Owner’s Manual Installation and Operation Models: BE-36-C BE-36-CIPI CAUTION DO NOT DISCARD THIS MANUAL • Important operating and maintenance instructions included. • Read, understand and follow these instructions for safe installation and operation. WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or death.
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Hearth & Home Technologies gas appliance —an elegant and clean alternative to wood burning appliances. The Hearth & Home Technologies gas appliance you have selected is designed to provide the utmost in safety, reliability, and efficiency. This Owner’s Manual should be retained for future reference.
- Table of Contents - Section 2: Section 3: Section 4: Î Section 5: Getting Started A. Design and Installation Considerations ......... 6 B. Tools and Supplies Needed ........................... 6 C. Inspect Appliance and Components .............. 6 Framing and Clearances A. Selecting Appliance Location......................... 7 B. Constructing the Appliance Chase ................ 8 C. Clearances .................................................... 8 D. Mantel Projections .............................
1 Listing and Code Approvals A. Appliance Certification MODELS: BE-36-C, BE-36-CIPI LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.88-2002 • CSA2.33-M02 • UL307B This product is listed to ANSI standards for “Vented Gas Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”. NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
NOTE: The following requirements reference various Massachusetts and national codes not contained in this document. G.
2 Getting Started A. Design and Installation Considerations C. Inspect Appliance and Components Hearth & Home Technologies direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. WARNING Inspect appliance and components for damage. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components.
3 Framing and Clearances NOTE: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONLY. • Illustrations/diagrams are not drawn to scale. • Actual installation may vary due to individual design preference. WARNING Fire Risk Provide adequate clearance: • Around air openings • To combustibles • For service access Locate appliance away from traffic areas. A.
B. Constructing the Appliance Chase Gas line holes and other openings should be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room. A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase. C.
D. Mantel Projections Note: Clearance from opening to perpendicular wall. 1” 2” Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) Figure 3.3 Clearances to Mantels or other Combustibles above Appliance Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev.
4 Termination Locations A. Vent Termination Minimum Clearances HORIZONTAL OVERHANG WARNING Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as specified. 2 FT. MIN. 20 INCHES MIN. VERTICAL WALL LOWEST DISCHARGE OPENING GAS DIRECT VENT TERMINATION CAP • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fire. X 12 ROOF PITCH IS X/ 12 H (MIN.
M N P R Q (See Note 2) V T V S Electrical Service S V D* V V = VENT TERMINAL A B D* = 12 inches ...............clearances above grade, veranda, (See Note 1) porch, deck or balcony = 12 inches ...............clearances to window or door that may be opened, or to permanently closed window. (Glass) = 18 inches ...............vertical clearance to unventilated soffit or to ventilated soffit located above the terminal *30 inches ..............
5 Vent Information and Diagrams A. Vent Table Key The abbreviations listed in this vent table key are used in the vent diagrams. First section (closest to appliance) of vertical length V2 Second section of vertical length H1 First section (closest to appliance) of horizontal length H2 Second section of horizontal length Vertical in . V1 8-1/2 in. WARNING Fire Hazard. Explosion Risk. Asphyxiation Risk.
D. Use of Flex Vent The flex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than ½ inch sag between supports. A support is required at each change in venting direction, and in any location where it is necessary to maintain the necessary clearance to combustibles. A simple “up and out” installation (Figure 5.3) requires only enough support to maintain the necessary clearance to combustibles.
E. Vent Diagrams WARNING Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling firestops. • ALWAYS maintain specified clearances around venting and firestop systems. • Install wall shield and ceiling firestops as specified. Failure to keep insulation or other material away from vent pipe may cause fire. 1. Top Vent - Horizontal Termination One Elbow V Minimum 90 Elbow Only Note: Use SL D- Series components only. V1 BE-36-C NG BE-36-C LP 1-1/2 ft. 457 mm 1-1/2 ft.
