Hickory Industries, Inc. Installation Manual USA Hickory Rotisseries Models: N/5.5 E Machine Type N / 5. 5 E Total Power Rating 6000 or 8400 Watts Elements / Spits 4 Elements with 5 Spits Electrical Rating 208/240 V or 380/410 V Temperature Range 200ºF - 550ºF Timer Manual or Fully Automatic Delivery Date: Final Inspection: 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.
Hickory Industries, Inc. Table of Contents 1.0 Installation Instructions 3 1.1 General Information 4 1.2 Description of the Data Plate 4 1.3 Machine Drawings and Dimensions 6 1.4 Electrical Conversion and Adjustment Instructions 7 1.5 Cooking Cycle 7 1.6 Maintenance, Response to Technical Problems 7 1.6.1 Reasons for Problems and Solutions 8 1.7 Spit Drive Mechanism 9 1.8 N/5.5E Parts List 10 1.9 N/5.5E Exploded View 12 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.
Hickory Industries, Inc. 1.0 Installation Instructions a. When installing these units, it is important to comply with the most recently established rules and regulations as deemed pertinent by the local and national electrical, ventilation, sanitation, and fire codes. These units are classified by Underwriters Laboratories, Inc. as Electrically Heated Food Service Equipment. b. Electric units must not be directly connected to a flue or exhaust vent.
Hickory Industries, Inc. 1.1 General Information The Operating Instructions are to be given to the operator of the rotisserie. All unit operators are to be familiar with the functions of the rotisserie. The Operating Instructions should be kept in a location close to the rotisserie. It should be easily recognizeable and easily accessible. Electric units can be ordered to meet most electrical specifications.
Hickory Industries, Inc. HICKORY INDUSTRIES, INC. HICKORY INDUSTRIES, INC. NORTH BERGEN, NJ 07047 NORTH BERGEN, NJ 07047 MODEL: N/5.5 E M SERIAL NO. MODEL: MOTOR: 208 - 220 VOLTS 60 CYCLE AC CURRENT WATTS SINGLE PHASE 3 RPM HEATING ELEMENTS 208 VOLTS 60 CYCLE 3 PHASE AC CURRENT 1400ELEMENTS WATTS PER ELEMENT LISTED 607C 4 ® TOTAL WATTAGE 6000 MFG. DATE N/5.5 E M SERIAL NO.
Hickory Industries, Inc. 1.3 Machine Drawings and Dimensions The following drawing of the Front View, Side View, and Top View indicate where the dimensions are taken and should be used to plan the installation of the units. N/ 5.5 E Top View Front View Right Side View N/ 5.5 E inches mm Height 29" 737 Width 39-1/4" 997 Depth 22-1/16" 560 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.
Hickory Industries, Inc. 1.4 Electrical Conversion and Adjustment Instructions Before converting or adjusting the machine to another type of electricity, it is imperative that electrical power to the machines should also be turned off. When converting, make sure that the proper electrical diagram is followed and that the motor and timer match the connected single phase voltage! 1.5 Cooking Cycle In order to start the cooking cycle, the elements must be powered.
Hickory Industries, Inc. 1.6.1 Reasons for Problems and Solutions Problem Unit does not heat. a. Cause Rotisserie not "on". 1. 2. 3. 4. Unit takes too long to cook. a. Solution Make sure that the TEMPERATURE switch is on. Thermostat must be set (i.e. 550°F). The cooking timer must be operational (cook cycle). A red LED on the TEMPERATURE switch indicates that the contactor is supplying power to the heating elements. Using the electrical diagram, make sure that the entire system is fully functional.
Hickory Industries, Inc. 1.7 Spit Drive Mechanism This unit is equipped with a planetary motion spit drive system. This means that each spit is turning upon its axis at the same time that they turn about the center shaft. When the motor switch is turned to on, the disks and the spits will begin to turn. Insure that the mechanism turns smoothly when testing the unit. Aluminum Drive Disk Center Shaft Spit Before cooking, it is imperative that the center shaft be covered and protected with aluminum foil.
Hickory Industries, Inc. 1.8 N/5.5E Parts List Item Qty. Description Material Length Size 553 554 519 520 5/8" Manufacturer 1 1 1 1 1 1 Shaft 5/8 (Removable Drums - Center) Shaft Locking Slide Drive Bearing Holder (Left - with brass bearing) Drive Bearing Holder (Right - with teflon bearing) Brass Shaft Bearing Teflon Shaft Bearing SS SS Steel (Chromed) Steel (Chromed) Brass Teflon 501 502 503 504 514 564 505 1 1 1 1 1 5 Aluminum Disk Drive (Bare) Aluminum Disk Slave (Bare) Alum. Disk Drv.
Hickory Industries, Inc. 1.8 N/5.5E Parts List (Contd.) Item Qty.
Hickory Industries, Inc. 1.8 N/5.5E Exploded View 4900 Westside Avenue, North Bergen, New Jersey 07047 N/5.
Hickory Industries, Inc. Glass Replacement on the 5.5E & 10.10E Machines Make sure that the handle and all associated hardware is available at the site or order the mounting kit from Hickory. Make sure that the glass bar is in the open position. Make sure that the handle and all associated hardware is available at the site or order the mounting hardware from Hickory. Glass handle, flat washer, lock washer, 10/32 screw Glass Closed Position The glass mounts between the glass handle and the flat washer.
Hickory Industries, Inc. Replacing the front glass Insert the screw on to the glass (use hi heat Loc-tite). As a hint, start with the middle screw it will give you some leverage with the glass. DO NOT TIGHTEN. This will ensure that you have enough play to move the glass around without bumping the glass. Proceed with the remaining screws (use hi heat Loctite). Make sure that the glass is sandwiched between silicone washer and the silicone spacer.
Hickory Industries, Inc. If the glass is not evenly spaced, adjust the glass until its evenly spaced. CAUTION: If the screws are not snug enough, when lowering the glass door, the glass my hit the screws and chip the glass. CAUTION: When tightening the screws, if the glass shifts down, the glass door will be too close to the roof of the machine when the glass door is shut. Open door and tighten upper mounting screws. Close the door and verify that the side and bottom spacing is even all around.
