FORCED AIR PROPANE HEATER Model#: SRCH11011 (35,000~55,000Btu/hr) Model#: SRCH11033 (85,000~125,000Btu/hr) Model#: SRCH11011 3194320 Model#: SRCH11033 WARNING: NOT FOR HOME OR RECREATIONAL VEHICLE USE. Owner’s Manual Standard: Conforms To ANSI Z83.7b-2009/CSA 2.
I GENERATES 2
TABLE OF CONTENTS Safety Information............................................................................................ 2 Unpacking........................................................................................................5 Specifications.......................................................................................................6 Wiring Diagram ... ..................................................................................................7 . Propane Supply ...........
SAFETY INFORMATION CONTINUED The heater is designed for use as a construction heater in accordance with ANS Z83.7b-2009/CSA2.14b-2009. Other standards govern the use of fuel gases and heating products for speci c uses. Your local authority can advise you about these. The primary purpose of construction heaters is to provide temporary heating of buildings under construction, alteration or repair. Properly used, the heater provides safe economical heating.
SAFETY INFORMATION CONTINUED 8. Do not use heater in a basement or below ground level. Propane gas is heavier than air. If a leak occurs, propane gas will sink to the lowest possible level. 9. Keep appliance area clear and free from combustible materials, gasoline, paint thinner and other flammable vapors and liquids. Dust is combustible. Do not use heater in areas with high dust content. 10.Minimum heater clearances from combustible materials: Outlet: 8 Ft. (2.4 m), Sides: 2 Ft. (0.6 m),Top: 6 Ft. (1.
SPECIFICATIONS Model No SRCH11011 SRCH11033 Gas Consumption 35 ,000~55,000Btu/Hr 85, 000~125, 000Btu /hr Gas Consumption 1. 62~2. 55 LBS/Hr 3. 96~5. 72 LBS/Hr Fuel Propane Propane Supply Pressure (To Regulator) Maximum:Cylinder Pressure Maximum:Cylinder Pressure Minimun: 5PSI Minimun: 5PSI Regulator Outlet Pressure 11" W. C . 20" W.C.
WIRING DIAGRAM(SRCH11011) (AC110-120V) WIRING DIAGRAM(SRCH11033) (AC110-120V) 7
Propane gas and propane tank(s) are to be provided by the user. Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the ANSI/NFPA58. Your local library o re department will have this booklet. The amount of propane gas ready for use from propane tanks varies. Two factors decide this amount: 1. The amount of propane gas in tank(s) 2. The temperature of tank(s) The cylinder and tank quantity relys on envionment and temperature variables Model No.
ILLUSTRATED PARTS BREAKDOWN (MODEL NO.
PART LIST(MODEL NO.
ILLUSTRATED PARTS BREAKDOWN(MODEL NO.
PART LIST(MODEL NO.
FLAME 4. Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess- ow check valve on propane tank may stop ga ow.If this happens,close propane supply valve and open again slowly. 5. Check all connections for leaks. 6. Close propane supply valve.
INSTALLATION Propane Supply Valve Hose Propane Tank POL Fitting Regulator Connecting Regulator To Propane Tank NOTE: To install or dismantle hose and regulater, please use wrench to tighten the inlet connector.
INSTALLATION(MODEL NO.SRCH11011) 1. Install handle (3) and handle support (2) with 4 self-tapping screws on the top surface of heater as diagram. Self-tapping screw 2 3 2. Insert the knob (31) and make sure the “OFF” position is matchable as diagram.
INSTALLATION(MODEL NO. SRCH11033) 1. Attach the lift control knob (37) to the position with 1 M4X8 bolt. 37 M4x8 bolt 2. a) Install handle (2) and handle support (1) 4 with self-tapping screws on the top surface of heater as diagram. b) Insert the knob (40) and make sure the “OFF” position is matchable shown in diagram. 1 2 40 3. a) Unscrew 4 M5X10 bolts from the left & right supports (42). b) Divide the left & right supports (42) and reinstall them as illustrated, to enhance the product stability.
SAFETY CHECK WARNING : ONLY AN AUTHORIZED GAS TECHNICIAN SHOULD INSTALL THIS PRODUCT. CHECK FOR LEAKS All connection on this heater have been checked for leakage at the factory. Follow these steps to check regulator/pressure adjustment valve/cylinder connections before operating: 1) Make leakage solution by mixing 1 part liquid dish soap and 3 parts water.
VENTILATION WARNING: Follow the minimum fresh, outside air ventilation requirements. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater. OPERATION WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater. BEFORE START HEATER 1. 2. 3.
OPERATION MODEL NO.SRCH11011 TO START HEATER (MODEL NO.SRCH11011) 1. Connect power cord to a properly grounded three(3) prong AC110-120V, 60Hz, single phase receptacle. 2. Motor will start and fan will turn, forcing air out from the heater. 3. Turn the control knob (31) clockwise to OFF position. 4. Turn on propane tank valve slowly, and wait fifteen(15) seconds to clear any gas. Check the gas connection with a soap or water solution, or if you don't smell gas, go to next step.
OPERATION MODEL NO.SRCH11033 TO START HEATER (MODEL NO.SRCH11033) 1. Connect power cord to a properly grounded three (3) prong AC110-120V, 60Hz, single phase receptacle. 2. Motor will start and fan will turn, forcing air out from the heater. 3. Turn the control knob clockwise to OFF position. 4. Turn on propane tank valve slowly, and wait fifteen(15) seconds to clear any gas. Check the gas connection with a soap or water solution, or if you don't smell gas, go to next step.
5. When the heater is to be stored indoors, the connection between the propane supply cylinder(s) and the heater must be disconnected and the cylinder(s) removed from the heater and stored in accordance with Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 and CSA B149.1, Natural Gas And Propane Installation Code.
MAINTENANCE WARNINGS Never service heater while it is plugged in, connected to propane supply, operating or hot. Severe burns and electrical shock can occur. Keep heater clear and free from combustible materials, gasoline and other flammable vapors and liquids. Do not block the flow of combustion or ventilation air. 1. Keep heater clean. Clean heater annually or as needed to remove dust and debris. If heater is dirty or dusty, clean heater with a damp cloth. Use household cleaners on difficult spots. 2.
TROUBLESHOOTING WARNING: Never service heater while it is plugged in, connected to propane supply, operating or hot. Severe burns and electrical shock can occur. Fan does not turn when heater is plugged in 1. No electrical power to heater 2. Fan hitting inside of heater shell ed by qualifi 3. Switch broken ( used for SRCH11033) Heater shuts down while running 3. replace switch ( used for SRCH11033) 1. Provide a full tank.
REPLACEMENT PARTS WARNING: Use only original replacement parts. This heater must use design-specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries.This will also protect your warranty coverage for parts replaced under warranty. PARTS UNDER WARRANTY Contact authorized dealers of this product. If they can' t supply original replacement part(s), either contact your nearest Parts Central or call SHINERICH customer service Toll Free No.
