Newtec Point&Play™ Setup Manual Version 1.
Contents Contents 1 Introduction .................................................................... 4 2 Setting up the antenna .................................................. 11 About this guide........................................................................... 4 Safety precautions........................................................................ 5 Material provided in the box.......................................................... 7 Material you need to provide yourself ..........
HELLAS SAT Point&Play Manual - page 3 Version 1.
Introduction 1 Introduction About this guide This guide provides a step-by-step procedure to install the HELLAS SAT terminal (consisting of the antenna and the IPmodem).
Introduction Safety precautions This section lists the safety precautions to follow when installing the antenna. Safety precautions are grouped into warnings and cautions. Local regulations Always install the HELLAS SAT antenna in accordance with local regulations. Warnings A warning refers to an action or situation that could result in injury, long term health hazard or death if you do not follow the instructions.
Introduction Cautions A caution refers to an action or situation that could result in equipment damage or destruction if you do not follow the instructions. IPmodem - Always use the in-line power supply with the IPmodem. Using a different power supply may cause equipment damage. - To ensure regulatory and safety compliance, use only the provided power and interface cables or cables which conform to the specifications within this manual. - Do not open the unit.
Introduction Material provided in the box 1 1x 2 2x 3 2x 4 1x 6 2x 9 1x 7 1x 20 mm 12 1x 10 1x 11 4x 50 mm 5 1x 8 4x 13 1x 8 mm 18 1x 14 1x 19 1x 20 1x 21 1x 16 mm 15 4x 6 mm 16 7x 17 1x 22 1x 23 1x HELLASSAT Point&Play Setup Manual - page 7 Version 1.
Introduction Material provided in the box: list Number on figure Item Quantity 1 Masthead 1 2 Brackets 2 3 Pole clamps 2 4 iLNB clamp 1 5 iLNB (Interactive Low Noise Block downconverter) 1 6 Screw 50 mm M6 2 7 Screw 20 mm M6 1 8 Screw 16 mm M6 4 9 Hex key 1 10 Cap 1 11 F-connectors 4 12 Parker Screw 1 13 Feed arm 1 14 Satellite dish 1 15 Nut M8 4 16 Nut M6 7 17 Grounding nut 1 18 Headphone 1 19 Point&Play™ Tool 1 20 IPmodem 1 21 Coax cable 1
Introduction Material you need to provide yourself - A solid base for the antenna; - An antenna pole; - A Phillips head screwdriver PZ2; - Open-end spanners of 10, 11 and 13mm; - Tie-wraps; A cutter; A compass; A spirit level; A grounding cable; This cable needs to meet the following specifications: UL style 1007/1569, PVC insulated, 300V, 80°C (C.S.A. Type TR-64) 18AWG, Yellow/Green attached to 4,3 mm insulation and 5,0 mm non-insulation supported ring terminal.
Introduction Installation overview The image below shows the results of a typical installation as described in the following pages. Please read these pages carefully to perform the installation. Satellite Power supply with adapter iLNB IPmodem Antenna Rx cable Tx cable Ethernet cable Version 1.
Setting up the antenna 2 Setting up the antenna Assuming you already have a solid base (made of concrete, or firmly attached to a wall), installing the antenna includes the following steps: Step 1 - Choosing a suitable location (page 12) Step 2 - Mounting the antenna pole (page 13) Step 3 - Mounting the antenna (page 14) Step 4 - Fixing the antenna cabling (page 21) Step 5 - Pointing the antenna (page 29) HELLASSAT Point&Play Setup Manual - page 11 Version 1.
Setting up the antenna Step 1 - Choosing a suitable location Outdoors: antenna - When setting up the antenna base, take account of the orientation the antenna must have. Orientation data are available in the Antenna Pointing Information document. - The antenna needs a clear view towards the satellite (without any buildings, trees... that may hinder the signal). - To connect the antenna to the IPmodem, you will use coax cable. You can use the provided coax cable or a coax cable with the same specifications.
Setting up the antenna Step 2 - Mounting the antenna pole When fixing the antenna pole on the base, use a spirit level to make sure the antenna pole stands upright. HELLASSAT Point&Play Setup Manual - page 13 Version 1.
Setting up the antenna Step 3 - Mounting the antenna 1 Insert the 2 brackets in the masthead (as shown). 2 Use the 2 pole clamps and nuts to attach the masthead to the pole. - If the pole is low enough, you can first assemble the masthead, brackets and clamps and slide the assembly over the antenna pole. - If the pole is too high or does not have an open ending, you will have to fix the masthead around the pole.
Setting up the antenna - Make sure the masthead is already pointing in the general direction of the satellite. To do so, use the pointing data available in the Antenna Pointing Information document. - Make sure to attach the masthead upright to the pole. HELLASSAT Point&Play Setup Manual - page 15 Version 1.
