Use and Care Manual

Safety Information(Continued)
AIR SUPPLY AND CONNECTIONS
TheConnectoronthe tool must not hold pressure when
air supply is disconnected. If an incorrect fitting is used,
the tool can remain charged with air after disconnecting
and thus will be able to drive a fastener even after the air
line is disconnected, possible causing injury.
Do not use any type of reactive gases, including, but not
limited to, oxygen and combustible gases, as a power
source. Use filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of compressed air may
cause the tool to explode which will cause death or
serious personal injury.
Use only a pressure-regulated compressed air source to
limit the air pressure supplied to the tool. The regulated
pressure must not exceed 110psi. If the regulator fails,
the pressure delivered to the tool must not exceed 200psi.
Over pressurizing the tool is able to result in bursting,
abnormal operation, breakage of the tool or serious injury
to persons. Use only clean, dry, regulated compressed air
at the rated pressure or within the rated pressure range
as marked on the tool. Always verify prior to using the
tool that the air source has been adjusted to the rated air
pressure or within the rated air-pressure range.
Alwaysdisconnectairsource:
1.
2.
3.
4.
Beforeunloading or makingadjustments.
Whenmaintainingthetool.
Whenclearingajam.
Whentouching the safety yoke.
Whentoolisnotinuse.
Whenmovingtoadifferentworkarea.
Warranty
6
7
LOADINGTOOL
Do not load the tool with fasteners when any one of the
operating controls is activated.
Never place a hand or any part of body in fastener
discharge area of tool.
Never point tool at anyone.
Do not pull the trigger or depress the workpiece contact
as accidental actuation may occur, possibly causing
injury.
1.
4.
2.
3.
WARNING: Thewarningsandprecautionsdiscussed
abovecannotcoverallpossibleconditionsand
situationsthatmayoccurItmustbeunderstoodby
theuserthatcommonsenseandcautionare
factorswhichcannotbebuiltintothisproductbut
mustbesuppliedbytheuser
.
,
.
Such precautionary measures reduce the risk of injury to
persons.
This warranty covers defects in workmanship or materials in this HDX pneumatic nailer kit for the one-year period from the date
f purchase. This warranty is specific to this pneumatic nailer kit. Warranties for other HDX products may vary.
Thiswarrantyappliesonlytotheoriginalretailpurchaserandmaynotbetransferred. This warranty does not cover normal
wear and tear or any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by
other than a service center authorized to repair branded air nailer. Expendable materials, such as O-rings, bumpers, driver
blades, seals, etc. are not covered by this warranty. This warranty does not apply to used in industrial
application or for rental purposes. makes no warranties, representations or promises as to the quality or performance of its
other than those specifically stated in this warranty.
HDX
pneumatic nailer kit
HDX
pneumatic nailer kit
o
HDX PNEUMATIC NAILER KIT LIMITED ONE-YEAR WARRANTY
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties of merchantability or fitness for a particular
purpose, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that
can not be disclaimed under state law are limited to one year from the date of purchase. HDX is not responsible for direct,
indirect, incidental, special or consequential damages. If this is used for commercial purposes, the warranty
will apply for ninety (90) days from the date of purchase. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
pneumatic nailer kit
1.
4.
2.
3.
5.
Thistoolkithasbeenshippedcompletelyassembled
Carefullyremovethetoolandanyaccessoriesfromthe
box
Inspectthetoolcarefullytomakesurenobreakageor
damageoccurredduringshipping
Donotdiscardthepackingmaterialuntilyouhave
carefullyinspectedandsatisfactorilyoperatedthetool
Ifanypartsaredamagedormissingpleasecall
1-800-514-6729
.
.
.
.
,
WARNING: If any parts are missing, do not operate the
tool until the missing parts are replaced. Failure to do
so could result in possible serious personal injury.
Unpacking
WARNING: Donotattempttomodifythetoolor
createaccessoriesnotrecommendedforusewith
the tool.Anysuchalterationormodificationis
misuseandcouldresultinhazardouscondition
leadingtopossibleseriouspersonalinjury.
HOMEDEPOT.COM
Please contact 1-800-514-6729 for further assistance.