Quick Start Guide

QuickSpecs
HP ProDesk 400 G6 DM / AIO – G7 MT / SFF
Technical Specifications – Power
Not all configuration components are available in all regions/countries.
c06640086 – DA 16665 – Worldwide — Version 2 — August 26, 2020
Page 83
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
Less than 100 microamps
of leakage current at 264
Vac with the ground wire
intact with normal
polarity, as required for
Non-patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
Less than 100
microamps of leakage
current at 264 Vac with
the ground wire intact
with normal polarity, as
required for Non-
patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
Less than 100
microamps of leakage
current at 264 Vac with
the ground wire intact
with normal polarity, as
required for Non-
patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
Less than 100
microamps of leakage
current at 264 Vac with
the ground wire intact
with normal polarity, as
required for Non-
patient Electrical
Appliances and
Equipment used in a
patient care facility or
that contact patients in
normal use. Per section
10.3.5.1.
Power Supply Fan
N/A
50mm variable speed
70mm variable speed
N/A
Power cord length
6.0 ft. (1.83 m)
6.0 ft. (1.83 m)
6.0 ft. (1.83 m)
6.0 ft. (1.83 m)
Dimensions
65W: 102 x 55 x 30 mm
90W : 127 x 50 x 30 mm /
132 x 57 x 30 mm
200 x 85 x 53 mm
165 x 95 x 73 mm
90W : 127 x 50 x 30
mm / 132 x 57 x 30 mm
120W : 148 x 75.5 x
25.4 mm
150W : 160 x 80 x 40
mm
The power supply shall comply with harmonic input current requirements as detailed in EN61000-3-2 and JEIDA MITI standards.
The harmonic input current requirements must be met under the following operating conditions:
Load Requirements: 50% and 100%
Input Voltage: 230Vac/50Hz.
For active power factor correction the power factor at 50% &100% loads shall be greater than 0.9 over the entire nominal input
voltage range (100-127VAC and 200-240VAC).
Condition
Standard Efficiency
82/85/82%
85/88/85%
87/90/87%
90/92/89%
Input Voltage
10% of Rated Load
-
75%
81%
84%
86%
115Vac/60HZ
20% of Rated Load
-
82%
85%
87%
90%
115Vac/60HZ
50% of Rated Load
-
85%
88%
90%
92%
115Vac/60HZ
PF>0.9
PF>0.9
PF>0.9
PF>0.9
PF>0.95
100% of Rated Load
70%
82%
85%
87%
89%
115Vac/60HZ
PF>0.9
PF>0.9
PF>0.9
PF>0.9
PF>0.9
230Vac/50HZ