Instructions / Assembly

ManualsBrandsHearthSense ManualsFireplaces42 in. Corner Ventless Liquid Propane Gas Tower Fireplace in Cherry

NOTE: Carefully inspect each part for shipping damage before beginning assembly. Compare the carton contents with the

list above. All necessary hardware is provided to fasten the mantel parts together. When tightening screws, do not over

tighten. This may cause threads to strip. For this reason, we recommend using a manual screwdriver rather than a power

screwdriver. Do not force screws into holes.

1. Put 6 Cam Dowels (K) onto Underside Panel (D), and connect

Left & Right Panel (H) with Underside Panel (D). Then put 6

Cam Locks (L) onto Left & Right Panel (H) and fix these Cam

Locks (L) with a manual screwdriver. (Figure 1)

PART DESCRIPTION QTY

PARTS

A TOP 1

B UPSIDE PANEL 1

C MIDDLE CLAPBOARD 1

D UNDERSIDE PANEL 1

E BASE 1

F DRAWER ASSEMBLY 1

G CLAPBOARD 2

H LEFT& RIGHT PANEL 2

I BACK PANEL 1

J CONNECT PANEL 2

HARDWARE

K CAM DOWEL 38

L CAM LOCK 38

M WOOD DOWEL 14

N SCREW 1 4

O SCREW 2 8

P PIN 8

Q SCREW 3 10

Carton contents

Tower Corner Mantel and

Base Assembly Instructions

MODEL: ATC

Figure 1

Summary of content (4 pages)

PAGE 1
Tower Corner Mantel and Base Assembly Instructions Carton contents PART DESCRIPTION MODEL: ATC A QTY PARTS A TOP 1 B UPSIDE PANEL 1 C MIDDLE CLAPBOARD 1 D UNDERSIDE PANEL 1 E BASE 1 F DRAWER ASSEMBLY 1 G CLAPBOARD 2 H LEFT& RIGHT PANEL 2 I BACK PANEL 1 J CONNECT PANEL 2 M N HARDWARE K CAM DOWEL 38 L CAM LOCK 38 M WOOD DOWEL 14 N SCREW 1 4 O SCREW 2 8 P PIN 8 Q SCREW 3 10 B J K L O F I C H H G D P G E Q NOTE: Carefully inspect each part for s
PAGE 2
. Put 8 Cam Dowels (K) and 4 Wood Dowels (M) onto Base (E), D and place Underside Panel (D) and Left & Right Panel (H) assembly onto Base (E). Then put 8 Cam Locks (L) onto H Left & Right Panel (H) and Underside Panel (D), and fix H them with a manual screwdriver. (Figure 2) 3. Put 8 Pins (P) onto Underside Panel (D) and Left & Right L M Panel (H) assembly, and lay 2 Clapboards (G) onto these K Pins (P), leave proper space between two Clapboards (G).
PAGE 3
F 6．Put 4 Cam Dowels (K) onto Middle Clapboard (C), and lay Drawer Assembly (F) on Middle Clapboard (C), then put 4 Cam Locks(L) on Drawer Assembly (F) and fix them with a manual screwdriver. (Figure 6) C L 7．Put 5 Cam Dowels (K) and 2 Wood Dowels (M) onto K Top (A), and lay Top (A) to Upside Panel (B). Then put 5 Cam Locks (L) onto Upside Panel (B) and fix them with G a manual screwdriver.
PAGE 4
FIREPLACE INSTALLATION 1. Fireplace should be fully assembled. Refer to fireplace owner’s manual. 2. Place mantel assembly close to installation location. Refer to fireplace owner’s manual for installation clearances. Provide enough room to insert fireplace from back of mantel. 3. Install gas line per the requirements outlined in the fireplace owner’s manual. Remember to leave access to the gas shutoff valve where it is accessible to the user. 4.