BOOM BOX VINYLE NOTICE / USER MANUAL
EN 2
TABLE OF CONTENTS 1. . PRESENTATION OF THE SPEAKER 1. . YOUR BO O M B O X SPE AK ER 2. . SAFETY INFORMATION 3. . WARRANTY AND REPAIR 4. . GENERAL DESCRIPTION 5. . KNOB AND CO MM AND PANEL 2. . USING THE BOOMBOX 1. . ON / OFF 2. . CHO SSIN G YOUR SO UR CE 3. . VOLUME, BASS AND TREBLE SETTINGS 4. . TURNTABLE USE 5. . USING YOUR BOOM BOX WITH YOUR DEVICES 3. . MAINTENANCE AND ASSISTANCE 1. . CLE AN IN G THE BOOM BOX 2. . NO PO W ER 3. . NO SO UN D 4. . DISTORTION OF SOUND OR BUZZING 5. .
1. DESCRIPTION OF THE BOOM BOX 1. .
2. . SAFETY INFORMATION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
WARNINGS : To reduce the risk of fire or electrical discharge, do not expose the unit to rain or wet sources. The unit is class 1 classified, and it must be connected to the electrical wall power socket with an earth plug. The unit must be installed so that it can be removed from the electrical network by means of the earth plug (or with an adapted connector located on the rear side of the unit). If the power plug is used as a disconnection device, the unit must be available and easy to use.
Low power radio wave radiating motor management method Article 12 A low-power RF motor that has passed the type approval shall not change the frequency, increase the power or change the characteristics and functions of the original design without permission. Article 14 The use of low-power RF motors shall not affect the safety of flying and interfere with legal communications; if interference is found, it shall be improved until no interference is required.
! ATTENTION The purpose of the exclamation point in equilateral triangle is to inform the user of the presence of important instructions in this manual about how to operate the device and maintenance operations. DANGEROUS VOLTAGE The luminous indicator with the “arch in an equilateral triangle” symbol is intended to warn the user of the presence of a “dangerous current” not insulated in the product, and this current could be strong enough to cause an electric discharge on people.
AERATION / IMPORTANT The unit may heat when used. Never operate the central part without its side bases. Do not place the equipment in a completely closed room or in a compartment insufficiently ventilated. Make sure that no small object can pass through the BOOM BOX. If it happens, immediately switch off the device, disconnect it from the wall power socket and contact your dealer for assistance and advice. LOCATION Carefully select a spot for installing your equipment.
CLEANING In order to clean the unit, wipe it with a dry, lint-free cloth. Do not use liquid cleaning products containing alcohol, ammonia or abrasives. Do not use a spray on and nearby the unit. REPAIRS These units should not be repaired by the user. Do not try to repair, dismount or un- assemble the unit if a problem occurs. A strong electric discharge could take place if this precautionary measures are not respected. In case of a problem or failure, please contact your dealer.
3. HERMÈS LIMITED WARRANTY 4.
BOOM BOX OPENING 1. 2. 3.
Motor pulley Vinyl arm FRONT BOOMBOX OPENED Vinyl holder Motor switch 13
ARRIÈRE 1 [ Ll jJ " c; Q J J 0 ( ( ( " (' ( ® @ @ • T RCA @ ® _rp "'_,,r ® i[E] : @ Power socket Master ON/OFF 14 ' / / n J J
5. .
2. USING THE BOOM BOX 1. . ON / OFF 1. Insert the power cord into the power socket behind your BOOM BOX. 2. Connect the power cord to the wall outlet. 3. First, Turn ON the master button at the rear of the speaker system to pre-power on the BOOM BOX speaker system. 4. Second, turn the volume knob clockwise to turn on the BOOM BOX speaker system. The Bluetooth LED lights up. VOLUME VOLUME Off Off + Standby + Standby 6.
2. . CH O O S IN G YOU R SO U R CE On your BOOM BOX, the choice of the sound source is made at the control panel by pressing one of the buttons from 1 to 4, after you have made your connections to the source panel. / Source selection BT Pair / Source selection BT / Source selection Phono / Source selection Aux matches (1) the Bluetooth® pairing with your devices. matches (2) the Bluetooth® input with your devices. marches (3) the Phono input with your devices. matches (4) the Auxiliary input.
3. . VOLUME, BASS AND TREBLE SETTINGS VOLUME SETTING TO INCREASE THE VOLUME VOLUME Turn the volume knob clockwise. TO DECREASE THE VOLUME Turn the volume knoc counter-clockwise. Off + Standby BASS SETTING BASS Vary the cursor to the - to emit less bass and to the + to emit more bass. Setting at 12h = 0: neutral position. TREBLE SETTING TREBL E Vary the cursor to the - to emit less treble and to the + to emit more treble. Setting at 12h = 0: neutral position.
4. . TURNTABLE USING 1 Positioning the belt: / With your left hand, gently hold the belt in the groove of the intended pulley. / With your right hand, stretch the pulley belt to the tray, avoiding stretching. / Gently wrap the belt around the tray without folding.
2 Select the speed according to your disc, 33 or 45 RPM by positioning the belt on the motor: 45 T OU R S 3 Unscrew the vinyl holder in the center of the tray.
4 Position the disc on the felt and make sure it is properly cleaned and dusted. And screw the vinyl holder back. 5 Remove the protection from the cartridge.
6 Start the reading by push the motor switch. 7 Take care the arm lift is up.
8 Select the Phono mode as source on the control panel. 9 Remove the arm from its support using the arm handle then carefully post it onto the disc. Drop the arm lift to ensure that the cartrighe touch the vinyl. 2 1 10 You can now read you vinyl, increase or decrease the volume, bass and treble.
11 At the end of the reading: 1 2 4 . 1 ORIENTATION OF THE CARTRIDGE In case of cell change, or if the stage has been moved, it may be necessary to adjust the orientation of the cell again. The cell head has two screws to adjust the cell angle according to the type of vinyl (33 RPM or 45 RPM). Adjustment templates are available from specialized manufacturers.
5. . US ING YOU R BOOM BOX WITH YOUR DEV ICES Your BOOM BOX is equipped with the Bluetooth® technology to play music from your computer, tablet or smartphone, without cable. The Bluetooth® receiver on your BOOM BOX lets you listen to high definition music wirelessly. To use this connection, you simply need to: 1. Turn on your BOOM BOX. 2. Bluetooth is the default source and turns on automatically. The LED on the BOOM BOX starts flashing white. 3.
3. M A I N T E N A N C E AN D AS S IS TANCE 1 . TO CL EAN THE BOOM BOX Disconnect the unit from the AC outlet before cleaning. Clean only with a dry cloth. Do not use any cleaning alcohol, or solvent to clean the surface of the device as both could damage the lacquer and cause electrical failure and fire if they penetrated the electronics of the device. Do not attempt to clean the interior of your BOOM BOX, except for the turn table. 2 . NO PO W ER Make sure that the cable is securely connected.
5 . BA C K G R O U ND NOIS E AND UNW ANTED IN T E R FE R E NC E Remove other electrical equipment that may cause interference. In case the above solutions do not remedy your problem, please contact a professional. For any repairs, during or after the warranty, please contact your dealer. 6 . TH E RM A L PR O T EC T IO N OF THE AM PL IE R In the case of prolonged use at a high level of listening, a significant temperature rise may affect the amplifier’s performance.
8 .
