manual

ManualsBrandsHavis ManualsMobile PhonesC-VS-0809-CHGR-1

C-VS-0809-CHGR-1_INST_4-11

C-VS-0809-CHGR-1

(Assembly)

INSTALL INSTRUCTIONS C-VS-0809-CHGR-1

2011-2013 Dodge Charger (Police Package)

VEHICLE SPECIFIC CONSOLE

With 17” inches Equipment space

TOOLS NEEDED:

Phillips Screw Driver

Socket set (Standard & Metric)

Wire Cutters Wire Crimping tool

7/16 wrench T-20 Torx Bit

QTY DESCRIPTION PART #

1 Main Console Housing CM004345

CM004345 Main Housing Includes:

1 Floor Mount Bracket CM003956

1 Front / Center End Panel CM004380

1 Lighter Socket with cap CM216560

3 7/8” Plug CM86430

1 “O” Ring KRM98017

Not Included with CM00435 Housing, but included with complete kit:

1 Driver Side Trim Panel CM004381

1 Passenger Side Trim Panel CM004382

1 Lighter Socket with cap CM216560

1 Sensor Cover CM001638

1 Hardware kit C-HK-174

CM004380

Front / Center End Panel

CM004345

Main Console Housing

CM004381

Driver Side Trim Panel

CM003956

Floor Mount Bracket

ALWAYS!

* Read all Instructions before installing any Havis, Inc. products.

* Use Hardware included with install kit

CM004382

Passenger Side Trim Panel

NOTE:

If your vehicle has the optional carpet interior, there will be a small

hole in the carpet not covered by the console housing at the rear.

If desired, an optional cover plate part number - CM001642 is available.

Cover plate not shown.

Summary of content (4 pages)

PAGE 1
INSTALL INSTRUCTIONS C-VS-0809-CHGR-1 2011-2013 Dodge Charger (Police Package) VEHICLE SPECIFIC CONSOLE With 17” inches Equipment space TOOLS NEEDED: Phillips Screw Driver Socket set (Standard & Metric) QTY 1 1 1 1 3 1 1 1 1 1 1 Wire Cutters 7/16 wrench Wire Crimping tool T-20 Torx Bit DESCRIPTION PART # Main Console Housing CM004345 CM004345 Main Housing Includes: Floor Mount Bracket CM003956 Front / Center End Panel CM004380 Lighter Socket with cap CM216560 7/8” Plug CM86430 “O” Ring KRM98017 Not Inclu
PAGE 2
O.E.M. console prior to C-VS-0809-CHGR-1 console installation. Remove O.E.M. plastic center console Remove forward O.E.M console plastic cover and remove two (2) nuts from front floor bracket. Nuts to be reused. (10mm) Remove bolts that hold underside of extrusion to rear floor bracket. (7/16 wrench) Remove rear floor bracket bolts and center console bolt. (10mm) Remove Ignition proximity sensor / antenna from rear underside of O.E.M. console.
PAGE 3
Loosely attach previously removed nuts onto front floor studs. (10mm) Loosely attach rear of console to existing floor inserts. Inserts located under rubber mat as shown. Use OEM screws (if provided) or 1/4 x 3/4 self threading screws (included in hardware kit) to mount rear of console. (7/16 wrench) “O” Ring shown partially on Push Console assembly forward and tighten all floor mount bracket hardware. Run all wiring as needed. Place # KRM98017 Rubber “O” Ring onto AUX socket assembly.
PAGE 4
A cover is provided to guard the O.E.M. Sensor on transmission hump. If desired, attach to existing stud and 6mm nut and washer provided. Console assembly complete with Docking Station. Prior to installation of control heads and accessories, determine desired position and attach Tilt/Swivel and Docking Station bracket.