Setting up the antenna 3 Attach the dish to the masthead with the appropriate screws and nuts. Version 1.
Setting up the antenna 4 Insert the feed arm in the cut-away at the bottom of the dish and fix the arm with the appropriate bolts. HELLASSAT Point&Play Setup Manual - page 17 Version 1.
Setting up the antenna 5 Attach the clamp around the iLNB using the appropriate nut and bolt. Do not to attach the clamp too tightly as you will need to adjust it later on. Version 1.
Setting up the antenna 6 Slide and click the iLNB clamp into the feed arm. HELLASSAT Point&Play Setup Manual - page 19 Version 1.
Setting up the antenna The antenna is mounted. The result should look like the figure below. Version 1.
Setting up the antenna Step 4 - Fixing the antenna cabling Fixing the antenna cabling includes the following steps: - Connecting the F-connectors on the coax cable (page 22) - Grounding the iLNB (page 24) - Adjusting iLNB polarisation (page 25) - Connecting the iLNB to the IPmodem (page 27) - Connecting the IPmodem to your computer (page 28) HELLASSAT Point&Play Setup Manual - page 21 Version 1.
Setting up the antenna Connecting the F-connectors on the coax cable You will need a cutter (and possibly pliers) to connect the F-connectors. To connect an Fconnector to a cable: 1 For the outdoor end of the cable, first slide the rubber boots over the coax cable. outside use 2 Strip the coax cable as shown below. Do not remove the aluminium foil or fold it back. 1,4cm 3 Fold the wire shielding backwards over the cable jacket. 4 Cut away the plastic shield.
Setting up the antenna 5 Screw the F-connector to the wire by hand. 0,4cm 1cm Repeat this procedure for all 4 F-connectors. HELLASSAT Point&Play Setup Manual - page 23 Version 1.
Setting up the antenna Grounding the iLNB As you will use the antenna for internet access, you need to ground the antenna. To do so, you need a grounding wire (for grounding wire specifications, see page 9) and a bolt fitting the grounding connection on the masthead. The iLNB has a stud that you can use to ground it. To ground the iLNB: 1 Connect the grounding wire to the stud on the iLNB. 2 Connect the wire to the grounding connection on the masthead. Rx Version 1.
Setting up the antenna Adjusting iLNB polarisation Polarisation of the iLNB allows correct data reception and transmission. To adjust iLNB polarisation: 1 Check the scaling on the iLNB.
Setting up the antenna 2 3 4 In the Antenna Pointing Information document, look up the value that applies to the city closest to your position. Set the iLNB to the angle you have found in the document. Lock the iLNB in the clamp with the securing bolt available on the iLNB. Version 1.
Setting up the antenna Connecting the iLNB to the IPmodem To connect the iLNB (Interactive Low Noise Block downconverter) to the IPmodem: 1 Identify the cables marked RX and TX on the coax cables (these marks are printed on the cables every 50 cm). 2 Put the TX and RX connectors in the appropriate RX and TX jacks on the iLNB. The outdoor connections need to be waterproof. Make sure to use the outdoor connectors (with rubber boots) for the iLNB.
Setting up the antenna Connecting the IPmodem to your computer 1 2 Plug the network cable in the IPmodem’s and your computer’s ethernet ports. You can use the network cable provided in the box or a cable of your choice. Use the power adapter provided in the box to connect the IPmodem to a wall outlet. The result should look like the figure below. DC 15V LAN iLNB TX iLNB RX RESET to antenna Version 1.
Setting up the antenna Step 5 - Pointing the antenna Pointing the antenna includes the following steps: - Setting the IPmodem software to pointing mode (page 30) - Using the Point&Play™ Tool (page 32) - Setting up the Point&Play™ Tool (page 33) - Rough pointing: vertical (elevation) (page 34) - Rough pointing: horizontal (azimuth) (page 36) - Fine-pointing the antenna (page 39) - Checking the antenna pointing (page 42) - Finishing installation (page 43) - Confirming antenna pointing in the software (page 4
Setting up the antenna Setting the IPmodem software to pointing mode Before you start The procedure below assumes: - that your computer is DHCP enabled; - that you will connect a single computer to the IPmodem. If this is not the case or if you have another configuration, you will find more information in the Termincal User manual on the cd, in Appendixes Local Network Configuration and Changing your IP settings. Before fine-pointing the antenna, you need to access the status page of the IPmodem.
Setting up the antenna - If the satellite has only one pointing carrier, you will see the page below. 5 Click the Start Pointing button. You can now start pointing the antenna. Note Whenever you redo the pointing procedure and access the IPmodem software, the button will be labelled Restart Pointing instead of Start pointing. HELLASSAT Point&Play Setup Manual - page 31 Version 1.