1. Top Vent - Horizontal Termination - (continued) Three Elbows H1 Maximum V Minimum H1 + H2 Maximum BE-36-C NG & LP 90 Elbow Only 1-1/2 ft. 457 mm BE-36-C NG 2 ft. BE-36-C LP 610 mm 2 ft. 610 mm 1/2 ft. 152 mm 1-1/2 ft. 457 mm 4 ft. 1.2 m 3 ft. 914 mm 1-1/2 ft. 457 mm 3 ft. 914 mm 6 ft. 1.8 m 6 ft. 1.8 m 2-1/2 ft. 762 mm 5 ft. 1.5 m 10 ft. 3.0 m 10 ft. 3.0 m 3-1/2 ft. 1.1 m 7 ft. 2.1 m 14 ft. 4.3 m 14 ft. 4.3 m 4-1/2 ft. 1.4 m 15 ft. 4.6 m 14 ft. 4.
Top Vent - Vertical Termination No Elbows V1 = 44 ft. Max. (13.4 m) NOTE: For vertical venting over 20 feet an extended vertical baffle is recommended for improved flame appearance. Note: Use SL D- Series components only. Baffles are recommended for these vertically terminated products which have excessive draft. Baffles compensate for high draft, restore visual flame height, and limit excessive cooling resulting from too much secondary air.
2. Top Vent - Vertical Termination - (continued) Two Elbows V Minimum 90 Elbow Only V2 BE-36-C LP 1-1/2 ft. 457 mm 1-1/2 ft. 457 mm 152 mm 2 ft. 610 mm 1-1/2 ft. 457 mm 1-1/2 ft. 457 mm 3 ft. 914 mm 3 ft. 914 mm 2-1/2 ft. 762 mm 5 ft. 1.5 m 5 ft. 1.5 m 3-1/2 ft. 1.1 m 7 ft. 2.1 m 7 ft. 2.1 m 4-1/2 ft. 1.4 m 15 ft. 4.6 m 15 ft. 4.6 m 1/2 ft. H1 H1 Maximum BE-36-C NG V1 H1 MAX. =15 FT (4.6 m) V1 + V2 + H1 MAX. = 40 FT (12.
3. Rear Vent - Horizontal Termination No Elbows H1 = 28 in. (711 mm) Maximum Note: Use DVP Series components only. Figure 5.11 Rear Vent - Horizontal Termination One 45º Elbow H1 = 9 in. (229 mm) Maximum Note: Use DVP Series components only. Figure 5.12 18 Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev.
3. Rear Vent - Horizontal Termination- (continued) Two elbows V Minimum Note: Use DVP Series components only. H1 Maximum H1 + H2 Maximum 0 ft. 0 mm 1-1/2 ft. 457 mm 2-1/2 ft. 762 mm 1 ft. 305 mm 3-1/2 ft. 1.1 m 6-1/2 ft. 2m 2 ft. 762 mm 5-1/2 ft. 1.7 m 10-1/2 ft. 3.2 m 3 ft. 1.1 m 7-1/2 ft. 2.3 m 14 ft. 4.3 m H1 + H2 MAX. =14 FT (4.3 m) V1 + H1 + H2 MAX. = 40 FT (12.2 m) Figure 5.13 3. Rear Vent - Horizontal TerminationThree elbows Note: Use DVP Series components only.
3. Rear Vent - Horizontal Termination- (continued) One elbow V Minimum Note: Use DVP Series components only. H1 Maximum 1 ft. 305 mm 3-1/2 ft. 1.1 m 2 ft. 762 mm 5-1/2 ft. 1.7 m 3 ft. 1.1 m 7-1/2 ft. 2.3 m H1 MAX. =7-1/2 FT (2.3 m) V1 + H1 MAX. = 40 FT (12.2 m) V1 H1 Figure 5.15 V Minimum 3. Rear Vent - Horizontal Termination Two elbows Note: Use DVP Series components only. 1 ft. 305 mm 2-1/2 ft. 762 mm 2 ft. 762 mm 4-1/2 ft. 1.4 m 3 ft. 1.1 m 6-1/2 ft. 2m H1 + H2 MAX.
