Installation Guide

ManualsBrandsHeat-Fab ManualsHVAC3" Saf-T Vent Seal Modine HD Adapter

Technical Bulletin

www.heat-fab.com eng@heatfab.com

1 of 6 413.863.2242 800.772.0739 fax 413.863.4803

R1207 130 Industrial Boulevard Turners Falls MA 01376

Tips for a Successful Installation

Selkirk’s Saf-T Vent systems are Special Gas Vent systems designed to meet the unique venting challenges

presented by positive-pressure, condensing gas-fired appliances.

Saf-T Vent systems have been successfully installed in thousands of residential, commercial and industrial

settings with a track record of superior performance dating back nearly 20 years.

As part of our effort to continuously improve the products we manufacture, Selkirk has performed extensive

testing, visited job site installations and listened to countless installers. The information we have gathered has

prompted us to write this bulletin which highlights important installation practices that lead to gas-tight,

leak-proof, properly installed systems.

Key Points

1. Read & follow the appliance manufacturer’s instructions.

2. Read & follow Selkirk’s instructions.

3. When RTV Sealant is required, apply it correctly.

4. Secure the joint!

5. Get going in the right direction – Follow the flow arrows.

6. Maintain proper slope – Install with a continuous ¼” per foot (minimum)

slope back to the appliance.

7. Drain the condensate.

8. Provide adequate support – Support after every offset or elbow, after every 6 feet of horizontal run,

after every 30 feet of vertical run, and at each adjustable fitting.

9. Inspect annually.

1. Read & Follow the Appliance Manufacturer’s Instructions.

• Manufacturers develop and test their appliances to operate efficiently and safely when vented

properly. Many appliance installation manuals will give instructions on the maximum number of offsets

or elbows as well as the total equivalent length of vent allowed. Always refer to the manufacturer’s

manuals for guidance.

• Common venting of appliances is permitted only when allowed by the appliance manufacturer(s).

•

Some appliances must be vented with double-wall Saf-T Vent CI Plus. If the manual does not

distinguish between single-wall and double-wall, call us for a recommendation.

•

Manufacturer’s instructions supercede Heatfab manuals.

•

Clearance requirements outlined in the appliance manufacturer’s manuals must be followed. Their

clearances and/or national and local code requirements take priority over Heatfab instructions.

Summary of content (77 pages)

