Manual Revision File number：YFZ-2015-0741 Revision Date Nov.2015.
Preface Preface Introduction Welcome to use Hi-target V100 receiver, this introduction is applicable to Hi-Target V100 products. V100 is a new type of GNSS receiver used for measurement. The introduction describes how to install, set and use V100 products. Experience Requirement In order to help you better use Hi-Target series products, Hi-Target suggests you carefully reading the instruction. If you are unfamiliar with V100 products, please refer to www.hi-target.com.
V100 GNSS RTK System User Manual Warning: the contents here generally are very important. In case of failing to operate based on warning contents, it will damage the machine, lose the data, break down the system and endanger personal safety. Exclusions Before using the products, please carefully read the operating instruction, and it will help you better use the product. Hi-Target Surveying Instrument Co.
Preface separate notice. We have checked the consistency between contents in instruction and software & hardware, without eliminating the possibility of deviation. The pictures in operating instruction are only used for reference. In case of inconformity with products, the products shall prevail. Technology and Service If you have any technical issues, you can call company technology department for help, we will answer your question in time.
V100 GNSS RTK System User Manual 2. Log in hi-target official website, download the electronic version introduction in “Download Center” → → “Manual” “Surveying Products” Advice If you have any advice or suggestion on V100, please call us or Dial the national hotline: 400-678-6690. Your feedback information will improve the production quality more.
Content Content Product Introduction ...................................... 1 Preface ............................................... 2 Product Characteristics ............................... 3 Cautions for Use ...................................... 3 Introductions to Receiver ................................. 5 Receiver Appearance ................................... 6 Control Panel ......................................... 6 Upper Cover ........................................... 7 Bottom Cover ..........
V100 GNSS RTK System User Manual Preface .............................................. 33 Five-pin Socket ...................................... 33 Five-wire ............................................ 34 Mini USB Cable ....................................... 36 Measurement Bench Marker ............................. 37 Schedule 1 control panel lights .......................... 38 Schedule2 factory default parameters .....................
Product Introduction CHAPTER Product Introduction 1 This chapter describes: ■ Preface ■ Product Characteristics ■ Cautions for Use 1
Product Introduction Preface V100 is a new subminiaturized type of GNSS receiver used for measurement pushed forward by Hi-Target Brand, used a delicate design, Magnesium alloy construction, multi-satellite and multi-frequency technique, built-in constellation motherboard, Bluetooth both with dual-mode and long-distance , it is a realization of quick, efficient , safe measurement GNSS receiver. Warning: the instruction represents no standard configuration.
V100 GNSS RTK System User Manual product. Product Characteristics A new generation of subminiaturized GNSS RTK， equipped with new efficient intelligent real-time core platform; Using BDS constellation system, Support BDS, GPS, GLONASS; Subminiaturized zero-phase antenna ; Built-in 4.0 standard long-distance dual-mode Bluetooth, backward compatible 2.
Product Introduction maintenance the sophisticated instruments. Warning: the receiver shall be in stipulated temperature range upon using and storage. The detailed requirements are shown in ChapterⅣ: Technical Parameters—> Environment Characteristics.
V100 GNSS RTK System User Manual CHAPTER Introductions to Receiver 2 This chapter describes: ■ Receiver Appearance ■ Control Panel ■ Upper Cover ■ Bottom Cover ■ Power Supply System ■ Environmental Requirements ■ Electronic Jamming 5
Introductions to Receiver Receiver Appearance The product appearance is divided into three sections，upper cover, bottom cover and control panel. upper cover bottom cover control panel Figure 2-1 Control Panel The control panel includes a power switch button, three indicators, namely satellite lights, power light (bi-color light), signal light (bi-color light).
V100 GNSS RTK System User Manual and so on. Upper Cover Color Mode Loss Prevention boss Figure 2-2 Loss Prevention boss: boss can effective anti-wear; Color Mode: appearance of the structure, Clear , beautiful, drop Bottom Cover Including battery compartment, five-pin socket,Mini USB interface.
Introductions to Receiver 3 2 4 1 5 1- Screw connection 2- Battery compartment 3- Five-pin socket 4-Mini USB interface 5- protective plug Figure 2-3 Connection screw: for the instrument fixed to the base or the pole. Battery compartment: for housing lithium batteries. Five-pin socket: For connection to the host and external data links and external power source.
V100 GNSS RTK System User Manual Protective plug: socket for dust and waterproof. Note: If it is unnecessary to use five-pin socket, and USB interface, please cover the rubber plug to prevent dust. Power Supply System Battery and adapter Table 2.