3. Rear Vent - Horizontal Termination- (continued) Three elbows V Minimum Note: Use DVP Series components only. H1 Maximum H1 + H2 + H3 Maximum 0 ft. 0 mm 1-1/2 ft. 457 mm 2-1/2 ft. 762 mm 1 ft. 305 mm 3-1/2 ft. 1.1 m 6-1/2 ft. 2m 2 ft. 762 mm 5-1/2 ft. 1.7 m 10-1/2 ft. 3.2 m 3 ft. 1.1 m 7-1/2 ft. 2.3 m 14 ft. 4.3 m H1 MAX. =7-1/2 FT (2.3 m) H1 + H2 MAX. =14 FT (4.3 m) V1 + V2 + H1 + H2 MAX. = 40 FT (12.2 m) V2 H2 V1 H1 Figure 5.
6 Vent Clearances and Framing B. Wall Penetration Framing A. Pipe Clearances to Combustibles WARNING Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as specified. • Do not pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause fire. C NOTE: Slope not required. D 3 in. TOP CLEARANCE A* 1 in. CLEARANCE AROUND VERTICAL SECTIONS B* 1 in. SIDE AND BOTTOM CLEARANCE BE-36-C Figure 6.
C. Vertical Penetration Framing WARNING Fire Hazard Keep loose materials or blown insulation from touching the vent pipe. • National building codes recommend using attic shield to keep loose materials/ blown insulation from contacting vent. ATTIC ABOVE • Hearth & Home Technologies requires the use of an attic shield. 10 IN. (254 MM) Installing the Ceiling Firestop • Frame an opening 10 inches by 10 inches whenever the vent system penetrates a ceiling/floor (see Figure 6.4).
7 Appliance Preparation A. Choosing the Top or Rear Vent Note: Actual unit may look different than the fireplace shown in this section. CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. Figure 7.4 Remove the seal cap. Figure 7.1 For top vent, remove the two screws holding the elbow heat shield in place. Use this heat shield over the first elbow if applicable. For rear vent skip this step. Figure 7.
Figure 7.7 To attach the first section of vent pipe, make sure to use the fiberglass gasket in the manual bag to seal between the first vent component and the outer fireplace wrap. Use 2 self tapping screws to secure the gasket to the outer wrap. Figure 7.10 Fold the center parts of the retaining band out and use to remove the vent cap. Secure the first section of venting to the fireplace by screwing through the two tabs bent up out of the vent hole in the heat shield.
C. Securing and Leveling the Appliance WARNING Fire Risk. • Prevent contact with sagging, loose insulation. • Do NOT install against combustible materials such as exposed insulation, plastic and insulation backer. The diagram shows how to properly position, level, and secure the appliance (see Figure 7.11). Nailing tabs are provided to secure the appliance to the framing members. • Rear venting - refer to Vent Clearances and Framing (Section 6B) for hole location. • Place the appliance into position.
8 Installing Vent Pipe A. Assembly of Vent Sections (DVP Pipe ONLY) WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches. • Use pilot holes for screws. • Screws must not exceed one inch long. • Pipe may separate if not properly joined. Figure 8.
Assembling Minimum Installations (MI) Sections MI sections are non-unitized so that they can be cut to a certain length. Cut these sections to length from the nonexpanded end (see Figure 8.5). Cut from this end (outer) They can then be attached by first connecting the expanded end of the MI inner flue with the inner pipe from the adjacent pipe section and securing with three screws. The expanded portion of the MI inner flue must overlap completely with the unexpanded end of the adjacent pipe section.
Securing the Vent Sections Vertical Sections Vertical sections of pipe must be supported every 8 feet after the 25 foot maximum unsupported rise. The vent support or plumber’s strap (spaced 120° apart) may be used to do this (see Figure 8.8). Horizontal Sections Horizontal sections of vent must be supported every 5 feet with a vent support or plumber’s strap. Figure 8.8 Securing Vertical Pipe Sections Figure 8.9 Securing Horizontal Pipe Sections B.
