User Manual

HATER
PAIN
TBALL
“HATRED NXT/SFT
Shocker Board”
HATRED Software
Version 4
Featur es:
 Designed from the ground up for both the Shocker SFT and
Shocker NXT.
 The first ever paintball circuit board with a fully integrated
wireless transceiver!
 Fully compatible with all SYMBIO wireless products.
 Includes 22 firing modes including fully customizable ramp
modes.
 Compatible with both reflective and break-beam Shockers.
 Proprietary multi-tasking algorithms continuously monitor all
trigger and eye events to ensure that all pulled shots register
and are processed.
 TEN TIMES faster than the top-ranked competitor! This
translates to 900,000 more operations per second than
anyone else.
 Gold plated leads ensure rock solid intra-circuit
communication.
 Fully adjustable ABS features add to the marker’s dwell to
eliminate that pesky first shot drop-off.
 Anti-mechanical bounce (AMB) algorithms solve the
problem of physical switch bounce. No need to worry when
the refs pull that old slow trigger pull trick on your gun.
 A “forced shot” feature allows the user to clear the marker of
eye faults.
 Instant on feature. After all, you wanna play now!
 Instantaneous battery status.
 Tournament lock feature allows the user to “lock out” the
programming mode in order to meet specific
field/tournament guidelines.
Installation:
MAKE SURE THE MARKER IS NOT CONNECTED TO AN AIR
SOURCE AND DOES NOT HAVE PAINTBALLS IN THE BREACH
DURING INSTALLATION!!!!!!
1. Remove the screws that secure the grips. This will expose
the board.
2. Carefully remove the two pins behind the trigger. These
pins go through the microswitch and mount the circuit board
to the frame.
3. Unplug the battery and wiring harness from your old board.
4. Plug the wiring harness into your new HATRED board.
5. Carefully place the new HATRED board into your frame and
reinsert the mounting pins through the microswitch.
6. Attach a fresh 9v battery and insert the battery into the
frame. Make sure the leads from the battery are tucked
away from the circuit board and towards the rear of the
frame. Be very careful not to scratch the back of your
circuit board with the battery. Circuit boards which are
damaged due to incorrect installation are not covered
under warranty.
7. Replace grips.
8. VERY IMPORTANT. Enter the programming menu and set
your eye type (break-beam or reflective) before you use the
marker. Please see the “programming” and “eye sensor
operation” headers on how to do this.
9. Power on and play!
LED’ s:
The HATRED gun board has two LED’s. The button LED is a single
color, blue LED that is seen through the Shocker’s rear button. The
onboard LED is a multi-color LED that is physically mounted on the
bottom of the HATRED Shocker board. We suggest using translucent
grips so you can see the onboard LED as it makes the programming
and operation of your marker much easier.
Power :
Power On: The HATRED board comes equipped with an Instant On
feature. Simply press the power button and your marker will instantly
power on. As long as the power button is depressed, you will see a
flickering GREEN or RED led on the Onboard LED. The GREEN
indicates a good battery and the RED means replace the battery as
soon as possible. Regardless of GREEN/RED battery indication, your
marker WILL REGISTER YOUR FIRST TRIGGER PULL! Please be
careful!
Power Off: To turn the marker off, press and hold the button for two
seconds. As the gun powers down, the onboard LED will go through a
rainbow power down sequence. Please note that this particular rainbow
LED sequence does NOT indicate that you’re entering the programming
menu.
Pr ogr amming
The bottom dip switch must be in the OFF position in order to enter the
programming menu. If the bottom dip switch is ON, “tournament lock”
will be enabled and the user will be unable to program the marker.
To enter the programming menu, hold the trigger down and THEN turn
the marker on. The onboard LED will inform the user that the
programming mode has been accessed by flashing several colors
rapidly.
LED
Col or
Setti ng
Defaul t
Setti ng
Adj ustabl e
Range
Purple
Fire Mode
1
1-22
Green
Debounce
5 ms
1-50 ms
Red
Dwell
14 ms
5-35 ms
Blue
Max ROF
20 cps
10-35 cps
Teal
AMB
1 ms
1-60 ms
Yellow
Eye Delay
4 ms
1-20 ms
White
Wireless
Address
1
1-32
Flickering
Purple
ABS
10 ms
1-20 ms
Flickering
Green
Ramp
Activation
9 bps
6-15 bps
Flickering
Red
Ramp
Percent
10%
1-20
(10-200%)
Flickering
Reset
n/a
n/a
Blue
Defaults
Fickering
Teal
Eye Type
1
1➠Breakbeam
2➠Reflective
1.) Pulling and releasing the trigger will allow the user to toggle
through the different programming options.
2.) Once the desired setting/LED color is reached, pull and hold the
trigger to select that setting. The onboard LED will then go blank.
3.) Once the onboard LED goes blank, pull the trigger for the desired
setting. For example, if the user wishes to set the debounce to 2,
he or she must pull the trigger two times.
➠If the user wants to view their current value for a particular
setting, he or she need only to continue holding the trigger in after
the setting is selected from the menu. The software will then
blink back the user’s current value for that particular setting.
4.) The software will indicate that the new value has successfully
been entered by blinking the value back to the user then rapidly
flashing the LED through a spectrum of colors.
➠As the software blinks back the new setting, the user may abort
this process by simply clicking the trigger once. The new settings
will still be saved.
5.) After a setting has been changed, the user may change another
option or power the gun off to save the settings.
NOTE: All “programming clicks” correspond exactly to their settings. If
you want to cap the ROF at 15, pull the trigger 15 times. If the user
sets the value too low (2 cps ROF cap for example), the software will
automatically default to the lowest accepted value. The inverse is also
true for user inputs which are beyond the adjustable range.
Pr ogr amming Ex amples:
To set the firing mode to PSP mode.
1. Turn the marker off.
2. Hold the trigger down; then turn the marker on. Once the LED flashes many
colors, release the trigger.
3. Tap the trigger until the LED turns purple.
4. Hold down the trigger until the LED goes blank.
5. Tap the trigger two times.
6. Once the LED flashes many colors, turn the marker off.
To set the eye type to reflective.
1. Turn the marker off.
2. Hold the trigger down; then turn the marker on. Once the onboard LED
flashes many colors, release the trigger.
3. Tap the trigger until the onboard LED turns flickering teal.
4. Hold down the trigger until the LED goes blank.
5. Tap the trigger 2 times.
6. Once the LED flashes many colors, turn the marker off.
To set the max ROF to 15 bps.
1. Turn the marker off.
2. Make sure the top dipswitch (dipswitch 1) is in the ON/UP position.
3. Hold the trigger down; then turn the marker on. Once the LED flashes many
colors, release the trigger.
4. Tap the trigger until the LED turns blue.
5. Hold down the trigger until the LED goes blank.
6. Tap the trigger 15 times.
7. Once the LED flashes many colors, turn the marker off.
Dip Sw itch Settings:
Switch
UP
DOWN
1
(top)
ROF Cap ON
ROF Cap OFF
2
(bottom)
Tournament
Lock
Programming
Mode
Eye Sensor Oper ation: