Evaporative cooling works on the principle of heat absorption by moisture evaporation. Simply put, heat is removed from the air as water evaporates. You feel this principle in action when you step out of a swimming pool or shower and feel cool as water evaporates from the surface of your skin. Your evaporative cooler works on the same principle.
STOP!!! READ THIS FIRST Do not return this item to the place of purchase unless instructed to do so by Hessaire customer support If you should find any missing parts, any loose, or dislodged items or have any questions please call us first. We have parts and expert support that can help you. We value your business and are here to help. We can ship any replacement or warranty parts to you quickly so your Hessaire mobile cooler can keep you cool. Hessaire Customer Service Centers Hessaire Products, Inc.
Use all precautions and disconnect from power source before performing any maintenance. Getting started Tools / Materials Needed: Contents: Evaporative Cooler (1) Drill with #2 Phillip’s bit Hardware Bag (1) Or Phillip’s head screwdriver Casters (4) Operating Instructions Evaporative cooling works on the principle of heat absorption by moisture evaporation. Simply put, heat is removed from the air as water evaporates.
Hessaire Products Inc. Manufacturing Warranty EVAPORATIVE COOLER Each new cooler is warrantied to be free from defects in material or workmanship for one full year from the date of original purchase. If a component is found to be defective in this one year period, it will be repaired or replaced with a new or refurbished product at the option of the factory. Should a warranty issue arise, please contact the dealer from whom the fan was purchased.
Section 3 Getting started Key Operational Points: 1. Your cooler must be positioned in front of an open window or door if it is to operate effectively. 2. Always ensure that there is another open window or door through which the air can exhaust from the room. 3. Ensure the filter is kept clean throughout the summer season. 4. At the end of each day run your cooler on FAN ONLY for 30 minutes to dry out the filter. 5. Prior to putting your cooler away for winter, always: a. Drain the tank and wipe out clean.
Safety Rules 1. Read and follow all instructions, cautions, and warnings. Failure to do so could result in personal injury, death or property damage. 2. Unit must be in the OFF position and UNPLUGGED from power receptacle before performing any maintenance. 3. Make sure the electrical power source conforms to the requirement of the evaporative cooler(s) as well as local codes. 4. To reduce the risk of fire or electrical shock, do not expose electrical connections to water. 5.
Section 4A Cooler Set Up and Operation 1. Lay the cooler down 2. Unscrew two screws, remove the bottom panel 3. Take out casters(x4), Screws(x16), flat washer(x16) and garden hose adapter(x1) 4. Install the garden hose adapter to the float valve assembly 5. Install 4 casters 6. Your cooler is ready to go! Hessaire Coolers are pre-assembled and ready to operate. Simply remove the packaging and then carefully remove the unit from the box. Install Casters.
Section 4B Connecting to a power supply. Plug the Hessaire cooler into any 115 volt power supply. It is permissible to use extension cords when needed. It is not recommended to use a GFCI circuit usually found in garage or patio areas. These outlets/circuits are sensitive and may trip inadvertently to the cooler in normal operation. Should that be the only power supply please be aware of this and if the GFCI trips simply reset it.
Section 4C Using the Control Switches Mechanical Version Rotary Switch/Motor Speed Has 4 positions. (Clockwise from OFF) OFF, LOW Fan Only, MED Fan Only, HI Fan Only. Pump Switch Controls the pump Middle Rocker Switch Controls the fan Oscillation Power Switch Controls power to the main controls, it will be lit when it is in the ON position, dark when OFF. When it is OFF the other switches will not function.
Rotary Switch/ Motor Speed has 4 Positions (clockwise from OFF) Fan OFF, LOW Fan, MED Fan, HIGH Fan. Pump Variable Control Button/ Low Water Indicator This button will blink red if low water level is detected and pump operation will be interrupted. It will continue to blink until proper water level is achieved. Press for Pump OFF light- Pump will be off Press for Pump Variable light. (Middle light) The pump will cycle on and off allowing the pad to become wet and then start to become dry.
Draining the Cooler Tank Unscrew drain cap from drain assemble and drain away water. You may tip the unit carefully to the drain side to help drain all the water out. Removal and Replacement of Xel50 Cooling Media. The cooling pads are made from a special resin impregnated craft paper specially designed for evaporative cooling. They will last many years if maintained properly and water quality is maintained. It is not necessary to remove the pads to clean them.
away. Be careful not to break the pin although the new pads will come with new pins and disc. The newer models will have a threaded disc that will unscrew from the pin 2. With disc removed, remove the pins from the pads and carefully remove pads from the fixed side mounting frame. Then do the same for the back panel or panels. 3. Xel50 pads are made with a 45/45 flute and can be installed either side to the frame.
No.
QUICK TROUBLESHOOTING TABLE Problem 1. Cooler fails to work at all 2. Cooler does not pump 3a. Fan does not operate 3b. Fan runs slow at start up 4. Louver does not operate Cause/Remedy 1.1 Check that the unit is plugged properly. 1.2 Check the POWER switch, push it to "ON". 1.3 The TIMER switch is "OFF", turn it to "ON". 1.4 Make sure cooler is not plugged into a tripped GFIC outlet. If so, reset GFCI or move to non GFCI outlet. 2.1 Pump is not activated. Push the PUMP switch to "ON". 2.
14
