User manual Dominus 10SC V2
IKONNIK XENON HRS3.2 STANDARD OPERATION
RADIENT REAKTOR 50-4 BRUSHLESS SYSTEM OVERVIEW...
8
› From pulled back: the vehicle will apply brakes to slow the speed.
» A second push forward of the trigger will apply brakes again.
» A second push forward on the trigger will apply reverse throttle.
» WARNING: Causing the vehicle to make quick transitions from forward/reverse motion to the opposite direction
using the throttle control can cause damage to your vehicle and electronics and will void the warranty.
Using your transmitter for the first time:
1. Turn the transmitter ON and ensure the LED is lit SOLID and it is not giving
an audible alarm indicating the batteries are supplying adequate voltage for
proper operation.
2. Ensure the battery in your vehicle is secured, charged and plugged in with
proper polarity and turn your vehicle ON.
3. Checking and setting the throttle trim.
a. If the wheels spin in a forward direction when the trigger is in the neu-
tral position, turn down the trim until the motor stops by pressing the
TH- button, repeatedly if necessary.
b. If the wheels spin in a reverse direction when the trigger is in the neu-
tral position, turn up the trim until the motor stops by pressing the TH+
button, repeatedly if necessary.
c. There will be a “dead band” area where the trim can be adjusted a
slight amount in either direction and the wheels will not begin to move.
It is ideal to have the trim set in this region.
4. Setting the steering trim.
a. With your vehicle and transmitter turned on (and properly responding to transmitter inputs), set the vehicle down on the
ground and slowly accelerate in a direction directly away from you. If the vehicle veers slightly either to the left or right,
adjust the steering trim by pressing either the ST- (more left) or ST+ (more right) buttons, repeatedly if necessary.
b. Reset the vehicle position and re-test; adjust the trim as needed until the vehicle travels in a straight line while the transmit-
ter wheel remains at center location (“hands-off”).
The Radient Reaktor series brushless motor and ESC is a great power plant to satisfy your need for speed and performance as an
entry level brushless system. Though the Reaktor system was engineered for value, performance was definitely a factor. We’ve
included some great features for you to help keep your system running in top shape while keeping your battery upgrade path open
since it is compatible with LiPo batteries.
WARNING: ALWAYS ALLOW YOUR MOTOR TO COOL BETWEEN RUNS. EXCESSIVE ACCELERATION AND AGGRESSIVE DRIV-
ING WILL CAUSE YOUR SYSTEM TO GET HOT. EXCERCISE GREAT CARE WHEN HANDLING YOUR VEHICLE AFTER RUNNING TO
AVOID GETTING BURNED.
Some great features of your new ESC include:
• Water-proof and dust-proof. The ESC can work under water for a short time.
› (Please remove the cooling fan when running car in water, and after run-
ning, please make the ESC clean and then dry it to avoid oxidation of the
copper connectors)
• Specially designed for RC car and truck, with excellent start-up, acceleration
and linearity features.
• Compatible with sensorless brushless motors.
• 2 running modes suitable for different applications (“Forward with brake”
mode, “Forward/Backward with brake” mode).
• Proportional ABS brake function with 4 steps of maximum brake force ad-
justment, 8 steps of drag-brake force adjustment.
• 4 start modes (“Punch”) from “Soft” to “Very aggressive” to be suitable for
different chassis, tires and tracks.
• Multiple protection features: Low voltage cut-off protection for Lipo or
NiMH battery / Over-heat protection / Throttle signal loss protection / Motor
blocked protection.
• Easily programmed with the “SET” button on the ESC or with the LED Program Card.
F
B
RL
Brake
Throttle Reverse
Turn Right
Throttle
Forward
Turn Left
F
B
L R
ESC TECHNICAL SPECIFICATIONS
Continuous Current 50A
Burst Current 220A
Resistance 0.0012 ohm
Motor Type Sensorless
Motor Limit 3650kV
Battery
NiCd/NiMH 4-9 cells
LiPo 2-3s
BEC 6V/1A (Linear Mode)
Program Port Use cooling fan port
Dimensions 48.5mm x 38mm x 32mm
Weight 90g