Assembly of Vent Sections (SL Series Pipe ONLY) WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Ensure vent components are locked together correctly. • Pipe may separate if not properly joined.
C. Installing Heat Shield and Horizontal Termination Cap (DVP Pipe ONLY) WARNING Fire Hazard Impaired performance of appliance • Telescoping flue section of termination cap MUST be used when connecting pipe section to termination cap. • Maintain a 1-1/2 inch minimum overlap on telescoping flue section of termination cap. WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches. • Use pilot holes for screws.
Installing Wall Shield Firestops and Horizontal Termination Cap (SL Series Pipe ONLY) WARNING WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Ensure vent components are locked together correctly. • Pipe may separate if not properly joined. For Horizontal Runs - Wall shield firestops are REQUIRED on both sides of a combustible wall through which the vent passes. NOTE: Model SLK-01TRD does not need an exterior wall shield firestop on an exterior combustible wall.
Caulk the gap between the roof flashing and the outside diameter of the pipe. Also caulk the perimeter of flashing that contacts roof surface as shown in Figure 8.18. To install roof flashing see Figure 8.16. For installation of vertical termination cap see minimum vent heights for various pitched roofs (see Figure 8.16) . HORIZONTAL OVERHANG 2 FT. MIN. 20 INCHES MIN. VERTICAL WALL Î D.
Assembling and Installing Storm Collar CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. Connect both halves of the storm collar with two screws (see Figure 8.19). Wrap the storm collar around the exposed pipe section and align brackets. Insert a bolt (provided) through the brackets and tighten nut to complete storm collar assembly (see Figure 8.20). Slide the assembled storm collar down the pipe section until it rests on the roof flashing. Figure 8.
9 Gas Information A. Fuel Conversions C. Gas Connection Before making gas connections ensure that appliance being installed is compatible with the available gas type. Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specified and approved parts. NOTE: Have the gas supply line installed in accordance with local building codes, if any. If not, follow ANSI 223.1.
• Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. HIGH ALTITUDE INSTALLATIONS • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. U.L. Listed gas appliances are tested and approved without requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada. WARNING Fire or Explosion Hazard • Gas buildup during line purge may ignite.
10 Electrical Information A. Recommendation for Wire B. Connecting to the Appliance This appliance requires 110-120 VAC be wired to the junction box either for use of optional accessories (standing pilot ignition) or for proper operation of the appliance (Intellifire ignition). Refer to Figure 10.1 to determine if the appliance uses an Intellifire ignition system or Standing Pilot ignition system. Open the control access panel to view wiring system and gas valve.
C. Standing Pilot Ignition System Wiring D. Intellifire Ignition System Wiring • This standing pilot ignition system wiring does not require a 110 VAC supply to operate. This appliance requires a 110 VAC supply to the appliance junction box for operation. A wiring diagram is shown in Figure 10.3. • It is recommended that a 110 VAC junction box be installed for use with a fan or remote control. (See Figure 10.4 for junction box wiring).
E. Junction Box Installation Romex Connector If the box is being wired from the appliance: Remove the screw attaching the junction box to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 10.4). • Pull the electrical wires from outside the appliance through this opening into the valve compartment. • Loosen the two screws on the Romex connector (not included with unit), feed the necessary length of wire through the connector and tighten the screws.
11 Finishing A. Mantel Projections FINISH WALL MATERIAL MAY BE COMBUSTIBLE - TOP AND SIDES Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. 0 IN. 1-1/4 IN. 0 IN. 0 IN. HIGH TEMPERATURE (3000F / 1490 C MIN.) TOP & SIDE SEAL JOINT 1” 2” Figure 11.3 Noncombustible Facing WARNING Figure 11.
12 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the firebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity. C. Accessories WARNING Explosion Risk. • Follow ember placement instructions in manual. • Do NOT place embers directly over burner ports. • Replace ember material annually. Improperly placed embers interferes with proper burner operation.
