Installation and Operation Manual

ManualsBrandsHeat-Timer ManualsElectronicsDTS

059049-00 Rev. '

Wireless Space Sensor

Wireless 1HWZRUN6HQVRU6\VWHP

CAUTION

This equipment complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. If this equipment does cause harmful interference to radio or television reception, which can be etermined, by turning this

equipment OFF and ON, the user may correct the interference by: (1) Reorienting or relocating the receiving antenna, (2) Increasing

separation between the equipment and wireless components, (3) Connecting the equipment to a different outlet circuit from that of the

wireless components, or (4)Consulting an experienced radio/TV technician for assistance.

The antenna supplied by Heat-Timer Corporation must be used (gain <= 6dB). It is recommended not to operate the device (transceiver)

with persons closer than 20cm to the antenna. Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

Summary of content (12 pages)

PAGE 1
Installation and Operation Manual Wireless Space Sensor Wireless 1HWZRUN 6HQVRU 6\VWHP CAUTION This equipment complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 2
Wireless SNR Installation and Operation Manual Contents Controls, Indicators, and Connections. . . . . . . . . . . . . . . . . . . . . 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Required Materials (Not Supplied) . . . . . . . . . . . . . . . . . . . . . 5 Programming the System ID . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
Controls, Indicators, and Connections 3 Controls, Indicators, and Connections Figure 1: Wireless Space Sensor Controls, Indicators, and Connections 1 2 3 4 6 5 Item 1 Description Mode Button Item Description 4 Internal Antenna 5 Batteries Use to set the Wireless SNR mode (Normal, Install, or One Packet). 2 Status Indicators (LEDs) • Red “main” LED blinks when in Install mode. • Green “main” LED blinks when data reception by a destination device has been acknowledged.
PAGE 4
Wireless SNR Installation and Operation Manual Specifications Dimensions (W x H x D): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5” x 2 5/8” x 7/8” (127mm x 66.68mm x 22.23mm) Mounting Locations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wall Mount Temperature Range: . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
Installation Instructions 5 Installation Instructions The Wireless SNR installation process consists of the following basic steps: 1. Programming the Wireless SNR System ID. 2. Selecting appropriate locations and mounting the device(s). 3. Performing final ICMS configuration. Required Materials (Not Supplied) The following materials/tools are required for installation, but are not supplied: • General tool kit (screwdrivers, power drill, etc.
PAGE 6
Wireless SNR Installation and Operation Manual 3. Remove the batteries from the Wireless SNR, and then program the Wireless SNR System ID using one of the following three methods: • Program the System ID Wirelessly using a Transceiver or MSI Hub NOTE: Transceiver software must be version 13 or above. a. Ensure the Transceiver or MSI Hub has been poweredͲon and has already been programmed with the System ID. Observe the MSI Hub status LEDs (1).
PAGE 7
Installation Instructions 7 • Program the System ID using the HandͲHeld Wireless Programmer a. Set the desired System ID in the HandͲHeld Wireless Programmer. Refer to the HandͲHeld Wireless Programmer manual for instructions. b. After the System ID is set, press the [Mode] button to return to the main menu, select Config Devices, and then press [Enter / Żൣ]. c. Select System ID, and then press [Enter / Żൣ]. The System ID currently programmed into the Wireless Programmer is displayed. d.
PAGE 8
Wireless SNR Installation and Operation Manual Detailed Operation Control Theory The HeatͲTimer Wireless Network Sensor System is designed to be used in a variety of large buildings, garden apartments, and in retrofit applications. This gives both the accuracy and flexibility required to monitor those buildings' temperatures (giving the control more power to save fuel while keeping space temperatures at comfortable levels).
PAGE 9
Wireless System Information 9 Wireless System Information Installation Address: __________________________________________________________________ Wireless System ID: __________________________________________________________________ Locations: 1 Transceiver 2 Transceiver 3 Transceiver 4 Transceiver 5 Transceiver 6 Transceiver 7 Transceiver 8 Transceiver 9 Transceiver 10 Transceiver ID # ID # ID # ID # ID # ID # ID # ID # ID # ID # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2
PAGE 10
Wireless SNR Installation and Operation Manual Notes 059049-00 Rev. ' HeatͲTimer Corp.
PAGE 11
Notes 11 Notes HeatͲTimer Corp. 059049-00 Rev.
PAGE 12
WARRANTIES AND LIMITATIONS OF LIABILITY AND DAMAGE: Heat-Timer Corporation warrants that it will replace, or at its option, repair any Heat-Timer Corporation manufactured product or part thereof which is found to be defective in material workmanship within one year from the date of installation only if the warranty registration has been properly filled out and returned within 30 days of the date of installation.