User's Manual

ManualsBrandsHearth & Home Technologies ManualsElectronicsRemote Control Transmitter

Hearth & Home Technologies • RC200 Multifunction Remote Control • 2166-392 • 6/09

Installation & Operating Instructions

RC200

IntelliFire Plus™ Multifunction Remote Control

Hearth & Home Technologies disclaims any responsibility for,

and the warranty will be voided by, the following actions:

• Installation and use of any damaged system component.

• Modicationofthesystemcomponent.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not approved

by Hearth & Home Technologies.

Any such action may cause a re hazard.

• Read, understand and follow these instructions for safe

installation and operation.

Introduction

The RC200 multifunctional wireless wall control with

docking station is designed to control constant pilot fea-

ture, ame height, blower speed and to turn your gas

replaceonandoff.TheRC200remotecontrolisonly

for use with the Hearth & Home Technologies IntelliFire

Plus™ system (IPI).

Installation Precautions

This control is tested and safe when installed in accor-

dance with this installation manual. Do not install any

components that may be damaged.

Do not modify, disassemble, or substitute any of the com-

ponents included with this kit. Installation of this unit must

bedonebyaqualiedservicetechnician.

Placement of this remote control may affect performance.

An assessment of the space should be done prior to in-

stallation for optimum performance.

Determine Location

Determine the location for the remote control. The selected

locationshouldbeinthesamespaceasthegasreplace

withvisualsightofreplace.Theremotecontrolmustbe

placedwithin30feetofthereplace.

The RC200 is approved for interior installation and should

always be placed under weather resistant cover when used

in exterior applications.

Installation of Remote Control Housing

CAUTION! Risk of Fire! DO NOT install damaged or

modied components. Warranty will be voided if damaged

or modied components are installed.

Kit components: One remote control, two #6 screws, two

wall anchors, one A23 battery and one AUX200 module (if

purchased retail).

1. Remove remote control components from packaging.

2. Remove battery cover from the back of the remote by

sliding it down and install A23 battery.

3.Securetheremotecontrolhousingonaatwallsur-

face using the two screws and wall anchors provided.

See Figure 1.

Figure 1. Mounting Remote Control Housing

4. Place remote control inside housing. See Figure 2.

Figure 2. Remote in Housing

Summary of content (4 pages)

PAGE 1
RC200 IntelliFire Plus™ Multifunction Remote Control Installation & Operating Instructions Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions: • Installation and use of any damaged system component. • Modification of the system component. • Installation other than as instructed by Hearth & Home Technologies. • Installation and/or use of any component part not approved by Hearth & Home Technologies. Any such action may cause a fire hazard.
PAGE 2
5. Close the housing door and press the power button. The red light illuminates if the batteries were properly installed. See Figure 3. Programming the RC200 to the Control Module CAUTION! Risk of burns! DO NOT program the remote control to the control module when fireplace is hot. • Verify the ON/OFF/REMOTE switch is in the REMOTE position. Control module will beep twice when ready. See Figure 6.
PAGE 3
Function Buttons V Menu Select Menu V Select V • Remove battery cover from the back of the remote by sliding it down. Slide the child lock switch to enable or disable the child lock feature. See Figure 7. V the FLAME button to adjust the flame Press height. The flame height can be adjusted to 5 different settings: MAX, HIGH, MEDIUM, LOW, MIN. Flame height will not be adjustable for first ten seconds when fireplace is turned on.
PAGE 4
Power Outage • If fireplace battery backup system IS installed at time of power outage, fireplace operation will not be interrupted. • If fireplace battery backup system IS NOT installed at time of power outage, fireplace will shut off. To resume fireplace operation, install battery backup. WARNING! Risk of burns! In the event of a wall switch malfunction, DO NOT attempt to turn off the fireplace manually using the control module. The decorative front will be hot and severe burns may occur.