PAGE 1
Technical Bulletin Tips for a Successful Installation Selkirk’s Saf-T Vent systems are Special Gas Vent systems designed to meet the unique venting challenges presented by positive-pressure, condensing gas-fired appliances. Saf-T Vent systems have been successfully installed in thousands of residential, commercial and industrial settings with a track record of superior performance dating back nearly 20 years.
PAGE 2
Technical Bulletin 2. Read & Follow Selkirk’s Instructions. • • • • • Installation and Maintenance Instructions for Saf-T Vent systems are packaged with critical components (elbows, tees, and terminations), as are other supplemental instruction sheets for the critical component itself. Accessories (roof jacks, vertical supports, and wall penetrations) come with detailed instructions specific to their proper installation. If you have questions on correct installation methods, call us.
PAGE 3
Technical Bulletin • When assembling elbows and tees, the male end tabs will rotate around the vent to accommodate offsets and direction changes. Position the Mechanical Locking Strap over the Tabs, making sure each slot encompasses both Tabs, and then tighten. Center the Coupler Band around the completed joint and tighten. DO NOT use screws or pop rivets when joining Saf-T Vent systems! EXCEPTION: Saf-T Vent SC is designed to be assembled with the use of tap screws, which are included with each part. 5.
PAGE 4
Technical Bulletin 7. Drain the Condensate. • • • • • Follow the appliance manufacturer’s installation instructions. Some require condensate drains only for vent systems over a certain length. If a drain is required, Selkirk recommends: Drains at all transitions from horizontal to vertical vent runs. Immediately before a horizontal termination. After every 30 feet of continuous vent. The first drain should be as close to the appliance flue collar as possible.
PAGE 5
Technical Bulletin 9. Inspect Annually. • • • • During your annual HVAC equipment and system check, inspect the vent system. Make sure the system has not been damaged, the vent has not been punctured and the supports are solid. Look for the proper slope toward a drain. Make sure drains are not clogged or pinched off, and are in the proper place. Verify that all drain traps are properly primed. Inspect the termination and remove any accumulated debris.
PAGE 6
Technical Bulletin Connecting Saf-T Vent® EZ Seal to Appliances and Other Saf-T Vent Products EZ Seal IS Compatible with Existing Heat-fab Products. Here’s how: 1. Connecting to an Appliance Flue Collar • If the flue collar that comes with the appliance has Heat-fab’s integral red seal, you may attach EZ Seal pipe and fittings directly to it. Make the joint as described in the EZ Seal installation instructions (Pub # PI-EZ). Appliance flue collar has Heat-fab’s integral red seal. No sealant required.
PAGE 7
2. Connecting an EZ Seal Appliance Adapter to the Appliance • If the EZ Seal appliance adapter has been designed for a sealant-free connection to the appliance, it will have an integral red seal in the female end and in the end that attaches to the appliance. EZ Seal adapter with integral red seal on appliance end. No sealant required to attach to flue collar.
PAGE 8
3. Connecting EZ Seal to Saf-T Vent GC (single-wall) or Saf-T Vent CI (double-wall) • Saf-T Vent GC and Saf-T Vent CI lack the integral red seal. When you connect EZ Seal to them you will need to use an approved high-temperature RTV silicone sealant. Follow the procedure outlined in the GC or CI installation instructions (Pub # PI-VBH or PI-CIINS). EZ SEAL SAF-T VENT GC Sealant Required EZ SEAL SAF-T VENT CI 4.
PAGE 9
5. Connecting Saf-T Vent GC or Saf-T Vent CI to EZ Seal • Saf-T Vent GC and Saf-T Vent CI sections and fittings may be attached to an EZ Seal system: • If the male end (without tabs) of the GC or CI part was made with a butt-weld (a single layer of steel at the weld area), the part can be attached to an EZ Seal female end without using sealant.
PAGE 10
Technical and Dimensional Data Saf-T Vent ® Appliance Adapters AL 29-4C® Stainless Steel Special Gas Vent Heatfab Saf-T Vent Adapters are compatible with all Saf-T Vent Brands Appliance Listing by Make and Model starts on page 23 130 Industrial Boulevard Turners Falls, MA 01376 © Copyright 2008 Heatfab Division, Selkirk Corp. Saf-T Vent is a registered trademark of Selkirk Corp. AL29-4C is a registered trademark of ATI Properties, Inc. Pub.#11701-111208 Call (800) 772-0739 Fax (413) 863-4803 www.
PAGE 11
Saf-T Vent®Appliance Adapters ADAPTER 3" ADAPTERS PAGE 3 4" ADAPTERS 7 OVER THE COLLAR ADAPTERS 10 INTO THE FLUE COLLAR ADAPTERS 10 UNIVERSAL BOILER ADAPTERS 11 FLANGE TYPE ADAPTERS 12 AERCO ADAPTERS 13 BUDERUS ADAPTERS 15 DEDIETRICH 17 FULTON MUFFLER ADAPTERS 17 HYDROTHERM ADAPTERS 17 LAARS ADAPTERS 16 LOCHINVAR ADAPTERS 16 NORITZ ADAPTERS 18 P-K MACH ADAPTERS 18 RAYPAK ADAPTERS 20 RINNAI ADAPTERS 21 APPLIANCES, LISTED BY MAKE AND MODEL W/APPROPRIATE ADAPTER 23 Heatfab,
PAGE 12
Saf-T Vent®Appliance Adapters 3" Adapters —Adapters for appliances with 3" flue collars. 1/4" PIPE PLUG 3 4.25 6 Ø0.22 3" NPT 3 3.04 OD Ø4.88BC Ø5.38 9301AMTK 9301CRWN 9301FUL 3.5 3 3 3.10 OD 2.7 3.00 OD 9301ICP 9301THI 9301UTI 9301VSMN 6 4 1.63 3 Burnham (Gasketed) to Saf-T Vent EZ Saf-T Vent EZ to Burnham (Gasketed) 9353BUREZ Heatfab, Selkirk Corp 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 13
Saf-T Vent®Appliance Adapters 3.1 3" Adapters —Adapters for appliances with 3" flue collars. Ø .18 2 HOLES 180° APART 2.875 9301MOD 12 3.06 9302 MOD 10.5 3.25 5.31 3.68 3 12 5 3.16 ID 5.25 2 10.5 .38 2.37 ID (60mm) 9301PAL 9302PL 93PLSTEE Ø0.27 Ø3.53 BC 2.50 Ø4.00 9301VAIL Heatfab, Selkirk Corp 4 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 14
Saf-T Vent®Appliance Adapters 3" Adapters —Adapter for appliances with 3" flue collars. 5.88 4.5 4 3.9 2.85 3 2.79 9301BSH 1.62 9301CPVC 9314SMI 4.00 5.88 1.69 3.2 ID 3.50 OD 9301PVC 9301DEL 5.5 3.8 3.08 3.8 .5 9SF440696 9SF440697 Heatfab, Selkirk Corp 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 15
Saf-T Vent®Appliance Adapters 3" Weil-McLain Adapters —Adapters for Weil-McLain appliances. 7.0 4.25 CLAMP 6.25 4.5 CLAMP 93WMSTLH 93WMSTLV 8.8 7.17 5.31 3.68 4.64 3 CLAMP 3 3.52 6 5.25 2.64 3.75 .63 .38 93WMSTEE 93WMSTXL 2.55 2.88 4.00 CLAMP 93WMCGIS 93WMSTRT Heatfab, Selkirk Corp 6 CLAMP 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 16
Saf-T Vent®Appliance Adapters 4" Adapters —Adapters for appliances with 4" flue collars. 2.75 3 4.25 3.9 Ø0.22 3.8 4.04 OD Ø4.88 Ø5.38 9401AMTK 9401CPVC 9401CRWN 1/4" PIPE PLUG 6 6 4" NPT 1 4.04 ID 9401DUN 9401FUL 6 6 1.63 1.62 4 Burnham (Gasketed) to Saf-T Vent EZ Saf-T Vent EZ to Burnham (Gasketed) 9454BUREZ Heatfab, Selkirk Corp 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 17
Saf-T Vent®Appliance Adapters 4" Adapters —Adapters for appliances with 4" flue collars. 4.38 6 3 3.72 4.50 CLAMP 4.03 ID 9401ICP 9401MES 4.25 6 5.88 4.50 OD 4.01 9401MGTV 9401JVI 9401PVC 2 6 3 1 4.06 4.06 9401PVI 9401RHM Heatfab, Selkirk Corp 8 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 18
Saf-T Vent®Appliance Adapters 4" Adapters —Adapters for appliances with 4" flue collars. 6.25 5.55 4.5 6 3.85 4.15 OD 1.62 9414SMI 9401UTI 6 6 4.04OD 4.15 OD 9401SRI 9401VAIL 9401VSMN Heatfab, Selkirk Corp 130 Industrial Boulevard • Turners Falls, MA 01376 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 19
Saf-T Vent®Appliance Adapters Over-the-Flue-Collar Appliance Adapter — A generic flue collar adapter used on appliances with vent outlets that are slightly out-of-round or of irregular diameters. The split-seam design allows the adapter to clamp around irregular or inconsistent flue collars while still providing a secure connection to Saf-T Vent systems.
PAGE 20
Saf-T Vent®Appliance Adapters Universal Boiler Adapter— Used horizontally or vertically to adapt Saf-T Vent CI Plus to nominal diameter flue collars, it can also adapt to boiler collars that are slightly out of round. The adapter comes with a joint locking strap, boiler collar clamp and a 8" coupler band.
PAGE 21
Saf-T Vent®Appliance Adapters Flange-Type Appliance Adapter — A generic adapter used on appliances with a vent outlet that includes a bolted-on flange connection. Bolt holes and hardware are provided by the installer. Custom bolt hole patterns can be provided for an additional charge. Each Saf-T Vent CI Plus appliance adapter comes standard with a 8” long and a 5" long Saf-T Vent CI Coupler, the Saf-T Vent Ci appliance adapter comes standard with a 12" long Saf-T Vent CI Coupler.
PAGE 22
Saf-T Vent®Appliance Adapters Aerco Adapter —Adapters for Aerco appliances. Part Number Nominal Diameter 5604AER 5802AER CCA06ADKC CCA08ADBK 6 8 6 8 Installed Length Flange Diameter 18 12 18 12 9.19 11.63 9.19 11.63 Bolt Centers 7.75 10.13 7.75 10.13 Ø.5 TEST HOLE 2.5 2.5 Ø9.19 Ø0.31 18 Ø7.75BC 18 6"ID .8 CCA06ADKC .8 5604AER Ø11.63 Ø0.28 Ø10.
PAGE 23
Saf-T Vent®Appliance Adapters Aerco Elbow Adapter —90° elbow adapters for Aerco appliances. Note: To avoid water system supply and return piping, this fitting must be rotated from the vertical position. Part Number Nominal Diameter 5814AER CCA08ADBK90 Installed Length 8 8 12 12 Flange Diameter 11.63 11.63 Bolt Centers 10.13 10.13 12" Ø11.63" Ø10.13"BC 9" Ø0.28" Ø8"ID 1" CCA08ADBK90 12" 9" Ø11.62" Ø10.13"BC Ø8"ID Ø0.
PAGE 24
Saf-T Vent®Appliance Adapters Buderus Appliance Adapter — This adapter is specially designed to connect directly into the vent outlet of Buderus SB Series boilers. The hose clamp is tightened around the outside of the flue collar to create a mechanical joint. Part Number 9601SB* 9801SB 91001SB 91201SB 91401SB DIM - A Nominal Diameter 6 8 10 12 14 DIM - B Male End Crimp O.D. DIM - C Overall Length 7.18 7.9 9.9 11.9 13.9 7.5 4.0 4.0 4.0 4.0 DIM - D Crimp Length DIM - E Maximum Clamp Diameter 1.
PAGE 25
Saf-T Vent®Appliance Adapters Laars MightyMax Adapter — This adapter is specially designed to connect directly to the vent outlet of a Laars MightyMax Boiler. This part is supplied by Laars Heating Systems with MightyMax Boilers that require AL 29-4C® venting. Part Number 9601LARS 9701LARS 9801LARS 9901LARS 91001LARS DIM - A DIM - B DIM - C DIM - D Nominal Installed Plate Size Bolt Centers Diameter Length 6 7 8 9 10 4 4 4 4 4 7 8 9 10 11 6 7 8 9 10 C A D C B D Ø0.
PAGE 26
Saf-T Vent®Appliance Adapters Fulton Muffler Adapters —These adapters make the connection between Saf-T Vent products and Fulton Exhaust Mufflers. The 9401FMA is to connect to the 4" muffler and the 9601FMA is for the 6" muffler, both are made to connect to either single wall EZ Seal or double wall CI Plus. 9401FMA 9601FMA Hydrotherm Adapter — This adapter is specially designed to connect directly to the vent outlet of the Hydrotherm KN-10, the 9601K10 comes installed on the aapliance. . Ø0.40 3" Ø9.
PAGE 27
Saf-T Vent®Appliance Adapters Noritz Adapter —This adapter makes the connection between Saf-T Vent 5 products and Noritz water heaters that require 5" diameter vent. 4 6 4.79 9501NOR Patterson-Kelley Modu-Fire Adapter — These adapters are specially designed to connect directly to the vent outlet of Patterson Kelley Modu-Fire Boilers, MFD Series (Forced Draft). Consult Patterson-Kelley installation instructions on the use of reducing adapters.
PAGE 28
Saf-T Vent®Appliance Adapters P-K Mach Adapter — These adapters are specially designed to connect directly to the vent outlet of P-K Mach Boilers Note: Not all adapters are equipped with a test port. Part Number DIM - A Nominal Diameter 9401MACH 9501MACH 9601MACH 9801MACH 91001MACH 91002MACH 91001PK06 91002PK06 91001PK08 91002PK08 DIM - B Overall Diameter 4 5 6 8 10 10 6 6 8 8 3.93 5.14 DIM-C DIM-D Installed Length Length 11 7 9 5 FACTORY INSTALLED 7.9 9.8 10 9.8 10 9.
PAGE 29
Saf-T Vent®Appliance Adapters Raypak Boiler Adapter — This adapter is specially designed to connect directly into the vent outlet of Raypak’s ADB or High Delta boilers. The hose clamp is tightened around the outside of the flue collar to create a mechanical joint. Part Number DIM - A Nominal Diameter 9401RYPK 9501RYPK 9601RYPK 9801RYPK 9901RYPK 91001RYPK 91201RYPK 91401RYPK 91601RYPK 4 5 6 8 9 10 12 14 16 DIM - B Flue Collar I.D. 4 5 6 8 9 10 12 14 16 DIM - C Hose Clamp Diameter 4.5 5.5 6.5 8.5 9.
PAGE 30
Saf-T Vent®Appliance Adapters Rinnai Appliance Adapters — The straight adapter, SC03AD01, or elbow adapter, SC3AD01E, is specially designed to connect directly into the vent outlet of the Rinnai Continuum model V2532. 5"Ø OUTER 3"Ø INNER 3"Ø INNER 5"Ø OUTER 6 2 1/8" 7 SC03AD01 Straight Adapter SC03AD01E Elbow Adapter DeDietrich Adapter — SC Adapter for DTG FF 5 6 2 3 5.
PAGE 31
Saf-T Vent®Appliance Adapters Appliance Makes and Models: General Notes: The following appendix includes adapters from all of Heatfab’s Saf-T Vent brands. Adapters are listed by the appliance manufacturer. Heatfab Saf-T Vent adapters are compatible with all of Saf-T Vent brands pipes and fittings. EZ Seal to CI Plus and CI Plus to EZ Seal require an adapter, CCA_ADSV, refer to publication PI-CCADSV.
PAGE 32
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Aerco International KC1000 6 5604AER or CCA06ADKC 13 Ajax American A.O. Smith Water Products Bard Mfg. Benchmark BMK 1.5 6 Benchmark BMK 2.0 & BMK 3.0 8 5604AER or CCA06ADKC Benchmark BMK 2.
PAGE 33
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Beacon/Morris BRU, BRU30 - 90, BTU30 - 90 4 9401RHM 8 BRU / BTU 100-250 5 5501BOI OR CCA05ADUV 10 & 11 BRU / BTU 300-400 6 5601BOI OR CCA06ADUV 10 & 11 BST 30-75 4 9401RHM 8 ALL BM SERIES 4 thru 6 5_01BOI or CCA__ADUV 10 & 11 AquaStar 125FX 4 9464 10 AquaStar 240FX 4 9464 10 AquaStar 250SX 3 9301BSH 5 Pro Tankless GWH-635-ES 3 9301BSH 5 Bosch 2400E 3 9301BSH 5 GWH 2
PAGE 34
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Buderus GB312 90, 120, 160 VENTED WITH CPVC 6 96GBCPVC 15 GB312 200, 240, 280 VENTED WITH CPVC 8 98GBCPVC 15 GBS 3"/5" SC03AD07 (DESIGN TBD) GC124 / 3 & 4 5 5501BOI or CCA05ADUV 10 & 11 GC124 / 5 6 5601BOI or CCA06ADUV 10 & 11 Revolution Series 3 9353BUREZ 3 Series 2PV 3 9353BUREZ 3 Burnham Camus Spirit Series 3 9353BUREZ 3 INDEPENDENCE PV SERIES 3 9353BUREZ 3 MINUTEMAN
PAGE 35
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Camus Micoflame Grande MF2000 12 51201BOI or CCA12ADUV 10 & 11 Micoflame Grande MF2500, 3000 14 51401BOI or CCA14ADUV 10 & 11 Micoflame Grande MF3500, 4000 16 51601BOI or CCA16ADUV 10 & 11 UG045, 90, 180 3 9301UTI 3 Carel Cleaver Brooks Clearfire MCF-750 6 5601BOI or CCA06ADUV 10 & 11 Clearfire MCF-1000 8 5801BOI or CCA08ADUV 10 & 11 Clearfire MCF-1500 12 51201BOI or CCA12ADUV 1
PAGE 36
Saf-T Vent®Appliance Adapters Manufacturer DeDietrich Flue Collar Diameter Make & Model Adapter Part # Page GT 120 4 9401MGTV 8 DTG 120 FF 3"/5" SC03AD04 or SC03AD04T 21 GT 210A 6&7 5_01BOI or CCA__ADUV 10 & 11 GT300A 7&8 5_01BOI or CCA__ADUV 10 & 11 GT 400A 10 & 12 5_01BOI or CCA__ADUV 10 & 11 GTE 500A 16 & 18 5_01BOI or CCA__ADUV 10 & 11 XE Series (XE-2 thru XE-5) 4 9401DUN 7 XEB-2 thru XEB-5 3 9301THI 3 XEB-6 and XEB-7 4 9464 10 Ecosense (Rheem) ECO-180DV 3"/5"
PAGE 37
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Hatco Corporation Powermite PMG-100 & -200 4 5401BOI 10 Hayward Pool Prod. H250IDL, H350IDL, & H400IDL 6 Factory Supplied ( HF) H250FDN, H250FDP 6 Factory Supplied ( HF) H350FDN, H350FDP, H400FDN, H400FDP 8 Factory Supplied ( HF) PVG-2 thru PVG-5 4 9401DUN 7 PVGA-2 thru PVGA-5 3 9301THI 3 PVGA-6 and PVGA-7 4 9464 10 H. B.
PAGE 38
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Laars Heating Systems Rheos 2000 or Rheos Plus 2000 7 5701BOI or CCA07ADUV 10 & 11 Rheos 2400 or Rheos Plus 2400 10 51001BOI or CCA10ADUV 10 & 11 Pennant 500 (Cat I, III, & Sidewall) 6 5601BOI or CCA06ADUV 10 & 11 Pennant 750 (Cat. l) 8 5801BOI or CCA08ADUV 10 & 11 Pennant 750 (Cat. lI & Sidewall) 6 5601BOI or CCA06ADUV 10 & 11 Pennant 1000 (Cat.
PAGE 39
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Lochinvar Intelli-Fin IBL & IBN 1500 6 5601BOI or CCA06ADUV 10 & 11 Intelli-Fin IBL & IBN 1700 7 5701BOI or CCA07ADUV 10 & 11 Intelli-Fin IBL & IBN 2000 8 5801BOI or CCA08ADUV 10 & 11 Power-Fin PB & PF Series 0250 5 5501BOI or CCA05ADUV 10 & 11 7 5701BOI or CCA07ADUV 10 & 11 PB & PF Series 0750/0751 9 5901BOI or CCA09ADUV 10 & 11 PB & PF Series 1000/1001 10 51001BOI or CCA10ADUV 1
PAGE 40
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Monitor Products MZ Series 3"/5" SC03AD01 21 New Yorker PVCG Series (30 thru 60) 3 9353BUREZ 3 Nordyne Noritz Nortec Paloma Industries Patterson-Kelley FG6RA-045 3 9363 10 FG6RA-060 THRU -120 4 9464 10 FG6RA-144 5 9565 10 FG6RAK (all models) 4 9464 10 N-042 3 9301PAL 4 N-063S, N-069M, N-084M, N-084M-DV 4 9401RYPK 20 N-132 5 9501NOR 18 N-0531S 3 9301UTI 3 N-0631
PAGE 41
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Patterson-Kelley N1500MFD / N2000MFD WITH 6" VENTING 8 9801PK06 8" TO 6" REDUCER * 18 N1500MFD / N2000MFD WITH 6" UNIVERSAL VENTING 8 9801PK06UV 8" TO 6" REDUCER UNIV.
PAGE 42
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Pure Humidifier Co.
PAGE 43
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page RBI Water Heaters Futera II 500 (Cat. IV) 6 5601BOI or CCA06ADUV 10 & 11 RBI Water Heaters Reznor Rheem Futera II 500 (Cat. II) 8 5801BOI or CCA08ADUV 10 & 11 Futera II 750 (Cat. IV) 8 5801BOI or CCA08ADUV 10 & 11 Futera II 750 & 1000 (Cat. II) 10 51001BOI or CCA10ADUV 10 & 11 Futera II 1000 (Cat. IV) 9 5901BOI or CCA09ADUV 10 & 11 Futera II 1250, 1500 (Cat.
PAGE 44
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Richmond RMTG-42, RMTG-53 3 9301PAL 4 Rinnai Riverside Hydronics Ruud Slant/Fin Smith Boiler RMTG-74 4 9401RHM 8 RMTG-66DV 3"/5" SC03AD05 21 RMTG-53DV, RMTG-66DV 3"/5" SC03AD05 21 Continum 3 SC Vent Kit (HF), SC03AD01, SC03AD01E 21 R50LSI, R75LSI, R94LSI 3"/5" Standard SC components R98I, R98LSI 4 9401AMTK 7 Primera 400 6 5601BOI or CCA06ADUV 10 & 11 Primera 750, 1000 8
PAGE 45
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page State Water Heater Aurora Tankless 4 9401RYPK 20 GTS-305I, GTS-505I 3"/5" Standard SC components GTS-705I 4 9401AMTK 7 TF 100 - 250 5 9565 10 TF 300 - 400 6 9666 10 RF Series 4 9464 10 SIB140 Booster Heater 3 9363 10 SIB235 & SIB290 Booster Heater 4 9464 10 Sterling Stero Company Takagi FlashT-K1 4 9464 10 Flash T-K2 4 9464 10 Flash T-K3 4 9464 10 Flash T-H1 4
PAGE 46
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Thermo-Dynamics LMGD (all models) 4 9464 10 CWL-GS 120, 140, 160 Series 5 5501BOI or CCA05ADUV 10 & 11 LMD 75, 100, 110 5 5501BOI or CCA05ADUV 10 & 11 3 9301THI 3 3 9301DEL 5 Delta Performance (all models) 3 SC Vent Kit (Mfg.), EZ Vent Kit (Mfg.
PAGE 47
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Weben Jarco Vision 3000 750 6 Factory Supplied (HF) Vision 3000 1000 8 Factory Supplied (HF) Vision 3000 1500 & 2000 10 Factory Supplied (HF) E-Finiti E_020 3 5301BOI 10 E-Finiti E_040, E_060 4 5401BOI 10 E-Finiti E_075, E_100 6 5601BOI or CCA06ADUV 10 & 11 Weil-McLain E-Finiti E_125, E_150 8 5801BOI or CCA08ADUV 10 & 11 E-Finiti E_175, E_200 10 51001BOI or CCA10ADUV 10 & 11 Gold Se
PAGE 48
Technical and Dimensional Data Saf-T Vent ® Appliance Adapters AL 29-4C® Stainless Steel Special Gas Vent 130 Industrial Boulevard Turners Falls, MA 01376 © Copyright 2002 Heat-Fab, Incorporated Saf-T Vent is a registered trademark of Heat-Fab, Inc. AL29-4C is a registered trademark of ATI Properties, Inc. Pub.#11701-041106 Call (800) 772-0739 Fax (413) 863-4803 www.heat-fab.
PAGE 49
Saf-T Vent®Appliance Adapters Heat-fab Saf-T Vent adapters are compatible with all Saf-T Vent brands– EZ Seal, SC, CI, and CI Plus. A listing of Appliances by make and model with the appropriate Saf-T Vent adapter starts on page 20.
PAGE 50
Saf-T Vent®Appliance Adapters 3" Adapters —Adapters for appliances with 3" flue collars. 9301AMTK 9301ICP 9301CRWN 9301THI 9301FUL 9301UTI Burnham (Gasketed) to Saf-T Vent EZ 9301VSMN Saf-T Vent EZ to Burnham (Gasketed) 9353BUREZ 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.com Heat-fab, Inc.
PAGE 51
Saf-T Vent®Appliance Adapters 3" Adapters —Adapters for appliances with 3" flue collars. 9301MOD 9301PAL 9302 MOD 9302PL 93PLSTEE 9301VAIL Heat-fab, Inc. 4 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 52
Saf-T Vent®Appliance Adapters 3" Adapters —Adapter for appliances with 3" flue collars. 9301BSH 9301CPVC 9314SMI 9301DEL 9SF4406 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.com 9SF440697 Heat-fab, Inc.
PAGE 53
Saf-T Vent®Appliance Adapters 3" Weil-McLain Adapters —Adapters for Weil-McLain appliances. 93WMSTLH 93WMSTEE 93WMCGIS Heat-fab, Inc. 6 93WMSTLV 93WMSTXL 93WMSTRT 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 54
Saf-T Vent®Appliance Adapters 4" Adapters —Adapters for appliances with 4" flue collars. 9401AMTK 9401CPVC 9401CRWN 9401DUN 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.com 9401FUL Heat-fab, Inc.
PAGE 55
Saf-T Vent®Appliance Adapters 4" Adapters —Adapters for appliances with 4" flue collars. 9401ICP 9401MES 9401JVI 9401PVI Heat-fab, Inc. 8 9401RHM 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 56
Saf-T Vent®Appliance Adapters 4" Adapters —Adapters for appliances with 4" flue collars. 9414SMI 9401SRI 9401UTI 9401VAIL 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.com 9401VSMN Heat-fab, Inc.
PAGE 57
Saf-T Vent®Appliance Adapters Over-the-Flue-Collar Appliance Adapter — A generic flue collar adapter used on appliances with vent outlets that are slightly out-of-round or of irregular diameters. The split-seam design allows the adapter to clamp around irregular or inconsistent flue collars while still providing a secure connection to Saf-T Vent systems.
PAGE 58
Saf-T Vent®Appliance Adapters Universal Boiler Adapter— Used horizontally or vertically to adapt Saf-T Vent CI Plus to nominal diameter flue collars, it can also adapt to boiler collars that are slightly out of round. The adapter comes with a joint locking strap, boiler collar clamp and a 8" coupler band.
PAGE 59
Saf-T Vent®Appliance Adapters Flange-Type Appliance Adapter — A generic adapter used on appliances with a vent outlet that includes a bolted-on flange connection. Bolt holes and hardware are provided by the installer. Custom bolt hole patterns can be provided for an additional charge. Each Saf-T Vent CI Plus appliance adapter comes standard with a 8” long and a 5" long Saf-T Vent CI Coupler, the Saf-T Vent Ci appliance adapter comes standard with a 12" long Saf-T Vent CI Coupler.
PAGE 60
Saf-T Vent®Appliance Adapters Aerco Adapter —Adapters for Aerco appliances. Part Number 5604AER 5802AER CCA06ADKC CCA08ADBK Nominal Diameter 6 8 6 8 Installed Length Flange Diameter 18 12 18 12 9.19 11.63 9.19 11.63 Bolt Centers 7.75 10.13 7.75 10.13 6"ID CCA06ADKC 5604AER 8"ID CCA08ADBK 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.com 5802AER Heat-fab, Inc.
PAGE 61
Saf-T Vent®Appliance Adapters Aerco Elbow Adapter —90° elbow adapters for Aerco appliances. Note: To avoid water system supply and return piping, this fitting must be rotated from the vertical position. Part Number 5814AER CCA08ADBK90 Nominal Diameter 8 8 Installed Length 12 12 Flange Diameter 11.63 11.63 Bolt Centers 10.13 10.13 CCA08ADBK90 5814AER Heat-fab, Inc. 14 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.
PAGE 62
Saf-T Vent®Appliance Adapters Buderus Appliance Adapter — This adapter is specially designed to connect directly into the vent outlet of Buderus SB Series boilers. The hose clamp is tightened around the outside of the flue collar to create a mechanical joint. Part Number 9601SB* 9801SB 91001SB 91201SB 91401SB DIM - A Nominal Diameter 6 8 10 12 14 DIM - B Male End Crimp O.D. 7.18 7.9 9.9 11.9 13.9 DIM - C Overall Length 7.5 4.0 4.0 4.0 4.0 DIM - D Crimp Length DIM - E Maximum Clamp Diameter 1.
PAGE 63
Saf-T Vent®Appliance Adapters Laars MightyMax Adapter — This adapter is specially designed to connect directly to the vent outlet of a Laars MightyMax Boiler. This part is supplied by Laars Heating Systems with MightyMax Boilers that require AL 29-4C® venting.
PAGE 64
Saf-T Vent®Appliance Adapters Fulton Muffler Adapters —These adapters make the connection between Saf-T Vent products and Fulton Exhaust Mufflers. The 4" diameter has Saf-T Vent EZ Seal ends and the 6" diameter is made of heavy wall material and has non-gasketed Saf-T Vent ends. 9401FMA HS601FMA Noritz Adapter —This adapter makes the connection between Saf-T Vent products and Noritz water heaters that require 5" diameter vent.
PAGE 65
Saf-T Vent®Appliance Adapters Raypak Boiler Adapter — This adapter is specially designed to connect directly into the vent outlet of Raypak’s ADB or High Delta boilers. The hose clamp is tightened around the outside of the flue collar to create a mechanical joint. Part Number DIM - A Nominal Diameter 9401RYPK 9501RYPK 9601RYPK 9801RYPK 9901RYPK 91001RYPK 91201RYPK 91401RYPK 91601RYPK 4 5 6 8 9 10 12 14 16 DIM - B Flue Collar I.D. 4 5 6 8 9 10 12 14 16 DIM - C Hose Clamp Diameter 4.5 5.5 6.5 8.5 9.
PAGE 66
