AI Face Recognition Device Quick Start Guide Please read the Quick Start Guide carefully before using the product and keep it.
About this Manual Use this manual as a guide. The photos, graphics, icons, etc. provided in the manual are for explanation purposes only, and may differ from the specific products. Please prevail in kind. This manual may be upgraded later for product upgrading or other request needs; For the lastest version, pls contact our after sales.
1. Products Description AI face recognition device adopts dual-core ARM Cortex-A7 chip, wide dynamic high-definition binocular camera, 10.1-inch large screen, which supports face capture, face comparison, mask detection, face recognition, human identification verification, IC card reading and other verification methods, and it supports multiple networking methods such as wired network, WiFi, 4G (optional).
3. Wire Interface ① ② ③ ④ ⑤ 1 3 1 3 1 2 ⑥ ⑦ 1 2 ⑧ ① RESET (Long press to restore factory settings) ② USB2.0 interface, connect to mouse or USB ③ Access control interface (1.NO, 2.NC, 3.COM) ④ Wiegand interface（1.D0，2.D1，3.GND） ⑤ 1.Alarm out+, 2.Alarm out⑥ RJ45 network port, access to Ethernet ⑦ 1.RS485+，2.
4. Device Installation 4.1. Install TF card and SIM card If you need to use a TF card to store your access records, or use a SIM card for 4G Internet access, please install a TF card or SIM card before installing the device. If you don't need to use TF card or SIM card, you can skip this chapter.
① ⑤ ④ ③ Ejection Tool ⑥ ② SIM Card TF Card Card Tray 4.2. Install The Bracket Step 1 Insert the wire interface on the bracket rod into the device interface. Step 2 Use a wrench to tighten the screws on the device and the bracket rod. Step 3 Open the bracket rod and the bottom of the device to the maximum angle, and use a wrench to tighten the screws under the device and the bracket rod.
4.3. Install The Antenna Step 1 Aim the antenna with the connector on the rear shell and turn it clockwise to tighten it. Step 2 Fold the antenna at 90° to the back of the device. ① ② 4.4. Install On The Turnstile The device can be installed on turnstiles, desktop supports and T-pillars of different heights. They are installed in the same way; here is an example of installation on a turnstile.
② ③ ① Boot： According to the introduction of the wire interface, connect the device to the network so that the device and the configuration computer are under the same router, and power on. Note Face recognition distance: 1.2m-2.0m, it is recommended to paste a mark on the floor mark distance.
5. Platform Operation 5.1. Platform Installation Step 1 Under the Windows operating system, double-click "SDP2000_EN_x64_VX.X.X.exe", and follow the prompts to perform the installation. Step 2 After the installation is complete, the desktop displays the SDP2000 Sever platform icon. 5.2. Add Device Step 1 Double-click on the desktop " " to enter the login interface. (Google Chrome or Firefox browser is recommended).
The device default values are as follows: IP Address: "192.168.1.88" Subnet Mask: "255.255.255.0" Step 5 Select the device and click " click "Set".
5.3. Import Face Library Step 1 [Input personnel images in batches] After logging into the platform, click "Personnel → Personnel → Input personnel images in batches" - select pictures - "Upload" and the pictures are added into the device. [Input personnel information in batches] When importing pictures in batches, the pictures must meet the following requirements: Note 1. The picture naming format can be set as: name.jpg, name_department name.jpg, name_department name_personnel number.
Step 3 After the gallery is added into device it can realize face recognition.
Note When abnormality occurs on the SDP2000l platform, such as abnormal reading or abnormal data interface request, please follow the steps below: Right-click the running SDP2000 icon in the lower right corner of the desktop to check whether the status of Nginx, Mysqld, and SDP2000 is green (normal state). If any item is displayed in gray, restart the software to make it green. 6.
6.2. Face Recognition Configuration Step 1 Click "Advanced Configuration → Face Recognition" on the device web interface to enter the device face recognition configuration interface. Step 2 Turn on "Stranger Passage", "Detection Mask", "Snapshot Switch" and "Passing Record Keeping" as needed, and set the relay time, direction and other parameters. Step 3 Click "Save" to complete the configuration.
6.4. Online Upgrade Prerequisites: The device is connected to the Internet. Auto online upgrade: Step 1 On the device web interface,click "Configuration→System Configuration→Maintain". Step 2 Check "Auto Online upgrade", every Wednesday (this time can be set to other day) the equipment automatically detects whether there is a new version online, when "New version detected, update or not" is displayed, click "Upgrade" . The device interface displays "Upgrade will start after reboot.
