manual

ManualsBrandsHavis ManualsMobile PhonesC-VS-1600-EXPL-1

C-VS-1600-EXPL-1_INST_7-12.docx

INSTALL INSTRUCTIONS C-VS-1600-EXPL-1

16” VEHICLE SPECIFIC CONSOLE for

2011 - 2015 Retail Model FORD EXPLORER with OEM Center Shifter

TOOLS NEEDED:

Phillips Screw Driver

Standard Socket set

Metric Socket set

Power Drill with Drill Bits

Wire Cutters Wire Crimping tool

T-20 Torx Bit Adjustable Wrench

90° Scribe Small Screw Drivers

QTY DESCRIPTION PART #

1 Main Console Housing

1 Front hump bracket CM004244

1 Front shifter platform (attaches to hump bracket) CM004246

1 Rear mount bracket CM004239

1 Driver side trim panel CM004237

1 Passenger side trim panel CM004236

1 Top / Forward trim bezel CM004248

1 Rear control cover plate CM004317

1 Cup Holder CM001407

2 12 volt sockets CM216560

1 Aux panel adaptor plate (New for 2014) CM005898

1 Hardware kit C-HK-176

C-HK-176 Hardware Kit includes the following

10 1/4” Flat washer GSM31005

6 1/4 x 3/4” Hex head bolt GSM33001

4 1/4 x 1” Hex head bolt GSM33002

8 1/4” serrated nut GSM30023

10 # 8 x 3/8” Torx head screw CM86508

4 8/32 x 1/2” Phillips pan head machine screw GSM33110

2 # 10 x 3/4” Phillips pan sheet metal screw GSM34170

2 # 10 Speed nut GSM30199

4 Female spade connector GSM20224

2 7/8” Plug CM86430

1 3.5” (3-1/2”) diameter O-Ring GSM31331

2 1.875” (1- 7/8”) diameter O-Ring GSM31335

2 #8 X 1/4" Phillips flat sheet metal screw GSM33178

NOTES!

 Read all instructions before installing any Havis, Inc. products.

 Use hardware provided with install kit.

 Console housing is shipped partially pre-assembled to the CM004244 front hump

bracket. Bracket must be unbolted from housing prior to installation.

Summary of content (8 pages)

PAGE 1
INSTALL INSTRUCTIONS C-VS-1600-EXPL-1 16” VEHICLE SPECIFIC CONSOLE for 2011 - 2015 Retail Model FORD EXPLORER with OEM Center Shifter TOOLS NEEDED: Phillips Screw Driver Standard Socket set Metric Socket set Power Drill with Drill Bits QTY 1 1 1 1 1 1 1 1 1 2 1 1 10 6 4 8 10 4 2 2 4 2 1 2 2 Wire Cutters T-20 Torx Bit 90° Scribe DESCRIPTION Main Console Housing Front hump bracket Front shifter platform (attaches to hump bracket) Rear mount bracket Driver side trim panel Passenger side trim panel Top / Forw
PAGE 2
Optional # CM005159 (Sold separately) Top / Forward Trim Bezel -Allows C-VS-1600-EXPL-1 console to fit into Ford Interceptor Utility with Standard or Upgrade Interior. -Converts 16” inches of usable space into 24” inches of usable space. If using this part, a C-CUP2-I cup holder will be required if desired. **See Photos on last page** C-VS-1600-EXPL-1 (Main Housing Assembly) Also see complete console # C-VS-2400-INUT-1 Adaptor plate for 2014 Ford Retail Explorer.
PAGE 3
O.E.M. console prior to removal Remove one (1) screw holding top / forward trim bezel. (7mm socket) Remove Aux input jack from trim bezel assembly. To be reused later. Lift arm rest and remove (unsnap) trim piece with 12 volt socket. Unplug socket. Carefully unsnap and remove console side panels Carefully remove / unsnap trim bezel and remove terrain management switch or accessory pocket. It helps to turn ignition on and move shift lever knob rearward.
PAGE 4
Remove sensor from bottom of storage pocket. To be reused later. (10mm socket) Carefully unclip shifter cable from shifter mount assembly. This is done by pushing the two white tabs forward and sliding cable towards driver side. Both tabs need to be done at the same time. Small screw drivers can be used for this. Using a flat screwdriver, carefully pop off the shifter cable end from the linkage stud. Pop toward driver side. Unplug harness from shifter assembly.
PAGE 5
Remove console housing. Detach O.E.M. harness from console housing. To be reused. A 90° scribe works well for popping out harness clips. Remove HVAC controls from rear console housing if you desire to reuse it in the new console. The plug for this can remain disconnected if controls are not used. Remove O.E.M. forward and middle brackets from transmission hump. Save hardware. (8mm socket) Mount new # CM004244 front hump bracket to transmission hump with O.E.M screws previously removed.
PAGE 6
Attach # CM004239 rear mount bracket to existing O.E.M. rear floor bracket with two (2) previously removed bolts. (10mm) Sensor faces down. Carefully place # CM004248 Top / forward trim bezel. Do not screw down yet. Attach the supplied 3-1/2” diameter ORing to the back of the Auxiliary panel as shown. This helps make a snug fit when snapped into the console bezel.
PAGE 7
Using one (1) 1-3/4” O-Ring supplied, attach it to the back of the terrain management switch This helps make a snug fit when snapped into console bezel. ** If your vehicle only has a round accessory pocket, the pocket will need to be glued into the round hole. Attach supplied 12 volt socket into 7/8 hole in console bezel. Plug 12 volt positive wire to center connector and negative wire to outboard ground connector. Attach original plugs onto TM switch, Aux panel and snap or screw them into place as shown.
PAGE 8
Adjust position and tighten console housing to brackets. (7/16 wrench) This photo shows O.E.M. rear controls mounted in console. Four (4) 8/32 x 1/2” screws provided. Note: It is not necessary to use the controls if not desired. View of completed installation View of completed installation with Laptop computer. Before inserting cup holder, run necessary wiring and wire tie as needed. Make sure wiring is not stressed or that it does not interfere with shifter mechanism.