HP Slate 6 VoiceTab Plus Tablet Maintenance and Service Guide IMPORTANT! This document is intended for HP authorized service providers only.
© Copyright 2014 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation.
iv Safety warning notice
Table of contents 1 Product description ........................................................................................................................................... 1 2 External component identification ..................................................................................................................... 3 3 Illustrated parts catalog .....................................................................................................................................
7 Power cord set requirements .......................................................................................................................... 28 Requirements for all countries ............................................................................................................ 28 Requirements for specific countries and regions ............................................................................... 28 8 Recycling ......................................................................
1 Product description Category Description Product Name HP Slate 6 VoiceTab Plus Tablet Processor Qualcomm® MSM8926 1.20-GHz quad core processor, soldered on circuit (SoC) Panel 6.0-in, (1280×720), LCD, 5-point capacitive TouchScreen display panel, bonded, full lamination, OGS; includes display panel cable and TouchScreen cable Memory Supports 1.0-GB LPDDR3 system memory Mass storage Supports a 16.
Category Description Power requirements Supports a 3000-mAh, Li-ion battery (non-removable), USB charging Supports a 5-V, 2-A AC adapter with DC plug and localized cable plug support 2 Operating system Preinstalled: Android 4.4.
2 External component identification 3
4 Item Component Item Component (1) Audio-out (headphone)/Audio-in (microphone) jack (6) Front-facing webcam (2) Rear-facing webcam (7) Volume control buttons (2) (3) Micro USB 2.
3 Illustrated parts catalog Locating the product number and the serial number The tablet product number (1) and serial number (2) are located inside the tablet back cover. This information may be needed when travelling internationally or when contacting support. See Back cover on page 13 for information on removing the back cover.
Tablet major components 6 Item Component Spare part number (1) Back cover 788634-001 (2) Battery, 3000-mAh (includes cable) 751655-001 (3) Middle frame 788635-001 Button Actuators Kit, includes: 790367-001 (4a) Power button actuator (4b) Volume button actuator (5) Rear-facing webcam (8.
Miscellaneous parts Component Spare part number AC adapter: 10-W, wall-mount, USB, AC adapter, non-PFC 743820-001 10-W, 5.3-V/2-A, USB, AC adapter with duck head for use in North America 744423-008 10-W, 5.3-V/2-A, USB, AC adapter with duck head for use in Europe 744423-009 HP headset 790368-001 HP Slate 6 VoiceTab Plus Tablet equipped with a Qualcomm MSM8926 1.20-GHz quad core processor (SoC), graphics subsystem with UMA memory, 1.0-GB LPDDR3 system memory, and 16-GB eMMC hard drive, and a 6.
Sequential part number listing 8 Spare part number Description 743820-001 10-W, wall-mount, USB, AC adapter, non-PFC 744423-008 10-W, 5.3-V/2-A, USB, AC adapter with duck head for use in North America 744423-009 10-W, 5.
4 Removal and replacement preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Magnetic screw driver ● Phillips P0 screw driver ● Plastic case utility tool Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ● Place items on a grounded surface before removing items from their containers.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
5 Removal and replacement procedures Tablet component replacement procedures CAUTION: Tablet components described in this chapter should only be accessed by an authorized service provider. Accessing these parts can damage the tablet and void the warranty. This chapter provides removal and replacement procedures for authorized service provider only parts. There are as many as 12 screws that must be removed, replaced, and/or loosened when servicing the tablet.
3. Remove the back cover (3). Reverse this procedure to install the back cover. Battery Description Spare part number Battery, 3000-mAh, (includes cable) 751655-001 Before removing the battery, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3.
1. Use the finger notch (1) to release the bottom edge of the battery (2) from the middle frame. 2. Remove the battery (3). Reverse this procedure to install the battery.
Middle frame Description Spare part number Middle frame 788635-001 Before removing the middle frame, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4. Remove the back cover (see Back cover on page 13). 5.
NOTE: If the power button actuator or the volume button actuator should become displaced during the removal of the middle frame, install the actuators into the openings in the middle frame as indicated in the following illustration. The fingers (1) on the ends of the actuators should be installed on the slots (2) and (3) on the middle frame. The actuators are included in the Button Actuators Kit, spare part number 790367-001. Reverse this procedure to install the middle frame.
