Bed Liner Kit Model No.: HCL1B8 HCL1G8 Application Instructions ¿Habla español? Vea página Parlez-vous français? Voir page 1 1 Read these instructions completely before using this product. Retain these instructions for future reference.
CONTENTS SAFETY PRECAUTIONS................................................................................................................. 2 GENERAL INFORMATION............................................................................................................... 3 BED SURFACE PREPARATION...................................................................................................... 3 APPLYING LINER TO TRUCK BED.................................................................................
• Make sure to prepare the surface properly before applying the Herculiner material. A surface that is not correctly prepared may not allow the material to adhere properly. GENERAL INFORMATION HERCULINER Brush-on Bed Liner is a polyurethane-based product that is designed to be easily applied to any truck bed with great results. It is important that you follow the application instructions as closely as possible.
7. Blow out or wipe down the truck bed and tailgate, removing all excess sanding dust. Before using any solvents, always read and comply with the solvent manufacturer’s recommendations for proper use and handling of solvents. 8. Wipe down the truck bed and tailgate with xylene (Xylol), acetone or MEK solution, and a rag (it is recommended to wear rubber gloves while working with any solvents and when applying HERCULINER). 9. Allow xylene (Xylol), acetone or MEK to dry completely (about 10 minutes).
9. Apply a second coat of HERCULINER to the taped seam just before the first coat dries. This will enable the tape to be removed without tearing. If tape sticks to HERCULINER, run a razor along the taped edge. 10. Repeat the application process for the second coat (steps 4-7). 11. Areas can be touched up with a small brush and unwanted HERCULINER can be removed with xylene (Xylol), acetone or MEK solution while it is still wet. 12.
For best results, old concrete should: • Be completely dry before application of HERCULINER. • Be thoroughly cleaned with a muriatic acid wash. 1. Use 45% to 50% muriatic acid solution. 2. Agitate the solution on the surface with a hard-bristled deck brush. 3. Rinse off with 5% ammonia/water solution. 4. Dry completely. 5. Brush off residue. • Be wiped with xylene (Xylol), acetone or MEK cleaning solvent. Allow solvent to dry completely before applying HERCULINER.
Fiberglass Good adhesion can be obtained on unweathered gel-coated glass, rough fiber, side molded glass and smooth-mold resin-side glass. The surface should be free of oils, waxes and other production additives, and then sanded to remove all gloss, leaving a rough surface. GENERAL APPLICATION HERCULINER may be applied with a brush, roller or spray gun. A roller will provide the roughest final texture; a spray gun will provide the least texture.
PRODUCT CURING INFORMATION • Normally, HERCULINER can be subjected to light foot traffic within 12 hours and should not be subjected to cleaning or chemical exposure until fully cured, in 3-5 days (approximately 96 hours – slightly longer for gray HERCULINER). • HERCULINER takes about 4 days to fully cure: less time in hot humid conditions, and more time in cold dry weather. Full curing time only affects the amount of time required to wait before subjecting the surface to cleaning and chemical exposure.
CARE AND MAINTENANCE OF HERCULINER SURFACES For best results, use a stiff-bristled deck brush to agitate cleaner on the surface. (A cotton mop is not recommended since pieces of mop may get caught on high profile HERCULINER surface. A synthetic fiber material mop may be used if a deck brush is unavailable.) 1. Use any general floor cleaner, from a neutral commercial cleaner to a household cleaner, or its equivalent. 2. Rinse the surface thoroughly to remove all residue. 3.
WARRANTY OLD WORLD INDUSTRIES, LLC warranties this product against faulty manufacture and defective materials. OLD WORLD INDUSTRIES, LLC will not accept product liability for application or use of this product. For additional technical assistance contact: HERCULINER 4065 Commercial Avenue Northbrook, IL 60062 Toll-free: 1-800-477-5847 Fax: 1-847-559-2021 www.herculiner.
