Instruction Manual

Product Specications
Model No. HV9658-12V150W HV9658-24V150W HV9658-12V200W HV9658-24V200W HV9658-12V275W HV9658-24V300W
Material Aluminium
IP Rating IP66
Protection Class 1(Requires Earth)
Input Voltage 240v AC
Output Voltage 12v DC 24v DC 12v DC 24v DC 12v DC 24v DC
Total Load 150w 150w 200w 200w 275w 300w
Recommended Total Load 120w 160w 220W 240w
Wiring Parallel
Dimmable No
Operating Temperature -25° - + 50°
Protections Overload, Over Voltage, Over Temperature & Short Circuit
Warranty 3 Years Replacement*
150w Dimensions
247mm
233mm
Ø5mm
44.8mm
40mm
67.5mm
OUTPUT
INPUT
1000mm
500mm
Contact Details: Warranty Terms & Conditions*
HV9658 IP66 Constant Voltage LED Driver Installation Instructions
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.havit.com.au
Must be installed by a licensed electrician
Additional Information
Important Safety Issues:
• This product must be installed by a qualied electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modication of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• Aluminium and 304SS ttings must not be installed within 5km of any salt water environments.
• All Havit Lighting LED Drivers are provide with a ex & plug for ease of replacement if Driver was to fail. Removing this plug will void warranty.
• The converter must only be connected by a fully qualied electrician.
• Make sure has the correct output voltage to light source being installed.
• The installer is responsible for proper installation according to safety regulations. The primary and secondary cables have to be selected considering type and wire gauge.
Load, cable length, voltage drop and terminal characteristics have to be taken into consideration.
• Disconnect the LED Driver from the main power if its cables are damaged. - Damaged cables must be replaced.
• LED Driver can become very hot during use, Do not cover.
• The distance between the power supplies and the surfaces around must be min. 50mm so Driver is well ventilated.
• The power supply has connection cables on primary and secondary side. The secondary cables are multiple depending of the power class and are connected to the same
potential. The load has to be divided to the connection cables equally. It is not permitted to take the complete load by one single output cable, alternatively you can parallel
the 2x output cables to have full power from one connection point.
• This form may be updated at any time due to product improvements, please check online installation form for most current version.
200w Dimensions
247mm
233mm
Ø5mm
44.8mm
40mm
67.5mm
OUTPUT
INPUT
1000mm
500mm
275w + 300w Dimensions
50mm
95mm
46mm
TC
60mm
95mm
277mm
263mm
OUTPUTINPUT
1000mm
500mm
50
50
50
50
LED Driver
LED Driver
50 50
50
Top View Side View
Steps for Installation:
1. Connect the Output cable to light source making sure that polarity is correct. If
Driver has 2x Output cables, These can be joined to form one connection point.
2. If connections are outdoors make sure to cover connections using an adhesive
lined heat shrink or gel cap to make connection watertight. Failure to do this will
void warranty.
3. Make sure power is o before connecting 240v plug to power point, Once plugged
in turn power back on.
4. When LED Driver is turned on and a ticking noise can be heard. This indicates a
short on the run. Turn Driver o and inspect all connections before turning back on.
Minimum 50mm spacing needed around LED Driver.
LED Driver cannot be covered, If covered warranty will
be voided.