Introductions to Receiver Figure 2-5 Recharge V100 lithium battery shall use PSAI10R-050Q power adapter to charge, about 7 hours of charging time. Warning: 1. only the battery and charger configured by the manufacturer can be used; the battery shall not be thrown into fire or used in metal short circuit electrode. 2. It shall stop using in case of heating, deformation, liquid leakage, smelling or other abnormal reactions during using, charging or storage process. It shall exchange new battery. 3.
V100 GNSS RTK System User Manual Battery cover button Figure 2-6 2) Align battery pole with battery compartment pole, boost until it flush with battery cover and the mental button upspring.
Introductions to Receiver Figure 2-8 3) Close the battery cover to finish installing. Removal Push up the battery cover button to uncover it, then press the metal button and remove battery. Power supply Table 2.2 power supply mode power power supply supply mode internal：lithium battery external：USB, Five-pin socket scope of USB socket：DC power 4.2-5.5V/1.
V100 GNSS RTK System User Manual NOTE: 1. The service life of lithium battery will decrease along with the decrease in temperature and increase in charging-discharging times. A new 6300 mAh lithium battery can be used for 7 hours upon collection of static data or rovel operation. 2. In order to prolong the service life of battery, it shall charge the battery within 24 hours after using up, or the battery performance will be damaged. 3.
Introductions to Receiver Corrosive liquids or gases Electronic Jamming The receiver shall not be installed in the place near to strong electric power and interference signal, such as: Oil duct (spark plugs) Television and computer display Generator Battery-operated motor cycle DC-AC power supply changeover equipment Fluorescent lamp Power supply 14
V100 GNSS RTK System User Manual CHAPTER 3 Elementary Operation This chapter describes: ■ Control Panel ■ Function Key ■ LED Function ■ Working Pode Switch ■ Rovel Handheld Difference ■ Static Collection ■ Static Data Storage ■ Static Data Download ■ Firmware Upgrading 15
Elementary Operation Control Panel Most settings and operations of receiver are completed using a key on control panel. Power key Satellite light Status light Power light Figure 3-1 Function Key Table 3.
V100 GNSS RTK System User Manual automatically set the base station Operating mode Double-click the button to enter switching the operating mode switching, double-click each time a working mode switch(switch between static and RTK mode) Status Inquiry Click power light ,red light flash flashing, displays power Reset Motherboard Boot state, long press the button more than 6 seconds, all lights flash at the same time, release the button, reset motherboard LED Function Different settings mode indicator dis
Elementary Operation 1：0％~25％ 2：25％~50％ 3：50％~75％ 4：75％~100％ Signal light Off Static mode (Status Green) Long-term RTK mode lighting Data light (Status Red) Slow flash 1. RTK mode: flash as difference data interval 2.
V100 GNSS RTK System User Manual signal light (red) flash as difference data interval. NOTE：Working mode switch: You can also switch by handheld, please refer to the specific operation "Hi-Survey Software User's Guide" RTK mode setting : equipment → base\rovel → data line; static mode: setting equipment → Accessibility → static capture settings. Rovel Handheld Difference When the host working mode is rovel, the data line has two types: external data link and handheld difference.
Elementary Operation Figure 3-2 Figure 3-3 Handheld difference rovel working mode setting: In rovel setting interface, select data line “handheld”, select server, setting IP, port, group number and other parameters, click “setting” to finish setting. “Operator”: Hangheld automaticly acquires it according to SIM card network operator. “Server IP”: manual input server IP, port; you can also acquire by clicking “select”, select the server you need from list.
V100 GNSS RTK System User Manual base and rovel should setting the same parameters. “Network”: ZHD and CORS, select ZHD when using hi-target server, select CORS when using CORS network.
Elementary Operation Checking difference network state: click to the “difference network state” interface. If user have connected receiver and set as rovel handheld difference operation,click directly “disconnect” to stop handheld transmitting difference; click “connect to server” to transmits difference. Figure 3-6 Static Collection 1. Set up the instrument at the measurement point, the point is to strictly, and leveling. 2.
V100 GNSS RTK System User Manual shall be measured to the center point mark stone on top of the instrument of measurement reference member.V100 receiver measuring reference member radius 0.130m. measurement reference height measurement point Figure 3-7 3. Record point name, instrument number, instrument height, beginning observing time. 4. Boot, set the host to the static measurement mode. Satellite light flashing indicates it is searching for satellites.
Elementary Operation sampling interval, indicating that the acquisition of one epoch. 5. After the measurement is completely shutdown, record shutdown time. 6. Download processing data. Note ：You cannot move the base equipment and change acquisition parameters in the data collection. Static Data Storage Collected GNSS static data is stored in "static" disk that 8GB internal storage of V100 receiver, effective storage space is 6.
V100 GNSS RTK System User Manual Figure 3-8 Note：When the receiver storage space is less than 10MB, data light (red) fast flash, and it stop recording data, the existing data files will not be overwritten. Static Data Download Receiver file management download directly without download programs in the way of U disk storage. It can only download static data and can’t write or read the receiver.
Elementary Operation file. Figure 3-9 The steps of modify point name and antenna height of downloaded static file are: 1. Choose *. GNS files and double click the mouse. 2. Modify point name and input antenna height in the popping up dialogue of “file edit”, and then click “OK”. Figure 3-10 Note：The static files in removable disk can be deleted by handheld software rather than deleting directly.
V100 GNSS RTK System User Manual way. Figure 3-11 1. Open receiver, connect to computer by a random configuration USB cable. Open “my computer”, there will be "update" upgrading disk. 2. Copy host firmware (it can be downloaded from the official website or obtained from the technician) to "update" upgrading disk, then remove U disk, unplug the cable, restart the receiver to complete the upgrading.
Technical parameters CHAPTER 4 Technical Parameters This chapter describes: ■ GNSS Configuration ■ System Configuration ■ Built-in Communication ■ Control Panel ■ External Interface ■ Electric Characteristics ■ Physical Characteristics ■ Environment Characteristics ■ Private Cloud Service 28
V100 GNSS RTK System User Manual GNSS Configuration System core：use international first-class PCC new efficient intelligent real-time core Channel number：220 BDS：B1、B2 GPS：L1 C/A、L2E、L2C、L5 GLONASS：L1 C/A、L1 P、L2 C/A（Limited GLONASS M and L2P） GALILEO：Upgrading reserve Output format：ASCⅡ：NMEA-0183 and binary : Trimble GSOF Difference support：sCMRx、CMR、CMR+、 RTCM2.1/2.2/2.3/3.0/3.
Technical parameters Initialization reliability : >99.9% Data update rate : <20Hz System Configuration Operation system：intelligent real-time system boot time: 1s Data storage：built-in 8GB storage Built-in Communication Daul mode Bluetooth communication Control Panel Panel: one key Indicator：three bi-color LED lights External Interface 1 USB interface 1 five-pin interface Electric Characteristics Battery : high capacity lithium 6300mAh/3.
V100 GNSS RTK System User Manual Physical Characteristics Core control chip CotexA8, built-in 16GB Flash memory Size：127.
Socket and Main Accessories CHAPTER 5 Socket and Accessories Main This chapter describes: ■ Preface ■ Five-pin Socket ■ Five-wire ■ Mini USB Wire ■ Measurement Bench Marker 32
V100 GNSS RTK System User Manual Preface The chapter will introduce the appearance and application of main interface and accessories of V100. The following equipment does not represent all V100 users purchased. There will be different according to different configurations, the specific configuration shall be subject to the delivery order upon purchasing. Five-pin Socket Figure 5-1 Figure 5-2 1.
Socket and Main Accessories 1 GND 2 GND 3 Vin 4 RXD 5 TXD 2. All the circular sockets of this company start numbering pin in counterclockwise positive; circular pins start numbering pin in welding face counterclockwise. 3. All the above data out(TXD), in(RXD) signals explain by receivers. TXD is transmitting receiver data signal line, RXD is receiving receiver data signal line. 4.
V100 GNSS RTK System User Manual five-pin socket five-pin socket Figure 5-3 Five-wire: Connecting host and External radio, transmitting difference data; Plug the red dot Socket red dot Figure 5-4 Warning: 1.
Socket and Main Accessories socket, or it will damage the receiver socket and plugs of various lines. 2. When plug out the plug, directly grasp the sliding collar and pull out the plug with effort. It shall not rotate the plug. 3. After using the cable it shall place the cable in the place that are difficult for extrusion to prevent damaging the plug.
V100 GNSS RTK System User Manual one end and Mini USB interfaces.
附录 Schedule 1 control panel lights Operating Power Light (Green) Power Light (Yellow) Power Light (Red) Table 1 control panel lights illustrate Meaning Long-term lighting Full battery Long-term lighting Full battery voltage: internal battery≥3.
V100 GNSS RTK System User Manual Schedule2 factory default parameters Table 2 Factory default parameters Options Content The factory set parameters System parameters Working mode Rover Data Link Handheld difference Differential Mode RTK Text format RTCM(3.
Appendix Schedule3 Key accessories information Table 3 key accessories information name version manufacturer Main index performance Motherboard BD970 Trimble 220channels Antenna Small measuring zero phase antenna Hi-Target Surveying Instrument Co., Ltd. 51dB Databoard ZHD20150010B [PCBA] Hi-Target Surveying Instrument Co., Ltd.
V100 GNSS RTK System User Manual -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.
