6019 STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number: 1-800-577-9663 or email: customerservice@backyardproductsllc.
(This page intentionally left blank.
ASSEMBLY MANUAL 16019 04/10/2018 A Backyard Products Company VALUE SERIES BELMONT 8' x 8' (244 x 244 cm) ACTUAL FLOOR SIZE IS: 96 x 92-5/8" (243,8 x 235,2 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE IMPORTANT! READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY. BEFORE YOU BEGIN • BUILDING RESTRICTIONS AND APPROVALS Be sure to check with local building department and homeowners association for specific restrictions and/ or requirements before building.
TOOLS Required q Phillips Screwdriver Optional q Tool Belt/ Nail Pouch q Utility Knife q Shingle Blades q Drill / Driver q Tin Snips (for drip edge) q Caulk Gun q 5/16" Drill Bit q 1/8" Drill Bit q #2 Philips Drive Bit q Chalk Line q Paint Tools q Nail Gun • gun nails q Level q Safety Glasses q Pencil q Tape Measure q Square q Gloves q Ladder q Hammer or q Wood Glue Safety! Always use approved safety glasses during assembly.
CONCRETE FOUNDATION If you choose to install your kit on a concrete slab refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. B 3-1/2" (8,9 cm) C A R DOO 4" (10,2 cm) Building Size Actual Floor Size 8'x 8' (243,8 x 243,8 cm) 8'x 7'-8-5/8" (243,8 x 235,2 cm) A B C 96" (243,8 cm) 92-5/8" (235,3 cm) 85-5/8" (217,5 cm) Requires: x4 2 x 4 x 8' (5,1 x 10,2 x 243,8 cm) MUST be treated lumber.
ADDITIONAL MATERIALS FOR BUILDING YOUR SHED 3-TAB SHINGLES ............................ 4 Bundles 1" GALVANIZED ROOFING NAILS.... 2 Lbs For shingles. PAINT FOR TRIM .............................1 Quart PAINT FOR SIDING .......................... 2 Gallons Use 100% acrylic latex exterior paint. (2) coats recommended. Use 100% acrylic latex exterior paint. CAULK ................................................. 2 Tubes WOOD GLUE .......................
PA R TS IDENTIFICA TION AND SIZES WOOD SIZE CONVERSION CHART stamped on some parts. RS Nominal Board Size RS • Check these locations for part stamp. Actual Size 2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm ) 1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm ) 2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm ) 1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm ) PA R TS LIST INVENTORY YOUR PARTS before you begin.
WALL PANELS, AND DOORS x2 x4 3/8 x 48 x 72" (1 x 121,9 x 182,9 cm) x2 3/8 x 46-1/8 x 72" (1 x 117,2 x 182,9 cm) x1 x1 x1 x1 x1 3/8 x 20 x 72" (1 x 50,8 x 182,9 cm) LEFT DOOR x1 RIGHT DOOR ROOF PANELS x2 48" x 96" (121,9 x 243,8 cm) x2 7-7/8" x 96" (20 x 243,8 cm) Roof panels are 7/16" (1,1 cm) thick.
FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS 96" (243,8 cm) • 3" Screw angled into 4x4. • (2) at each point frame and 4x4 touch. 4x4 Runners (not included). 12" (30,5 cm) R DO O 12" (30,5 cm) Measurements to centers of 4x4's. MATERIAL REQUIRED x2 4" x 4" x 8' (10,2 x 10,2 x 243,8 cm) Treated Lumber Fasteners for Frame to 4"x 4".
FLOOR FRAME (NOT INCLUDED) PARTS REQUIRED: x5 x2 x28 3" (7,6 cm) TREATED 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) Floor framing materials not included. See page 4 for sizes and quantities. TREATED 2 x 4 x 92-5/8" (5,1 x 10,2 x 235,2 cm) 1 • FOR 10' x 12', SKIP TO PAGE 16 Orient parts as shown on flat surface. Measure and mark each dimension from end of boards 2 Use two 3" nails at each mark BEGIN FINISH 3 You have finished your floor frame. Proceed to level and square frame. 925 8" [235.
LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. BEGIN 1 See page 7 for the preferred floor leveling method. 2 Use level and check the frame is level before applying floor panels. 3 Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square.