D. Positioning the Logs Log Set Assembly: LOGS-BE-36-C If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions. Models: BE-36-C 1 TAB TAB 2 3 Carefully remove the logs from the packaging. CAUTION: Logs are fragile! 1 2 LOG #1 (SRV397-701): Place log #1 so the notch on the right side rests on the right grate tine. The left side of log #1 should rest on the pilot bracket.
E. Glass Assembly F. Grilles and Trim WARNING Handle glass doors with care. • Inspect the gasket to ensure it is undamaged. • Inspect the glass for cracks, chips or scratches. • Any scratch in glass, requires replacement. • Do NOT strike, slam or scratch glass. • Do NOT operate appliance with glass door removed, cracked, broken or scratched. • Replace glass door assembly as a complete appliance. Install optional marble and brass trim surround kits as desired.
13 Operating Instructions A. Before Lighting Appliance Before lighting this appliance determine if it has a Standing Pilot or Intellifire ignition system by opening the control access panel to view wiring system and gas valve. If this appliance has a red or black ignitor button (see Figure 10.1) this appliance has a Standing Pilot ignition system. If there is no red or black ignitor button, this appliance has an Intellifire ignition system.
B. Lighting Appliance FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS (IPI) WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. 1. Turn off all electric power to the appliance. A. This appliance is equipped with an intermittent pilot ignition (IPI) device which automatically lights the burner. Do not try to light the burner by hand. • Immediately call your gas supplier from a neighbor’s phone.
Standing Pilot Ignition FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS 1. Turn off all electric power to the appliance. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING, smell all around the appliance area for gas.
C. After Appliance is Lit Initial Break-in Procedure When you light the appliance, you may notice that it produces heat which does have an associated odor or smell. If you feel this odor is excessive it may require the initial three to four hour continuous burn on high followed by a second burn up to 12 hours to fully drive off any odor from paint and lubricants used in the manufacturing process. Condensation of the glass is normal.
14 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. A. Standing Pilot Ignition System Symptom Possible Causes Corrective Action 1. After repeated triggering a.
Troubleshooting (continued) Symptom 3. Continued Possible Cause Corrective Action c. Defective valve. Turn the valve knob to the ON position. Place the ON/OFF switch in the ON position. Check the millivolt meter a the thermopile terminals. The millivolt meter should read greater than 125mV. If the reading is acceptable, and if the burner does not come on, replace the gas valve. d. Plugged burner orifice. Check the burner orifice for stoppage. Remove stoppage. e. Wall switch or wires are defective.
B. Intellifire Ignition System Sympton 1. The ignitor/module makes noise, but no spark. 2. Pilot won’t light, there is no noise or spark. Possible Cause Corrective Action a. Incorrect wiring. Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected to correct terminals on module and pilot assembly. Reversed wires at the module may cause system to make sparking noise, but spark may not be present at pilot hood. b. Loose connections or electrical shorts in the wiring.
Intellifire Ignition System - (continued) Symptom 3. (Continued) Pilot lights but continues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot flame has been lit, flame rectification has not occurred.) 4. Pilot sparks, but Pilot will not light. Possible Cause Corrective Action c. Module is not grounded. Verify that module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to module. d.
15 Maintaining and Servicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance check-up at the beginning of each heating season. WARNING CAUTION Risk of injury or property damage. Before servicing: • Turn off gas. • Turn off electricity to appliance. • Disable remote control, if one is present. • Ensure appliance is completely cooled.
Inspect Doors, Surrounds and Fronts Maintenance Tasks 1. Assess condition of screen and replace as necessary. Recommend addition of screen if one is not present. 2. Inspect for scratches, dents or other damage and repair as necessary. 3. Verify no obstructions to airflow through the louvers. 4. Verify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Assembly and Glass 1. Inspect gasket seal and its condition. 2.
