Smart Device 2000 Quick Start Guide Please read the Quick Start Guide carefully before using the product and keep it.
About this Manual Use this manual as a guide. The photos, graphics, icons, etc. provided in the manual are for explanation purposes only, and may differ from the specific products. Please prevail in kind. This manual may be upgraded later for product upgrading or other request needs; For the lastest version, pls contact our after sales.
1. Products Appearance 1.1. Front MIC IR LED Camera Fill Light 5”HD Screen Loudspeaker 1.2.
2. Wire Interface 1.D0 2.D1 3.GND D0 D1 GND RS485 RS485A RS485B NC COM NO GND DC12V 1.NC 2.COM 3.
3. Device Installation 3.1. Installed On The Desktop Step 1: Turn the camera end of the device upward and turn it to the back. Step 2: Put the silicone ring into the screw hole position on the inside of the desktop bracket. Silicone Desktop Stand Step 3: Align the holes of the bracket with the holes of the device, and fasten the bracket to the body with screws.
Step 4: Connect wires. To spread the desktop stand and adjust the angle as needed. 3.2. Wall Mounted Step 1: According to the installation sticker, open holes on the wall and install the rubber plug.
Step 2: Pass the network cable and 10PIN wire through the wall bracket, and arrange the wire into the wire groove, then fix the bracket to the wall with screws. Wall Bracket Step 3: Connect wires, install the device on the wall bracket, then align the screw holes on the left and right sides, install the nuts and lock the screws.
4. Platform Operation Boot According to the introduction of the wire interface, connect the device to the network so that the device and the configuration computer are under the same router, and power on. 4.1. Platform Installation Step 1: Under the Windows operating system, double-click "SDP2000_EN_x64_VX.X. X.exe", and follow the prompts to perform the installation. Step 2: After the installation is complete, the desktop displays the SDP2000 Sever platform icon. SDP2000 4.2.
4.3. Add Device Step 1: After logging into the platform, check "Resource - Device - Search Device".
Step 2: Select the device, click " " to modify the device IP, and click "Submit". The device is turned on "DHCP" by default after leaving factory. If the device is not connected to a DHCP server, but DHCP is set to "On", the default values are as follows: IP Address: "192.168.1.88" Subnet Mask: 255.255.255.0 Port: "80" (Some device ports are "7080") Step 3: Select the device and click " and click "Set".
4.4. Device Configuration After logging in to the platform, enter the "Device" interface and click " " to configure the basic parameter and other parameter of network, remote, function and delete the device. 4.5. Import Face Library Step 1: [Input personnel images in batches] After logging into the platform, click "Personnel - Personnel - Import personnel images in batches" - select pictures - "Upload" and the pictures are added into the device.
[Input personnel information in batches] When importing pictures in batches, the pictures must meet the following requirements: 1. The picture naming format can be set as: name.jpg, name_department name.jpg, name_department name_ CAUTION personnel number.jpg (the department name must exist in the system; the personnel number must be unique). 2. Ensure a clear face picture and the total size must less than 80M. Step 2: Click "Input personnel in batches - batch add people templates.
Step 3: After the gallery is added into device it can realize face recognition. CAUTION When abnormality occurs on the smart terminal platform, such as abnormal reading or abnormal data interface request, please follow the steps below: Right-click the running SDP2000 icon in the lower right corner of the desktop to check whether the status of Nignx, Mysqld, and SDP2000 is green (normal state). If any item is displayed in gray, restart the software to make it green.
4.6. Online Upgrade Prerequisites: The device is connected to the Internet. Auto online upgrade Step 1: Open the IE browser, enter "http: // device IP address: port number", such as "http://192.168.1.88", enter the login interface, enter the device default user name (admin) and password (12345).