FLOOR PANELS (NOT INCLUDED) PARTS REQUIRED: x53 x1 5/8 x 48 x 92-5/8" (1,6 x 122 x 235,2 cm) 2" (5,1 cm) Floor Panels not included See page 4 for panel sizes and quantities. Ensure your floor frame is square by installing one panel and squaring frame. BEGIN 1 Attach the 5/8 x 48 x 92-5/8" panel with the rough side up (painted-grid lines side) with the 48" edge and corner flush to the floor frame (Fig A). Secure panel with two 2" nails in the corners. 2 Move to the opposite end.
FLOOR PANELS (NOT INCLUDED) PARTS REQUIRED: x53 x1 2" (5,1 cm) 5/8 x 48 x 92-5/8" (1,6 x 122 x 235,2 cm) 5 Continue by installing 5/8 x 48 x 92-5/8" panel with rough side up (painted grid lines). Use a chalk line or grid lines on panels for 2" nails 6" apart on edges and 12" apart inside panel. FINISH 6 You have finished Installing your floor panels. DOOR Flush 6" (15,2 cm) edges of panel. 48" (121,9 cm) 12" (30,5 cm) inside panel.
I M PIMPORTANT! O R TA N T ! Check the floor frame is level after installing floor panels. Re-level if needed. OR DO • The floor should be used as a stable work surface for wall construction. HINT: • Organize your assembly procedure during the build process to avoid over-handling of the walls.
SIDE WALL FRAMES PARTS REQUIRED: x10 x4 x40 3" (7,6 cm) FZ 2 x 3 x 66-1/2 " (5,1 x 7,6 x 168,9 cm) PNA 2 x 3 x 92-1/2" (5,1 x 7,6 x 235 cm) BEGIN 1 Orient parts on edge on floor. Measure and mark from end of boards. IMPORTANT! You will build two walls the same. 2 FINISH 3 Use two 3" nails at each mark. You have finished building one side wall frame. Proceed to attach wall panels.
SIDE WALL PANELS PARTS REQUIRED: x90 x2 DQ GAA 3/8 x 46-1/8 x 72" (1 x 117,2 x 182,8 cm) 2" (5,1 cm) 2x3" 3/4" GAUGE BLOCK GAUGE BLOCK Ensure your wall frame is square by installing one panel and squaring frame. BEGIN 1 Place a 46-1/8 x 72" panel onto wall frame with primed side up as shown. Locate the panel 1-1/2" above the top plate. Use a DQ as a gauge block for the 1-1/2" top overhang measurement. Use the GAA gauge block to mark the 3/4" side measurement on the wall stud.
SIDE WALL PANELS PARTS REQUIRED: x2 x90 2" (5,1 cm) DQ 3/8 x 46-1/8 x 72" (1 x 117,2 x 182,8 cm) 2x3" GAUGE BLOCK 4 Place 46-1/8" panel on frame as shown with primed side facing up flush with first panel. Nail using 2" nails 6" apart on edges and 12" apart inside panel. 5 Carefully flip your sidewall over. Repeat STEPS 1-4 to assemble your second side wall. FINISH 6 You have finished building both of your side walls. To draw panels tight at seams angle nail.
BACK WALL FRAME PARTS REQUIRED: x1 x1 x2 3" (7,6 cm) CI 2 x 3 x 34" (5,1 x 7,6 x 86,4 cm) PS 2 x 3 x 91 " (5,1 x 7,6 x 231,1 cm) BEGIN 1 Center PS flush on CI on edge on floor as shown (Fig. A). 2 Nail using two 3" nails at each connection. 91" (231,1 cm) 45-1/2" (115,6 cm) PS 45-1/2" (115,6 cm) Fig.
BACK WALL FRAME PARTS REQUIRED: x2 x1 x2 CI 2 x 3 x 34" (5,1 x 7,6 x 86,4 cm) x1 3" (7,6 cm) 3" (7,6 cm) PT 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm) 4 Center CI flush on PS on flat using a gusset as a temporary spacer. 5 Center PT on CI on edge on floor as shown. 6 Nail PT to CI using two 3" Nails (Fig. A). 7 Use two 3" screws at middle connection (Fig. B). FINISH You have finished building your back wall frame.
BACK WALL PANELS PARTS REQUIRED: x22 x1 2" (5,1 cm) 3/8 x 48 x 72" (1 x 121,9 x 182,9 cm) BEGIN 1 Place LEFT panel on back frame as shown with primed side facing up. 2 Secure Using 2" nails 6" apart on edges and 12" apart inside panel. Ensure 34" spacing before nailing panel. For squareness maintain flush and 3/4" measurement along panel edges.
BACK WALL PANELS PARTS REQUIRED: x11 2" (5,1 cm) x11 x1 1-1/2" (3,8 cm) 3/8 x 48 x 72" (1 x 121,9 x 182,9 cm) 3 Place RIGHT panel on back frame as shown with primed side facing up and flush to panel. Ensure 34" (86,4 cm) between PT and PS. 4 Secure Using 2" nails 6" apart on edges and 12" apart inside panel. FINISH 5 You have finished installing your back wall panels. Flush Ensure 34" spacing before nailing panel.
FRONT WALL FRAME PARTS REQUIRED: x2 x2 3/8 x 20 x 72" (1 x 50,8 x 182,9 cm) x1 x8 BV 2" (5,1 cm) 2 x 3 x 17-1/2" (5,1 x 7,6 x 44,5 cm) TEMPORARY SUPPORT PT 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm) BEGIN 1 2 Orient PT on edge and place LEFT panel on PT as shown with primed side facing up. Use BV as a temporary support as shown. Nail using 2" nails 4" apart. 3 Repeat steps 1-2 for RIGHT panel.
FRONT WALL PANELS PARTS REQUIRED: x2 x6 BV 2" (5,1 cm) 2 x 3 x 17-1/2" (5,1 x 7,6 x 44,5 cm) BEGIN 1 Position BV on edge, 2-1/2" from outside edge and 1" from bottom edge of LEFT wall panel. (Fig A.) 2 Nail BV to wall panel using (3) 2" Nails. 3 Repeat step 1-2 for RIGHT wall panel. (Fig B.) FINISH 4 You have finished building your front wall.
FRONT WALL TOP PLATE PARTS REQUIRED: x1 x5 FZ 3" (7,6 cm) x1 GUSSET 2 x 3 x 66-1/2" (5,1 x 7,6 x 168,9 cm) TEMPORARY SPACER BEGIN 1 Center FZ on PT on flat, flush to front wall panel (Fig. A). 2 Secure using five 3" screws on angle spaced evenly. 3 Mark center of door opening for later alignment. FZ Flush Flush FZ Front wall panel Fig. A 5-1/4" Use to maintain 3/8" overhang.
SIDE WALL INSTALLATION PARTS REQUIRED (TEMPORARY): x1 x2 OO 3" (7,6 cm) x8 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) TEMPORARY SUPPORT 3" (7,6 cm) x17 2" (5,1 cm) BEGIN 1 Center side wall assembly on the 92-1/2" (235 cm) floor dimension. Ensure 1-1/2" measurement is on top 2 Use OO as a temporary brace. Secure with two 3" screws. 1-1/2" overhang 92-1/2 3" (7,6 cm) Screws cm) OO D O O R " (235 3 First, nail lower edge of panel to floor frame using 2" nails 6" apart.
SIDE WALL INSTALLATION PARTS REQUIRED: x26 x19 x10 SIDE 1-1/2"WALL (3,8 cm) INSTALLATION 3" (7,6 cm) 2" (5,1 cm) PARTS REQUIRED: x26 x10 1-1/2" (3,8 cm) x19 2" (5,1 cm) BEGIN 3" (7,6 cm) It is important to secure the side wall in the following order: 1 Set back wall on side wall top plates and secure using two 3" It is important to secure the screws on each side (Fig.A).
FRONT WALL INSTALLATION PARTS REQUIRED: x8 x4 2" (5,1 cm) x26 3" (7,6 cm) x6 3" (7,6 cm) 1-1/2" (3,8 cm) It is important to secure the front wall in the following order: BEGIN 1 Center front wall assembly on floor, resting top plate on side walls. 2 Secure front wall top plate to side walls using two 3" screws (Fig. A, B). 3 4 Secure lower edge of panel to floor frame using eight 2" nails 6" apart. Angle nail to hit floor frame (Fig. C).
RAFTERS PARTS REQUIRED: x6 6 x 24" (15,2 x 61 cm) x6 WI x72 x1 2 x 4 x 54-1/16" (5,1 x 10,2 x 129,8 cm) 2" (5,1 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) TEMPORARY SUPPORT BEGIN You will build THREE assemblies; Place two rafter-halves WI in the corner of back and side walls. Rafters contact at peak. 1 HINT: 96” (243,8 cm) Use floor and walls to help assemble rafters! Fit base of rafters in corners of back wall.
RAFTERS x12 PARTS REQUIRED: x6 x3 3" (7,6 cm) 2" (5,1 cm) PRE-ASSEMBLED BEGIN 1 Locate rafters directly over the wall studs. Ensure you have the measurements shown. 2 Screw through panel into end of rafter with 2" screw (Fig. A). 3 Secure with two 3" screws angled at each end (Fig. B). FINISH 4 You have finished installing your rafters. NOTE: Measurements from outside of panels 22-5/8" (57,5 cm) 24" (61 cm) 24" (61 cm) Align over studs. Maintain the measurements between rafters. Fig.
BACK WALL GABLE PANELS PARTS REQUIRED: x1 LW x10 2 x 3 x 23-7/8" (5,1 x 7,6 x 60,6 cm) x1 x1 BEGIN 1 Place LW on flat on floor. 2 Place RIGHT gable panel primed side up, centered on LW with a 3/4" overhang on bottom. Nail using five 1-1/2" nails, 6" apart. 3 Place LEFT gable panel primed side up, flush to right panel on LW with a 3/4" overhang on bottom. Nail using five 1-1/2" Nails, 6" apart. FINISH 4 You have finished building your back wall gable panels.
BACK WALL GABLE PANELS PARTS REQUIRED: x2 x18 3" (7,6 cm) 2" (5,1 cm) PRE-ASSEMBLED BEGIN 1 Place gable assembly centered on back wall top plate overlapping the back wall panels 3/4" (Fig. A). 2 Nail assembly to back wall panels using 2" nails 6" apart. 3 Screw LW to top plate using two 3" screws (Fig. B). FINISH 4 You have finished installing your back wall gable panels. (2) 3" (7,6 cm) Screws Fig.
FRONT WALL GABLE PANELS PARTS REQUIRED: x2 DQ x8 2 x 3 x 11-7/8" (5,1 x 7,6 x 30,2 cm) x1 x1 BEGIN 1 Place DQ on flat on floor as shown. 2 Place RIGHT gable panel primed side up, centered on top DQ as shown. Secure using two 1-1/2" nails. 3 Orient LEFT gable panel primed side up, flush to right panel on DQ's with a 1-1/2" overhang on bottom. Nail using four 1-1/2" Nails. FINISH 4 You have finished building your Front wall gable panels.
WINDOW INSTALL x2 PARTS REQUIRED: 1" (2,5 cm) x1 1/8" (0,3 cm)Drill Bit BEGIN 1 2 Center window in window opening as shown.Make shown. Makesure sureframe both is at an measurements are equal from equal distance from bottom of bottom. panel (Fig. A). Secure window to DQ using one screw in top and bottom (Fig. B). EQUAL Fig. A (2) 1" (2,5 cm) Screws Fig.
WINDOW INSTALLINSTALL WINDOW ARTS REQUIRED: PARTS REQUIRED: WQ x2 WO x2 EGIN x8x8 1 x 2 x 11" (2,5 x15,1 cm) x 5,1 x 27,9 cm) x 2xx27,9 11" (2,5 WQ NOTE POINT 1 WO x 2 x 14" (2,5 x15,1 cm) x 5,1 x 35,6 cm) x 2 xx 35,6 14" (2,5 BEGIN BEGIN 1 window trim window. 11 Center Place window framing on �framing at asonshown. window facewindow down on framing. Place window on �atPlace as shown. Place face down on framing. 2 22 WO Place one under window asusing shown. Secure using two 1/2" screws.
FRONT WALL GABLE PANELS PARTS REQUIRED: x2 WINDOW INSTALL PARTS REQUIRED: 3" (7,6 cm) x18 x1 2" (5,1 cm) 1/8" (0,3 cm)Drill Bit PRE-ASSEMBLED 1 Center window in window opening as shown. Make sure both BEGIN measurements are equal from bottom. 2 BEGIN 1 Place gable assembly centered on front wall top plate overlapping front wall panels. 2 Screw DQ to top plate using two 3" screws (Fig. A). 3 Nail gable panels to front wall panels and LW using 2" nails, 6" apart.
GABLE TRIM x40 PARTS REQUIRED: x4 WX 1-1/4" (3,2 cm) 2 x 3 x 55-3/4" (5,1 x 7,6 x 141,6 cm) ¸1 BEGIN Install front gable trim WX flush to top edge of panel and flush at peak (Fig. A) as shown. 2 Attach trim to wall using 1-1/4" screws 7-1/4" apart. Screw through panels into WX. 3 Repeat above steps 1-2 to secure back wall gable trim. FINISH 4 You have finished installing your gable trim. IF YOU DO NOT HAVE THE DELUXE PACKAGE CONTINUE TO PAGE 43.
ROOF PANELS PARTS REQUIRED: x8 7/16 x 48 x 96" (1,1 x 121,9 x 243,8 cm) x2 2" (5,1 cm) Roof panels may cause serious injury until securely fastened. You must square the roof by attaching one panel first. You will use the panels’ long edge as a lever to bring your roof into square. Commonly known as “racking”. BEGIN 1 Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with a 1/2" measurement on the gable trim (Fig A) and the panel flush at the peak (Fig. B). Flush at peak.
ROOF PANELS PARTS REQUIRED: x2 x86 2" (5,1 cm) 7/16 x 7-7/8" x 96" (1,1 x 20 x 243,8 cm) Keep spacing between the center of the rafters at the lower edge of the panel and secure with one 2" nail into each rafter (Fig. E). 3 NOTE: Measurements from outside of gable trim. Move to the top of the panel and keep spacing between the center of the rafters. Secure with one 2" nail into each rafter (Fig. E).
TRIM x56 PARTS REQUIRED: 2" (5,1 cm) x4 3/8 x 1-3/4 x 71-1/4" (1 x 4,4 x 181 cm) x4 3/8 x 1-3/4 x 71-3/4" (1 x 4,4 x 182,2 cm) ¸1 BEGIN Attach 71-3/4" trim �ush to back of gable trim and bottom of roof panel and trim (Fig. A) using 2" (5,1 cm) �nish nail as shown. 2 Attach 71-1/4" trim �ush to bottom of gable panel (Fig. B ) and �ush to edge of 71-3/4" trim using one 2" (5,1 cm) nail as shown. 3 Finish attaching trim �ush to corners using seven 2" (5,1 cm) �nish nails as shown.
DOORS PARTS REQUIRED: x4 x1 3" (7,6 cm) OO x2 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) TEMPORARY SUPPORT 1-1/4" (3,2 cm) HINT: Look for 3/8" SPACER attached to doors. x1 x1 Left Door x1 GAA Right Door 1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) BEGIN 1 Orient parts as shown on flat surface. (right) and green (left) on hinge board. 2 Attach temporary support OO with 3" screws in middle and at ends as shown. Tighten securely. 3 Attach temporary support GAA with two 1-1/4" screws as shown.
DOORS x7 PARTS REQUIRED: x1 4 3" (7,6 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) TEMPORARY SUPPORT Attach temporary support OO as a ledger board flush under wall panels for doors to rest on, using three 3" screws (Fig. A). 72" (182,9 cm ) from bottom of gable panel to top of ledger boar d 72" from gable panel s OO OO Fig. A 5 Center doors on panel seam as shown (Fig. B). Check ledger board is still flush under panels.
