REMOTE CONTROLLER MANUAL DVC/DVH Series Inverter Single Zone Ductless Mini-Split Heat Controller • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.
DVC/DVH Remote Controller Heat Controller TABLE OF CONTENTS Batteries and Battery Specifications/Replacement........................................................ 3 Specifications and Features........................................................................................... 4 Functions........................................................................................................................ 5 Remote Control Display...................................................
Heat Controller DVC/DVH Remote Controller Remote Control Instructions 26 ft.(8 m) 1. The remote controller can be used to control and operate the unit 2. The remote’s signal can transmit up to 26 ft. (8 m) away. 3. Any obstructions between the signal of the remote control and the indoor unit can interfere, limiting the capacity of the signal. 4.
DVC/DVH Remote Controller Heat Controller Remote Controller Specifications Model Rated Voltage Signal Transmission Distance Operating Environment RG52A1/BGEFU1 3.0V 26ft (8m) with full batteries 23°F~ 140°F (-5~60°F) Performance Features 1. Operating Modes: AUTO, COOL, DRY, HEAT (heat pump models only) and FAN. 2. 24 hour timer 3. Temperature Range Selection: 62°F~ 86°F. 4. LCD (Liquid Crystal Display) NOTE: Remote controller can be set to display degrees in °C or °F.
Heat Controller DVC/DVH Remote Controller Functions 1 2 ON/OFF Press this button to power on, which starts the unit’s operation. Push the button again to power off, which stops the unit’s operation. MODE Each time this button is pressed, a mode is selected in a sequence of AUTO, COOL, DRY, HEAT*, and FAN then repeat. * *Heat mode is applicable to heat pump models only. 3 FAN Press to select the fan speed in four intervals: 4 SLEEP Press this button to activate the SLEEP mode.
DVC/DVH Remote Controller Heat Controller Functions 7 TEMP UP ( ) Push this button to increase the indoor temperature set point in 1°F increments up to 86°F. TEMP DOWN ( ) Push this button to decrease the indoor temperature set point in 1°F increments down to 62°F. 8 SHORTCUT • Used to restore the current settings or resume the previous setting. • The first time the unit is powered on and the SHORTCUT button is pressed, the unit will operate in AUTO mode, 80°F set temp, and auto fan speed.
Heat Controller DVC/DVH Remote Controller Functions 10 TIMER OFF Press the button to initiate the auto-off timer sequence. Each press will increase the auto-timer setting in 30 minutes increments. When the set time displays 10, each additional time the button is pressed it will increase the auto-timer setting in 60 minute increments. To cancel the auto-timer program, simply adjust the auto-off timer to 0.0.
DVC/DVH Remote Controller Heat Controller Remote Control Display MODE Displays the current operation mode. Including auto ( ), cool ( ), dry ( ), heat* ( ), fan ( ) and back to auto ( ). *Applicable to heat pump models only TRANSMISSION INDICATOR This transmission indicator lights when remote controller transmits signals to the indoor unit. ON/OFF Shows when unit is on. TIMER ON Displays when TIMER ON time is set. TIMER OFF Displays when TIMER OFF time is set.
Heat Controller DVC/DVH Remote Controller Remote Operation AUTO OPERATION 1. Press the MODE button to select Auto. 2. Press the UP/DOWN button to set the desired temperature. The temperature can be set within a range of 62°F~86°F in 1°F increments. • In Auto mode, the unit will automatically select Cool, Fan or Heat* modes be sensing the difference between the actual ambient room temperature and the set temperature on the remote controller. • In the Auto mode, you can not charge the fan speed.
DVC/DVH Remote Controller Heat Controller Remote Operation DRY OPERATION The DRY mode will automatically select the amount of dehumidification based on the difference between the set temperature and actual room temperature. The fan speed is automatically set to low. 1. Press the MODE button to select DRY mode. 2. Press the UP/DOWN buttons to set the desired temperature. The temperature can be set within a range of 62°F~86°F in 1°F increments. NOTE • In the Dry mode, you can not change the fan speed.
Heat Controller DVC/DVH Remote Controller Remote Operation TIMER OPERATION Press the TIMER ON button to set the time the unit should automatically turn on. Press the TIMER OFF button to set the time the unit should automatically turn off. 1. Press the TIMER ON button. The remote controller show TIMER ON, the last Auto-on set time and the “H” icon will be shown on the LCD display. Now it is ready to reset the Auto-on time to START operation. 2. Push the TIMER ON button again to set desired Autoon time.
DVC/DVH Remote Controller Heat Controller Remote Operation SLEEP FUNCTION The sleep function enables the unit to automatically change the temperature by 2°F per hour for the first two hours, then will remain steady for the next 5 hours, after that the unit will stop operating. SLEEP mode creates comfortable temperatures and saves energy. 1.
Heat Controller DVC/DVH Remote Controller 13
DVC/DVH Remote Controller Heat Controller 14
Heat Controller DVC/DVH Remote Controller 15
DVC/DVH Remote Controller Heat Controller 'XH WR RQJRLQJ SURGXFW LPSURYHPHQWV VSHFLILFDWLRQV DQG GLPHQVLRQV DUH VXEMHFW WR FKDQJH DQG FRUUHFWLRQ ZLWKRXW QRWLFH RU LQFXUULQJ REOLJDWLRQV 'HWHUPLQLQJ WKH DSSOLFDWLRQ DQG VXLWDELOLW\ IRU XVH RI DQ\ SURGXFW LV WKH UHVSRQVLELOLW\ RI WKH LQVWDOOHU $GGLWLRQDOO\ WKH LQVWDOOHU LV UHVSRQVLEOH IRU YHULI\LQJ GLPHQVLRQDO GDWD RQ WKH DFWXDO SURGXFW SULRU WR EHJLQQLQJ DQ\ LQVWDOODWLRQ SUHSDUDWLRQV ,QFHQWLYH DQG UHEDWH SURJUDPV KDYH SUHFLVH UHTXLUHPHQWV DV WR S