Saf-T Vent®Appliance Adapters Rinnai Appliance Adapters — The straight adapter, SC03AD01, or elbow adapter, SC3AD01E, is specially designed to connect directly into the vent outlet of the Rinnai Continuum model V2532. SC03AD01 Straight Adapter SC03AD01E Elbow Adapter 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.com Heat-fab, Inc.
PAGE 67
Saf-T Vent®Appliance Adapters Appliance Makes and Models: General Notes: The following appendix includes adapters from all of Heat-fab’s Saf-T Vent brands ; EZ Seal, SC, CI, and CI Plus. Adapters are listed by the appliance manufacturer. Heat-fab Saf-T Vent adapters are compatible with all of Saf-T Vent brands pipes and fittings. CI to EZ Seal, for more details please refer to Technical Bulletin # 11719. CI or EZ Seal to CI Plus requires an adapter, refer to publication PI-CCADKT.
PAGE 68
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Aerco International KC1000 Series (KC-1000 thru KC1000-8) 6 5604AER or CCA06ADKC 14 Benchmark (BMK 2.
PAGE 69
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Burnham Revolution Series Series 2PV Spirit Series Independence PV Series Minuteman Series XG2000A Series 3 3 3 3 3 3 9353BUREZ 9353BUREZ 9353BUREZ Burnham Vent ONLY Burnham Vent ONLY Burnham Vent ONLY 3 3 3 Camus Dynaflame 500 Dynaflame 750,1100 Dynaflame1500, 1750 Dynaflame 2000,2500, 3000 6 8 10 12 5601BOI or CCA06ADUV 5801BOI or CCA08ADUV 51001BOI or CCA10ADUV 51201BOI or CCA12ADUV 10 & 10 & 10
PAGE 70
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Gasmaster Industries GMI 200, 300, 400 4 5401BOI 10 GMI 600 GMI 800, 1M GMI 1.5M, 2M GMI 4M 6 8 12 18 5601BOI or CCA10ADUV 5801BOI or CCA8ADUV 51201BOI or CCA12ADUV 51801BOI or CC18ADUV 10 & 10 & 10 & 10 & Gibson see Nordyne Hatco Corporation Powermite PMG-100 & -200 4 5401BOI Hayward Pool Prod. H250IDL(P) & H400IDL(P) 6 Factory Supplied ( HF) H. B.
PAGE 71
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Laars Heating Systems Pennant 500 (Cat I, III, & Sidewall) 6 5601BOI or CCA06ADUV 10 & 11 8 6 10 8 12 10 14 12 5801BOI or CCA08ADUV 5601BOI or CCA06ADUV 51001BOI or CCA10ADUV 5801BOI or CCA08ADUV 51201BOI or CCA12ADUV 51001BOI or CCA10ADUV 51401BOI or CCA14ADUV 51201BOI or CCA12ADUV Pennant 750 (Cat. l) Pennant 750 (Cat. lI & Sidewall) Pennant 1000 (Cat. l) Pennant 1000 (Cat.
PAGE 72
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Modine Hot Dawg HD30 thru HD75 Hot Dawg Vent Cap Adapter 3 3 9301MOD 9302MOD 4 4 New Yorker PVCG Series (30 thru 60) 3 9353BUREZ 3 Nordyne FG6RA-045 FG6RA-060 THRU -120 FG6RA-144 FG6RAK (all models) 3 4 5 4 9363 9464 9565 9464 10 10 10 10 Noritz N-042 N-063S, N-069M, N-084M, N-084M-DV N-132 3 9301PAL 4 4 9401RYPK 18 5 9501NOR 17 Nortec GHB / GHP / GHMC 100 GHB / GHP / GHMC 200 and
PAGE 73
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Raypak B-50 & B-130A Gas Booster Heater 3 9363 10 B-195 Gas Booster Heater Advanced Design Boiler (ADB) ADB-500 ADB-750 ADB-1000 w/out CHX ADB-1000 with CHX ADB-1500 Hi Delta 122 162, 202, 242, 302 322, 402 and 502 652, 752, and 902 992 1262 and 1532 1802, 2002, and 2072 2342 4 9464 10 6 8 9 10 12 9601RYPK 9801RYPK 9901RYPK 91001RYPK 91201RYPK 18 18 18 18 18 4 5 6 8 10 12 14 16 9401RYPK 9501RYP
PAGE 74
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Reznor FT 30-65 BE & FE 25 -100 BE & FE 125 -250 BE & FE 300-400 4 4 5 6 9464 9464 9565 9666 10 10 10 10 Rheem Pronto! 4.2 / RTG-42 PH28 Pronto1 7.
PAGE 75
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Takagi Flash-T-K2 Flash-T-KD20* Mobius T-M1* T-K1S, T-K2, & T-K Jr.
PAGE 76
Saf-T Vent®Appliance Adapters Manufacturer Make & Model Flue Collar Diameter Adapter Part # Page Viessmann Vitogas 050 ECV (all models) Vitogas 100 GS10-72 Vitogas 100 GS10-84 Vitogas 100 GS10-96 Vitoden 200 WB2 6-24 & 8-32 Vitoden WB2 11-44 & 15 -60 Vertomat VSB-17, -22, -28 Vertomat VSB-37, -46, -57 Vertomat VSB-72, -89 3 8 9 10 3 4 8 10 12 9363 5801BOI or CCA08ADUV 5901BOI or CCA09ADUV 51001BOI or CCA10ADUV 9301VSMN 9401VSMN 5801BOI or CCA08ADUV 51001BOI or CCA10ADUV 51201BOI or CCA12ADUV 10 10
PAGE 77
Saf-T Vent®Appliance Adapters Notes: Heat-fab, Inc. 30 130 Industrial Boulevard • Turners Falls, MA 01376 Phone 800 772 0739 • Fax 413 863 4803 • www.heat-fab.