DOOR PARTS REQUIRED: x1 x1 x52 WR 19/32 x 3 x 63" (1,5 x 7,6 x 160 cm) 3/4" (1,9 cm) x8 2" (5 cm) x10 3/4" (1,9 cm) 56" (142,2 cm) Metal Threshold Bagged separately / special coating BEGIN 1 Secure hinge boards from inside using 3/4" screws as shown (Fig. A). 2 Reinforce the door trim using 3/4" screws through door panel into trim (Fig. A). Locate screws as shown in Fig. B. Use two screws at seams. 3 Center trim WR over doors and secure using eight 2" finish nails into framing as shown.
DOOR WEATHERSTRIP PARTS REQUIRED: x2 x14 OO 2" (5 cm) 1-1/4 x 2-1/2 x 69" (3,2 x 7,6 x 175,3 cm) BEGIN 1 With left door closed, center a weatherstrip OO vertically on the left door in the door opening (Fig. A). OO will offset the left door 1" OUT past the door trim 1" (Fig. B). 2 Secure OO using seven 2" screws through outside trim into OO (Fig. B) 3 On right door center OO vertically in door opening (Fig. A). OO will offset the right door 1" IN from the door trim (Fig. C).
DOOR PARTS REQUIRED: x4 x1 1" (2,5 cm) x7 x1 5/16" (0,8 cm) Drill Bit 3/4" (1,9 cm) BEGIN 1 2 3 Place bolt onto OO in open position with bolt end 1/4" down from frame. Bolt is open when loop is contacting base (Fig A). Mark and pre-drill holes for screws. Install bolt with screws supplied and drill 5/16" hole for bolt to extend into door frame. Install hasp on right door and latch on left door. Bottom edge of hasp is 35-1/2" (90 cm) up from bottom edge of door trim.
PAINT & CAULK - NOT INCLUDED - • Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. • Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: • Bottom edge of all siding and trim • Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting. (Follow directions provided by manufacturer.
SHINGLES - NOT INCLUDED • Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch SHINGLE NAIL PATTERN 1" (2,5cm) 1/2" (1,3cm) Notch Sealing Str ip 1" (2,5cm) Half A Rain Slot Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. BEGIN 1 Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.
SHINGLES continued... 2 2 Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge. Roof Deck FRONT OF SHED 1" (2,5 cm) Notch - or - BACK OF SHED Flush with starter row. Drip Edge Flush with starter row. Notch 3 Install second row of shingles flush at top of first row's rain slots. Ensure 1" overhang or flush to drip edge at front, stagger each row. FRONT OF SHED BACK OF SHED 1" (2,5 cm) Notch Flush with rain slots.
SHINGLES continued... 5 Continue installing rows of shingles to the peak. At the peak make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at ridge cut to peak with a utility knife. Cut Off. 5" (12,7 cm) MAX. CUT Top of rain slot. • If more than 5" to rain slot you must install another row of shingles. 6 Repeat steps 1 - 5 to shingle the opposite side of your roof. Trim shingles at ridge. 7 Once both sides are shingled you need to trim ends.
SHINGLES - RIDGE CAP • You will finish off the top of the roof with a ridge cap made from shingles. BEGIN 1 Cut shingles into THREE pieces. Hint: Use cut-off pieces first. 2" (5,1 cm) 2" (5,1 cm) 2" (5,1 cm) 2" (5,1 cm) 2" (5,1 cm) 2" (5,1 cm) Score shingle, then snap-off angled cut. Weather Seal Top of slot. Note: • You will need about 20 - 22 cut pieces. 2 20 to 22 Pieces Install first ridge cap flush to shingles at front, as shown. (1) Nail per side through weather seal.
SHINGLES - RIDGE CAP continued... 4 Continue installing ridge cap to back of roof. 5 Make sure there is 4" between the shingle-color and edge of shingles. Trim cap off flush to shingles 6 When you have 4" minimum of shingle color cut one piece to cap your roof. Cap 7 Install flush to shingles. Flush to shingles (2) Nails per side. FINISH 8 You have finished your ridge cap.
WARRANTY REGISTRATION Please complete your warranty registration to properly validate your warranty. Register your product online at:www.OnlineWarranty.net. LIMITED CONDITIONAL WARRANTY* Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for 1 year. 2. All accessories, hardware and metal components are warranted for 2 years. 3. All Oriented Strand Board (OSB) is warranted for 2 years 4.
