Instructions / Assembly

Henry Company 999 N. Sepulveda Blvd., Ste. 800, El Segundo, CA 90245
Technical Services - Phone: [phone]
E-mail: [e-mail] www.Henry.com
Rev. Date: 03/03/2015
887HS TROPI-COOL® 100% SILICONE WHITE ROOF COATING – HIGH SOLIDS
atmosphere may form a skin on the surface. If this occurs, simply remove the skin, mix the product, and use the rest. It should be applied at
approximately 100 square feet per 1.5 gallons. Dry film thickness (DFT) should be a minimum of 22 mils. On rougher surfaces, an additional
coat may be required to get a uniform, consistent thickness over the entire roof surface. Coating must be evenly applied and pin-hole free. If
applying an additional coat, wait a minimum of 2 to 6 hours (but no longer than 48 hours) for each coat to fully cure (dependent on weather
conditions, such as temperature and humidity) before applying additional coats. Apply subsequent coats perpendicular in fashion to the
previous coat. For example, apply 1
st
coat north and south; apply 2
nd
coat east and west. Polyurethane foam should be coated within 24
hours of application.
Please consult Henry Product Support for any specific questions regarding the application of this product.
Clean-up
Clean-up of spray equipment containing uncured material may be accomplished by flushing with VM&P Naphtha or mineral spirits. This
product cures by reacting with moisture and should not be left in spray guns, pump equipment, and hoses for prolonged periods unless
equipment contains moisture lock hoses, fittings, and seals. Equipment without these components will transmit sufficient moisture vapor to
gradually form cured material on hose walls and at unsealed connections potentially causing an increase in operating pressure and material
flow restriction.
Precautions
DO NOT THIN. Keep away from food. Not recommended for application at temperatures below 35°F (2°C) or if rain is expected in less than 1
hour of application. Lower temperatures and/or less humidity will typically result in slower cure times. When transporting, make sure the pail
is secured and the lid is tight to prevent spills. Store in a cool, dry, shaded location. Ensure lid is completely sealed.
This product is not recommended for interior use. Building occupants should be warned of spray operations in process. Installers should
exercise caution during spray processes to avoid falls caused by stepping into slippery wet coating. Installers should read and understand all
technical and informational literature on this product, prior to use of the product.
Warning
Causes skin irritation. Causes serious eye irritation.
Prevention: Wash thoroughly after handling. Wear protective gloves and eye protection.
Response: IF ON SKIN: Wash with plenty of soap and water. If skin irritation occurs; Get medical advice or attention. Take off contaminated
clothing and wash it before reuse. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: Get medical advice or attention.
Storage: Store in a well-ventilated place.
Disposal: Dispose of contents/containers in accordance with local/regional/national/international regulations.
See safety data sheet for further details regarding the safe use of this product.
KEEP OUT OF REACH OF CHILDREN.
FOR EXTERIOR USE ONLY.
PLEASE READ THE ENTIRE LABEL.
Limited Product Warranty
We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product
– such as weather, workmanship, equipment utilized, and prior condition of the substrate – are all beyond our control; therefore, Henry
Company cannot guarantee results of the application of the coating including, but not limited to: appearance, watertightness, and suitability
of the substrate. The substrate to be coated must be structurally sound and have reasonable life expectancy prior to being coated. We will
replace at no charge any product proved to have a material defect during the life of the existing roof, provided it has been applied in
accordance with our written directions for uses we recommended as suitable for this product. Proof of purchase must be provided. This
warranty is void if the coating is coated over, patched, painted, or covered in any way with any product other than this coating or approved
products. DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY: THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES
EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR