press all keys on the keypad and verify reception of codes (per the tabulated data on page7 ...
- 13. If anything appears abnormal, please answer the questions on the Troubleshooting Data Form (p...
- 4.1 Card Presentation
- 1. Unpack the equipment and become familiar with the components.
- 5.0 Physical Dimensions
- 6.0 Pre-Installation Hints
- 7.0 Power and Cabling
- 8.0 Earth Grounding
- 9.0 Single LED Control Line Configuration
- 10.0 Dual LED Control Line Configuration
- 11.0 Magnetic Stripe Output Wiring Diagram
- 12.0 Wire Types and Lengths
- 13.0 Troubleshooting
- 14.0 Additional Information
- Index
1RYHPEHU.5HY$
)LJXUH$5.%ORFN'LDJUDP
*XLGHOLQHV
$V WKLVWHFKQRORJ\LVEDVHGRQ UDGLR IUHTXHQF\RQHPXVW H[HUFLVH VRPH H[WUD FDUH LQVWDOOLQJ WKHVH
SURGXFWV7KHIROORZLQJREVHUYDWLRQVDSSO\
0HWDODIIHFWVUDGLRVLJQDOV
&DUHPXVWEHH[HUFLVHGWRUHGXFHRUHOLPLQDWHXQZDQWHGVLJQDOVIURPH[WHUQDOVRXUFHV7KHH[WHU
QDOVRXUFHVVXFKDVVRXUFHVRI5)VLJQDOWUDQVPLWWHUVSRUWDEOHWZRZD\UDGLRFHOOXODU
SKRQHVHWFDQGRUQHDUE\(0,QRLVHSURGXFHUVPD\FRQWULEXWHWRGLVWXUELQJWKHHOHFWULFDO
HQYLURQPHQWRIWKHUHDGHU'HSHQGLQJRQWKHH[WHUQDOQRLVHVLJQDOVWUHQJWKRIWKHQHDUE\
WUDQVPLWWHUWKHUHDGUDQJHPD\EHUHGXFHGRUWKHFDUGVLJQDOPD\EHPDVNHGE\WKHH[WHUQDO
VLJQDOUHVXOWLQJLQDQRUHDG
7KHUHDGUDQJHLVSURSRUWLRQDOWRWKHW\SHRIFDUGXVHG/DUJHUFDUGVUHDGDWJUHDWHUGLVWDQFHVWKDQ
VPDOOHUFDUGV
7KHUXOHVDQGUHJXODWLRQVRIWKH)HGHUDO&RPPXQLFDWLRQ&RPPLVVLRQ)&&DQGRWKHUUHJXODWRU\
DJHQFLHVLQYDULRXVFRXQWULHVOLPLWWKH5)SRZHUOHYHODQGIUHTXHQF\0RWRUROD,QGDOD5),'UHDG
HUVDUHRIWKHW\SHDFFHSWHGXQGHU)&&3DUW
)HDWXUHV
$XGLR³%HHSHU´7RQH$OO$5.¶VLQFOXGHDQDXGLR³EHHSHU´WRQHEXLOWLQDVDVWDQGDUGIHD
WXUH7KHEHHSHULVDFWLYDWHGGXULQJSRZHUXSLQWKH6HOI7HVWPRGHDQG
ZKHQDQDFFHVVFUHGHQWLDOLVVXFFHVVIXOO\UHDG
7UL&RORU/('$63$GYDQWDJHHULHV3UR[LPLW\UHDGHUVFRPHVWDQGDUG
ZLWKDWULFRORU/('UHGJUHHQDQGDPEHU%RWKVLQJOHOLQHDQGGXDO
OLQHYHUVLRQVRI/('FRQWURODYDLODEOH
6LQJOH/('&RQWURO/LQH7KH/('LVUHGZKHQWKH/('FRQWUROOLQHLVKLJK7KH/('WXUQV
JUHHQZKHQWKH/('FRQWUROOLQHLVSXOOHGORZ,IWKHOLQHLVWRJJOHGKLJK
Card
Field From R eader
Energizes C ard
C ard S ends D ata
To R eader
3 x 4 M atrix
Keypad C able*
Power
Power
Supply
C ontroller
AR K-501+
1
2
3
6
5
4
7
8
9
#
0
*
R eader S ends D ata
to H ost C om puter
* The 3x4 m atrix cable is only available on the A R K -501+, 3x4 m atrix m odel.