FP5X Bluetooth Fish Finder User Manual
Content 1. Foreword ................................................................... 1 2. Safety Tips ................................................................ 2 3. Packing List ............................................................... 2 4. Function Description of each Part of the Fish Finder 3 5. Charging Steps ......................................................... 3 6. Introduction to the Use of Fish Finder ....................... 4 7. APP Explain .......................................
1. Foreword Thank you for purchasing our company's FP5X bluetooth fish finder. In order to ensure the correct and safe use of this product and maximize its performance, please read this manual carefully before operation。 This product is designed with a Bluetooth transfer function, which can be connected to a mobile phone. This product operates on rechargeable batteries.
2. Safety Tips Please observe the following safety tips, otherwise it may cause equipment sensitivity decline, equipment failure, and property damage: The water depth measurement and obstacle detection functions of this device cannot be used to assist navigation on the water, so as to avoid hitting rocks, damage to the boat or personal injury. If you suspect that you have entered shallow water or there are obstacles underwater, please sail with caution at low speed.
recommended); 4. Function Description of each Part of the Fish Finder 1 5 4 2 6 3 3 8 7 5 No. Function No. Function 1 Cover 5 Water switch 2 Sealing ring 6 Sonar face 3 Bottom cover 7 Antenna 4 Cover nut 8 Charging port 5. Charging Steps 5.
prepared, it is recommended to use 5V1A/5V1.5A/5V2A); 5.2 When charging, the charging indicator LED (red) will flash; when the battery is fully charged, the indicator LED will always on. 5.3 Twist the upper cover back clockwise, and turn it about two turns to get it in place. At this time, the shape of the bottom cover is symmetrical on the upper and lower sides, and the threading nuts are located on the left and right sides. At this time, you will feel that the resistance increases significantly.
Method 1: Connect the fishing line to use the cast rod; Tie the fish finder, float and bait to the fishing line and put them into the water together. When the fish finder enters the water, it will automatically start working. This product uses sonar technology, the fish finder injects ultrasonic waves into the water, and the central processor of the fish finder will filter and analyze the collected signals. The analysis results are then compiled and displayed on the mobile phone display.
the fish finder to the fishing spot. 6.2 Precautions for the Use of Fish Finder 1. When the fish finder is working, do not touch the bottom of the fish finder with your hands. Otherwise, the test results of the product will be wrong, and even the components inside will be damaged. If you want to get a working fish finder out of the water, you can grab the fish finder casing around the edges and remove it. 2. Our products can be used for a long time under normal conditions.
Put the fish finder into the water and let it float on the surface. It will scan the water bottom of the monitoring area. Bottom information will be automatically shown on the display. Once a fish enters the monitoring area, the fish symbol will appear on the display. 6.4 About the Fish Finder The fish finder consists of two parts: one part is the sonar part and the other part is the radio part. Sonar part: compile the collected signal through the radio part and transmit it to your mobile phone. 6.
same time, and it is necessary to ensure that the sonar working surface floats vertically downward on the water surface. Before use, please check whether the fishing line tied to the threading screw is in good condition. If any damage is found, please replace the fishing line. 6.7 Electronic Switch There are 2 contact terminals at the bottom of the fish finder, these 2 terminals are the electronic switch of the fish finder. The working process of the electronic switch is as follows: 1.
6.8 Fish Finder Maintenance and Storage： 1. Do not put the fish finder in a damp and watery place when not using. Otherwise, the fish finder may turn on unexpectedly, resulting in power exhaustion and other failures. Store in a dry and insulated environment. 2. Do not put the fish finder on metal objects, and do not let any metal objects touch the two electronic switch terminals, so as to avoid accidental conduction work, resulting in power exhaustion and other failures. 3.
FishPod Portable 7.
1 2 3 8 4 7 6 5 7.3 Device pairing instructions: a. Turn on the device and keep it on. b. Open the APP and automatically enter the device pairing interface (as shown below). c. APP will automatically start to scan the device, you can also click the "Search" button to scan again.
d. After the device is searched, Click "device " to connect the device and enter the main interface automatically. e. If it is a paired device, the system will automatically connect to the device and enter the main interface. f. Common problems: App can’t find the device: ◇Check if the device is turned on.
◇When you start the APP for the first time, you have forbidden some permissions. ◇Check whether the Bluetooth permission of the APP is turned on. ◇The mobile phone of Android system needs to turn on the location service, and the mobile phone pull-down setting starts the location service (GPS) After the device is disconnected, it does not automatically reconnect: ◇The device is too far away and needs to be closer. ◇The Bluetooth of the mobile phone is off, turn it on. 8.
failure. 8.3 The product cannot be stored on the metal plate, and the product should be placed in an insulated place. 8.4 Please pay attention to protect the sonar working surface to avoid bumps, scratches and impacts. Uneven and defective working surfaces will cause the performance of the equipment to decline. 9. Specifications Detection range: 0.8-60M/2.
10. Common Problems and Solutions Question Fish finder won't turn on The mobile phone cannot communicate with the fish finder Depth How to handle 1. Please confirm whether the battery power is sufficient. You can try it by charging it first. 2. Please use it at a temperature higher than -10℃. 3. After the metal terminals are polluted or corroded, the electrical conductivity will deteriorate, which will affect the startup. Please clean the exposed metal parts of the metal terminals. 4.
reading is "---" or "00.0" In shallow water, there are fish under the probe visible to the naked eye, but the host screen shows no fish The echo normally, there will be a flashing light indication. If not, it means that the fish finder is not turned on normally. 2. Please confirm that the water depth is within the range of 0.8~60 meters (2.5~200FT), which refers to the distance from the fish finder to the bottom of the water. 3.
signal is intermittent, the depth display is unstable, and the fish school cannot be displayed straight down. 2. The underwater vegetation system is too complicated, resulting in disordered depth readings. If this is determined to be the cause, it is recommended to stop using fish finders in the area. 3. Oil, dirt, etc. will form a film on the surface of the fish finder, reducing the working efficiency of the fish finder. At this time, please clean the stains on the surface of the fish finder. 4.
Temperature display is not accurate installation position of the fish finder to avoid the rapids caused by the navigation. 8. This happens when the boat speed exceeds 8 km/h. In this case, please reduce the speed of the boat. When the fish finder is moved from one temperature environment to another, the built-in temperature sensor needs a certain period of time to sense the change of the ambient temperature.