Setting up the antenna Using the Point&Play™ Tool The Point&Play™ Tool will help you point the antenna correctly. During the pointing procedure, the Point&Play™ Tool can produce various sounds, each having a specific meaning described below. You will thus need to put on the headphone whenever needed during the pointing procedure. Ensure that the volume of the Point&Play™ tool is not set too loudly, otherwise damage to your hearing may occur.
Setting up the antenna Setting up the Point&Play™ Tool To 1 2 3 set up the Point&Play™ Tool: Remove the TX connector from the iLNB and connect it to the Point&Play™ Tool. Connect the headphone to the appropriate port of the Point&Play™ Tool. Make sure the Point&Play™ Tool is turned on and the volume is high enough. LAN DC 15V iLNB iLNB TX RX Rx Tx RESET HELLASSAT Point&Play Setup Manual - page 33 Version 1.
Setting up the antenna Rough pointing: vertical (elevation) Important notes - The procedures relating to rough horizontal and vertical pointing are described below in a sequential way. In reality, you will have to perform these two procedures simultaneously. - Whenever the procedure tells you to loosen a securing bolt or nut, slacken it just enough to allow the corresponding element to move freely.
Setting up the antenna 2 Loosen securing bolts (1) and (2). 10 1 20 E E 30 40 50 60 3 2 3 3 4 5 Use the hex key to rotate the eccentric E (3) until the letters E on the eccentric and the masthead point towards each other, as shown in the figure above. While keeping the eccentric E in this position (with the hex key), set the dish to the elevation you found in the document. Bolt (2) indicates the elevation. In the figure above, the elevation is set to 49°.
Setting up the antenna Rough pointing: horizontal (azimuth) 3 A A To start horizontal pointing: 1 Loosen the lock bolts (1) and (2) of the eccentric A (3). 1 4 2 2 3 4 Rotate the eccentric (3) with the hex key until the letters A on the eccentric and the masthead point towards each other, as shown in the figure above. Secure the lock bolts (1) and (2). Loosen the bracket nuts (4). You can now move the antenna horizontally.
Setting up the antenna Azimuth 4 5 6 Slowly move the dish horizontally until you hear the highest possible continuous pitch tone. Make sure to position the antenna in the middle of this tone range. As soon as you hear this continuous high pitch tone, secure the bracket nuts (4). It is recommended not to secure the eccentric A (as you may damage it by doing so). HELLASSAT Point&Play Setup Manual - page 37 Version 1.
Setting up the antenna Persistent low pitch If you keep hearing a low pitch tone, this might indicate one of the following issues: - Check if you have a clear line of sight, and no building, tree or other obstruction is blocking the path between the antenna and the satellite. Select a place with clear line of sight to set-up the antenna. - The pointing carrier selected in the IPmodem status page is not correct. If so, on the IPmodem status page on your computer: - Click Pointing completed.
Setting up the antenna Fine-pointing the antenna If you do not hear a continuous high pitch tone after securing the bolts, the antenna will probably have moved slightly. You then need to fine-point the antenna. Important note The procedures relating to vertical and horizontal fine-pointing are described below in a sequential way. In reality, you will have to perform these procedures simultaneously. HELLASSAT Point&Play Setup Manual - page 39 Version 1.
Setting up the antenna Fine-pointing: vertical 1 Loosen bolt (1). 10 1 20 E E 30 40 50 60 3 2 4 3 2 3 4 Rotate the eccentric (3) until the Point&Play™ Tool produces a continuous high pitch tone. Secure bolt (1). Place the cap (4) on bolt (2) and secure it with the appropriate nut. Version 1.
Setting up the antenna Fine-pointing: horizontal A Loosen the horizontal lock bolt (1) and (2). 3 A 1 1 4 2 2 3 Rotate the eccentric (3) until the Point&Play™ Tool produces a continuous high pitch tone. Secure the horizontal lock bolts (1) and (2). HELLASSAT Point&Play Setup Manual - page 41 Version 1.
Setting up the antenna Checking the antenna pointing Perform the following checks to make sure the antenna will resist external movements (wind...): 1 Make sure all bolts are tightly secured. 2 Shortly place your hand between the iLNB and the dish. As soon as you remove your hand, you should hear the continuous high pitch tone again. 3 Exert some pressure on the antenna to make the edges move about 3 cm on the left hand side, right hand side and at the top, then release it.
Setting up the antenna Finishing installation 1 2 3 4 When pointing is completed, you can turn off the Point&Play™ Tool. Remove the Tx cable from the Point&Play™ Tool and connect it to the iLNB. Slide the rubber boots over the connectors. Use tie-wraps to attach the cables to the feed arm. Make sure to leave some slack on the cables. The result should look like the figure below. Rx HELLASSAT Point&Play Setup Manual - page 43 Tx Version 1.
Setting up the antenna Confirming antenna pointing in the software 1 Back to your computer, in the status page of the IPmodem, click the Pointing Completed button. You are now ready to surf the internet. Version 1.