16 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
B. Vent Components Diagrams Pipe Effective Height/Length DVP Pipe (see chart) Effective Length Inches Millimeters DVP4 4 102 DVP6 6 152 DVP12 12 305 DVP24 24 610 DVP36 36 914 DVP48 48 1219 DVP6A 3 to 6 76 to 152 DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 10-1/2 in. (267 mm) 45° 4-7/8 in. ( 276 mm) 10-7/8 in. (276 mm) DVP45 (45 ° Elbow) 11-3/8 in. (289 mm) 10 in. (254 mm) 10 in. (254 mm) 1 in. (25 mm) 7-3/8 in. (187 mm) 24 in.
B. Vent Components Diagrams (continued) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B will be required. 8 in. (203 mm) Heat Shield 15-1/8 in. (384 mm) Term Cap 12 in.
B. Vent Components Diagrams (continued) 31 in. (787 mm) 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF6M Roof Flashing Multi-pak RF12M Roof Flashing Multi-pak 5 in. (127 mm) 13-3/4 in. (349 mm) 11-7/8 in. (302 mm) 5 in. (127 mm) 13-7/8 in. (352 mm) 13-3/4 in. (349 mm) DVP-BEK2 DVP-HPC Cap Brick Extension BEK Trap Cap Brick Extension 11-5/8 in. (295 mm) 12-1/8 in. (308 mm) 7-1/8 in. (181 mm) 5-3/4 in.
B. Vent Components Diagrams (continued) 7-3/8 in. (187 mm) 1-1/2 in. (38 mm) 3-7/8 in. (98 mm) 17-3/4 in. (451 mm) 14 in. (356 mm) 10-1/2 in. (267 mm) DVP-TV Vertical Termination Cap 12 in. (305 mm) DVP-TB1 Basement Vent Ca p 7-1/4 in. (184 mm) 12-1/2 in. (318 mm) 5-1/4 in. (133 mm) PVK-80 (For use with IPI and DSI appliances only.) 14 in. (356 mm) 16-7/8 in. (429 mm) 12 in. (305 mm) 7-1/8 in. (181 mm) 12-1/8 in. (314 mm) DVP-TVHW Vertical Termination Cap (High wind) 8-3/4 in. (222 mm) 1 in.
B. Vent Components Diagrams (continued) 6-1/2 in. Pipe Length/Inches SL-06D SL-09D SL-12D SL-12/17D SL-17/24D SL-24D SL-36D SL-48D SL-FLEX-2 SL-FLEX-3 SL-FLEX-5 SL-FLEX-10 5-3/4 8-3/4 11-3/4 11-3/4 to 16-3/4 16-3/4 to 23-3/4 23-3/4 35-3/4 47-3/4 24 36 60 120 There must be a 25% reduction in total H when using the snorkel cap except when using the simple up and out installation. WALL BRACKET (SL- SERIES) Figure 16.
C. Service Parts BE-36-C Service Parts Diagram Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ Î 9 5 6 7 4 11 12 10 Log Set Assembly 8 1 2 Part number list on following page. 60 Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev.
Î C. BE-36-C Service Parts List IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Service Parts Î BE-36-C Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ Valve Assembly List Standing Pilot Valve Assembly 3 4 6 5 8 7 1 2 IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Service Parts Î BE-36-CIPI Beginning Manufacturing Date: 4-01 Ending Manufacturing Date: ______ Valve Assembly Parts List IPI Valve Assembly 4 3 6 5 14 12 9 7 11 2 13 10 IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
D. Limited Lifetime Warranty LIMITED LIFETIME WARRANTY Hearth & Home Technologies BASIC ONE-YEAR WARRANTY. HEARTH & HOME TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville, MN 55044, warrants to the original owner that your new HEARTH & HOME TECHNOLOGIES Gas Appliance (the “Product”) will be free from defects in materials and workmanship for a period of one year from the date of installation.
E. Contact Information Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.fireside.com Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the location of your nearest Hearth & Home Technologies dealer, please visit www.fireside.com.
