TDS

Henry
®
Company, 999 N. Sepulveda Blvd., Ste. 800 El Segundo, CA 90245
Tel: [phone] Email: [e-mail]
www.henry.com
Revision Date: 09/25/2017
880 Tropi-Cool
®
100% Silicone Stop Leak
®
Spray Sealer (clear)
minutes and is fully cured in 8 hours (dependent on weather conditions, such as temperature and humidity). Shake can occasionally
throughout application. Avoid spraying in windy conditions. Protect surrounding area from overspray. Not recommended if rain is
expected in less than 15 minutes of application. Lower temperatures and/or less humidity will typically result in slower cure times.
Clogging: This product is meant to be completely used within 8 hours from initial use. After use, invert the can and press spray
nozzle to clear out residual product. For additional use within 8 hours, spray a quick burst on a test area to un-lodge any cured
material from valve stem. If necessary, unscrew nozzle and pull out plug of cured material from the nozzle/stem. Once removed,
screw nozzle back on and continue spraying the sealer. Do not strike the can.
Note: Product is non-tintable and non-paintable. For best results ensure that the can has been stored at 50 °F to 100 °F (10 °C to
38 °C) prior to spraying.
Coverage
Up to 15 sq. ft. per canister at approximately 5 mils DFT. Coverage rate is theoretical and does not take into account for material
loss due to spraying, surface texture, etc.
Clean-up
Use VM&P Naphtha or mineral spirits. Read solvent Safety Data Sheets before use. Keep cleaning solvents away from all sources
of heat, sparks, flame, lighted smoking materials, or any other ignition source.
Limited Product Warranty
LIMITED PRODUCT WARRANTY: We, the manufacturer, warrant only that this product is free of defects, since many factors which
affect the results obtained from this product - such as weather, workmanship, equipment utilized and prior condition of the substrate
- are all beyond our control; therefore, Henry Company cannot guarantee results of the application of the coating including, but not
limited to: appearance, watertightness, and suitability of the substrate. The substrate to be coated must be structurally sound and
have reasonable life expectancy prior to being coated. We will replace at no charge any product proved to have a material defect
during the life of the existing roof, provided it has been applied in accordance with our written directions for uses we recommended
as suitable for this product. Proof of purchase must be provided. This warranty is void if the coating is coated over, patched, painted,
or covered in any way with any product other than this coating or approved products. DISCLAIMER OF WARRANTIES AND
LIMITATION OF LIABILITY: THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. MANUFACTURER SHALL HAVE NO LIABILITY OF ANY KIND BEYOND PRODUCT REPLACEMENT, INCLUDING
FOR CONSEQUENTIAL, EXEMPLARY OR INCIDENTAL DAMAGES RESULTING FROM ANY DEFECTS OR ANY DELAYS
CAUSED BY REPLACEMENT OR OTHERWISE. IF PURCHASER DOES NOT ACCEPT THESE TERMS OF HENRY'S LIMITED
WARRANTY, PURCHASER MAY RETURN WITHIN 30-DAYS OF PURCHASE ALL CONTAINERS OR PACKAGES OF
PRODUCT PURCHASED FOR A FULL REFUND (PROVIDED THE CONTAINERS OR PACKAGING IS UNOPENED AND LESS
SHIPPING CHARGES IF ANY). RETENTION OF PRODUCT BEYOND 30-DAYS FROM PURCHASE, OR USE OF PRODUCT
SHALL CONSTITUTE ACCEPTANCE OF HENRY'S LIMITED WARRANTY TERMS, CONDITIONS AND DISCLAIMERS. THIS
LIMITED WARRANTY PROVIDES THE PURCHASER'S EXCLUSIVE REMEDY FOR ANY DEFECT IN THE PRODUCT. To the
extent that any part of this LIMITED PRODUCT WARRANTY AND LIABILITY DISCLAIMER is determined unenforceable under the
law of the place of purchase of the product, that part is severed and the remainder of these terms remain in full force and effect. To
the extent permitted by law, the duration of any implied warranties is limited to the duration of Henry’s express warranty.
For more information, visit www.henry.com or for technical assistance call us at 800-486-1278. For more information on Henry’s
®
product warranty and liability disclaimer
please visit www.henry.com/warranty. Refer to the Safety Data Sheet prior to using this product. The Safety Data Sheet is available at www.henry.com or by emailing
Henry
®
Product Support at [e-mail] or by calling 800-486-1278.
Henry, Tropi-Cool and Stop Leak are registered trademarks of Henry Company
The technical and application information herein is based on the present state of our best scientific and practical knowledge. As the information herein is of a general
nature, no assumption can be made as to a product’s suitability for a particular use or application and no warranty as to its accuracy, reliability or completeness either
expressed or implied is given other than those required by law. The user is responsible for checking the suitability of products for their intended use. Henry
®
Company
data sheets are updated on a regular basis; it is the user’s responsibility to obtain and to confirm the most recent version. Information contained in this data sheet may
change without notice.