Instructions / Assembly

0706
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.
Connect the tool to the air resource.
Push down on the latch button(B). Pull back on
the inner magazine (C).
Please load the fasteners with the head of the
staples facing the same direction as the work
contact element beneath the magazine.
Push the inner magazine(C) forward until latch
button pops up.
This
tool is a bottom loading stapler!
OPERATION
⒈
⒉
⒊
LOADING FASTENERS
FEATURES
Latch button(B)
●
●
●
●
360° ADJUSTABLE EXHAUST
COMFORT-GRIP HANDLE
ERGONOMICALLY ENGINEERED BODY
Allows user to direct air away from face.
For increased comfort and control.
Rugged and Comfortable debris free, extending
tool life.
NON-MARRING SAFETY CONTACT
Eliminates damage to working surface.
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
WARNING:
!
UNPACKING
This tool has been shipped completely
assembled.
Make sure that all items listed in the packing
list are included.
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
breakage or damage occurred during
shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
If any parts are damaged or missing, please
call .1-866-676-8468
●
●
●
●
●
●
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
WARNING:
!
Compatible with All Generic Fine Wire Staples.
FEATURES
SPECIFICATIONS
REQUIRES:
AIR INLET:
MAGAZINE CAPACITY:
WEIGHT:
MAXIMUM PRESSURE:
PRESSURE RANGE:
3.8 SCFM with 100
fasteners per minute @ 90 psi
1/4 inch NPT
100 fasteners
1.7 lbs
100 psi
60 psi 100 psi–
PIN SIZE RANGE: 1/4 inch to 9/16 inch
Inner Magazine (C)
LOADING TOOL
Do not load the tool with fasteners when
any one of the operating controls is
activated.
Never place a hand or any part of body in
fastener discharge area of tool.
Never point tool at anyone.
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
●
●
●
●
The tool may fire when it is first
connected to the air resource. Always
connect the tool to the air resource
before loading fasteners to prevent injury
from unintended cycling. Always make
sure the tool's magazine is empty at the
beginning of each work session, before
connecting to an air resource.
WARNING:
!
Keep the tool pointed away from yourself
and others when loading fasteners.
Failure to do so could result in possible
serious personal injury.
WARNING:
!
Never load fasteners with the workpiece
contact or trigger activated. Doing so
could result in possible serious personal
injury.
WARNING:
!
UNLOADING FASTENERS
Unloading is the reverse of loading. Always
disconnect the air resource before unloading.
Always unload all fasteners before removing
tool from service.
WARNING:
!
Always disconnect the air resource before
unloading.
WARNING:
!
CLEARING JAMS
Disconnect the tool from air resource.
Remove fasteners from the tool. Failure to do
so will cause the fasteners to eject from the front
of the tool.
Completely remove the small nose screws (E)
and the top nose plate (F) to reveal the jammed
fastener.
Using caution not to bend or damage the driver
blade, using pliers or a screwdriver if required to
clear the jammed fastener.
Put the nose plate (F) back on the nose (G),
fastening it with the screws (E).
Reconnect the tool to the air resource.
Reload the tool with fasteners.
Occasionally, a fastener may become jammed in
the firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:
⒊
⒋
⒌
⒍
⒎
1.
2.
Use only those fasteners recommended
for use with this tool. Fasteners not
identified for use with this tool by the tool
manufacturer are able to result in a risk of
injury to persons or tool damage when
used in this tool.
WARNING:
!
Before unloading or making adjustments.
When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
When tool is not in use.
When moving to a different work area.
Such precautionary measures reduce the risk of
injury to persons.
⒋