Rear-facing webcam Description Spare part number Rear-facing webcam (8.0-MP, auto-focus, with flash; includes cable and double-sided adhesive) 789611-001 Before removing the rear-facing webcam, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3.
Antenna board Description Spare part number Antenna board (includes RF cable and double-sided adhesive) 773133-001 Before removing the antenna board, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4.
Reverse this procedure to install the antenna board. Speaker and vibrator module Description Spare part number Speaker (bottom, includes vibrator module, double-sided adhesive, and cables) 790370-001 Before removing the bottom speaker and vibrator module, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2.
3. Release the bottom speaker (3) from the molding built into the display panel assembly. 4. Remove the bottom speaker and vibrator module. Reverse this procedure to install the bottom speaker and vibrator module. System board Description Spare part number System board equipped with a Qualcomm MSM8926 1.20-GHz quad core processor (SoC), graphics subsystem with UMA memory, 1.
1. Disconnect the following cables from the system board: (1) RF antenna cable (2) Ambient light sensor board cable (3) TouchScreen cable 22 2. Release the top speaker cable (4) from the clip built into the display panel assembly.xxx 3. Detach the top speaker (5) from the display panel assembly. (The top speaker is attached to the display panel assembly with double-sided adhesive.
4. Disconnect the following cables from the system board: (1) Rear-facing webcam cable (2) Front-facing webcam cable (3) Display panel cable (4) Vibrator module cable 5. Remove the Phillips PM1.3×3.3 screw (1) that secures the system board to the display panel assembly.
6. Remove the system board (2). Reverse this procedure to install the system board. Front-facing webcam Description Spare part number Front-facing webcam (2.0-MP, fixed-focus; includes cable) 789610-001 Before removing the front-facing webcam, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2.
1. Turn the system board upside down. 2. Disconnect the front-facing webcam cable (1) from the system board. 3. Remove the front-facing webcam (2). Reverse this procedure to install the front-facing webcam. Ambient light sensor board Description Spare part number Ambient light sensor board (includes cable and double-sided adhesive) 790369-001 Before removing the ambient light sensor board, follow these steps: 1. Turn off the tablet.
Remove the ambient light sensor board: 1. Detach the ambient light sensor board from the display panel assembly. (The ambient light sensor board is attached to the display panel assembly with double-sided adhesive.) 2. Remove the ambient light sensor board and cable. Reverse this procedure to install the ambient light sensor board.
6 Specifications Metric U.S. Width 8.32 cm 3.28 in Height 16.51 cm 6.50 in Depth 0.89 cm 0.35 in Weight 160 g 0.35 lb Dimensions (portrait orientation) Input power The tablet operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated 100—240 V, 50/60 Hz. NOTE: The tablet can operate on DC power using an industry-standard micro-B USB cable. The HP adapter included with the tablet is recommended for charging the tablet.
7 Power cord set requirements The wide-range input feature of the tablet permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set included with the tablet meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the tablet is used.
Country/region Accredited agency Applicable note number Sweden CEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used. 2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor.
8 Recycling When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle.
Index A AC adapter, spare part numbers 7, 8 ambient light sensor board removal 25 spare part number 6, 8, 25 antenna board removal 19 spare part number 6, 8, 19 audio, product description 1 audio-in jack 4 audio-out jack 4 F front-facing webcam location 4 removal 24 spare part number G grounding guidelines guidelines equipment 12 grounding 10 packaging 11 transporting 11 workstation 11 B back cover removal 13 spare part number 6, 8, 13 battery removal 14 spare part number 6, 8, 14 battery guage 4 Button A
connectors 9 plastic parts 9 serviceability, product description 2 SIM, spare part number 7, 8 speaker location 4 removal 20 spare part number 6, 8, 20 system board removal 21 spare part number 6, 8, 21 T tablet major components 6 spare part numbers 7, 8 specifications 27 tools required 9 transporting guidelines 11 U USB 2.
