Owner's manual
81
IND100129-175
All specifications are subject to change without prior notice!
High Bright model
Specications - HD 19T21 MMD-xxx-FHxx
SPECIFICATIONS
Note: All specifi cations are subject to change without prior notice!
Please visit www.hatteland-display.com for the latest electronic version.
2/2
• High Quality TFT with LED Backlight Technology
• Sunlight Readable / High Bright (includes Optical Bonding Technology)
• 19.0 inch viewable image size, Aspect Ratio 5:4
• TFT active-matrix liquid crystal panel
• MVA (Multi-domain Vertical Alignment) LCD Technology
Multi-power Supply:
• 115&230VAC - 50/60Hz + 24 VDC - HD 19T21 MMD-Mxx-FHxx
Note: You may connect either AC power or DC power or both. In case both sources
are connected, power will be sourced from the AC input. If AC input is lost, there will
be a uninterrupted switch-over to DC input.
Power Consumption:
• Operating : 72W (typ) - 125W (max)
A P P R O V A L S & C E R T I F I C A T E S
Physical Considerations:
TFT Technology:
TFT Characteristics:
Power Specifications:
This product have been tested / type approved by the following classification societies:
IEC 60945 4th (EN 60945:2002) IACS E10 ClassNK - Nippon Kaiji Kyokai
GL - Germanischer Lloyd DNV - Det Norske Veritas ABS - American Bureau of Shipping
CCS - China Classification Society BV - Bureau Veritas LRS - Lloyd’s Register of Shipping
EU RO MR - Mutual Recognition
Compass Safe Distance: HD 19T21 MMD-xxx-FHxx Standard: 125cm Steering: 75cm
• Digital separate synchronization
• Composite synchronization
• Synchronization on green
• Auto detects VGA -> SXGA, interlaced and non interlaced
• Video Signal : Analog RGB 0,7Vp-p
: Input Impedance 75 Ohm
Synchronization Range:
• Horizontal : 31.5 kHz to 91.1 kHz
• Vertical : 60 Hz* to 85 Hz
* Recommended for optimum picture quality
Resolutions:
• VGA : 640 x 480 (including 640 x 350)
• SVGA : 800 x 600 (including 720 x 400)
• XGA : 1024 x 768
• SXGA : 1280 x 1024*
* Recommended for optimum picture quality
Video Signals:
• Interlaced HDTV, NTSC, PAL and SECAM video
• Composite video
Synchronization:
Supported Signals:
• DVI-D Signal IN : 2 x 24p DVI (female)
• RGB Signal IN : 2 x 15p HD D-SUB (female)
• Comp. Video IN : 3 x BNC Connector (female)
• SCOM RS-422/485 : 1 x 5-pin Terminal Block 3.81, non-isolated+Buzzer
• RGB Signal OUT : 1 x 15p HD D-SUB (female) - Clone of RGB IN*
• If Touchscreen : 1 x USB TYPE A Connector. (female)
• Ethernet : 1 x RJ45 Connector for Remote Control
• SCOM RS-232 : 1 x 9p D-SUB (female) non-isolated
• Potmeter : 1 x 9p D-SUB (male)
(Potentiometer IN, +5VDC OUT, BRT +/- IN)
• AC Power IN : 1 x Std IEC Inlet
• DC Power IN : 1 x 2-pin Terminal Block 5.08
*Tested at recommended resolutions. The RGB output signal is at same resolution and
sync as the RGB input. The output is working even if the display unit is turned off, but
power cable/supply must be connected/provided.
Signal Terminals:
• Operating : Temperature -15 deg. C to +55 deg. C
- Humidity up to 95%
• Storage : Temperature -20 deg. C to +60 deg. C
- Humidity up to 95%
• IP Rating : Protection: IP66 front - IP22 rear (EN60529)
Lifetime Considerations:
Even although the test conditions for bridge units provide for a maximum
operating temperature of 55°C, continuous operation of all electronic
components should, if possible, take place at ambient temperatures of only
25°C. This is a necessary prerequisite for long life and low service costs.
Behind front bezel - Glass Display Control™ (GDC) IP66:
• Power On/Off, On Screen Display Menu, Brightness Control (-/+)
• Hotkeys (left/right), Mode Status Indicators (ECDIS, Service)
• Buzzer (not visible), Light Sensor (not visible)
• Projected Capacitive Touch Screen (Multitouch, USB interface)
• Color Calibrated models (ECDIS)
Environmental Considerations:
User Controls:
Factory Options:
For a full overview of typenumbers, please review the following link:
www.hatteland-display.com/pdflink/ind100780-3.php
• HD CMB SX1-A1 : 1 x Console Mount Kit (3-12mm). EN60945 Tested
• HD CMB SX1-A2 : 1 x Console Mount Kit (1-12.75mm). EN60945 Tested
• HD CMB SX1-A3 : 1 x Console Mount Kit (1-12.75mm). EN60945 Tested
Long screws for easier installation in tight spaces.
• HD TMB SX1-B1 : 1 x Table Mount Bracket. EN60945 Tested
• HD VED SX1-A1 : 1 x VESA Bracket, not EN60945 Tested
• JH 19TAP STD-C1 : 1 x Frame Adapter (19" Series 1 to Series X) retrofit
Please see user manual/datasheet for more information
Available Accessories:
• Native Resolution : 1280 x 1024
• Pixel Pitch (RGB) : 0.294 (H) x 0.294 (V) mm
• Response Time : 20ms (typical), “black” to “white”
• Contrast Ratio : 1000:1 (typical)
• Light Intensity : 800 cd/m² (typical)
• Viewable Angle : +/- 89 deg. (typical) (Up/Down/Left/Right)
• Active Display Area : 376.32 (H) x 301.056 (V) mm
• Max Colors : 16.7 million
• W:429.00 [16.89''] x H:382.00 [15.04''] x D:81.50 [3.21''] mm [inch]
• 4 x M6 VESA mounting 280x150mm, Max 12mm deep
• Weight: 8.2kg / 18.0lbs
• Delivery includes an EPDM sealing gasket for IP66 console mount.