This manual is a provisional version only.
This manual is a provisional version only.
This manual is a provisional version only. Congratulations! Welcome to the Hasselblad H System. The H2D adds the ability to utilize the latest advancements in digital backs, increased mobility, integrated power, and improved image quality. The H2D is the most advanced digital medium-format photography platform on the market today, and a worthy addition to the famed Hasselblad line. The specifications and capabilities of the H system exceed the demands of most photographers.
This manual is a provisional version only. ing, TTL flash control, capable of saving to internal CF cards and external storage devices, presentation of digital information such as histograms and grey balance on the LCD, extremely accurate electronic leaf shutter, flash sync at all shutter speeds to 1/800s, eyeline viewfinder with 100% view, dot matrix viewfinder LCD, lithium or rechargeable battery options, shutter speeds from 32 seconds to 1/800s, user customization of functions.
This manual is a provisional version only. What’s in the box Your new Hasselblad camera may have been supplied in kit form or as separate items. There are a number of possible combinations depending on factors such as offers, bundles etc. Please ensure that all the items noted on the accompanying packing information have been supplied and are correct.
This manual is a provisional version only. 1 Quick Start This section is a quick start guide to assembling and preparing your new H2D. From separate items, the assembly process should take no more than several minutes to complete and when the battery is charged you will be able to take simple and straightforward photographs immediately. All the information is repeated later on in the manual, as well as much more in-depth information, under the relevant sections and headings for easier search access.
This manual is a provisional version only. H2D 2 1 An H2D can be used in a variety of ways but for simplicity’s sake below is a description of how to use it with a CF card. Naturally you can skip this section if you wish and go directly to the appropriate section in this manual regarding tethered use etc. 3 1 1. Remove the battery by depressing the battery holder button and simultaneously swinging the battery holder retaining lever down until it stops. Pull battery downwards. 2.
This manual is a provisional version only. 13 14 15 16 17 18 13. While holding the viewfinder at a slight angle, locate the front section into place on the front edge of the viewfinder screen recess in the camera body ensuring the central locating lug and databus interface are positioned correctly. Swing the viewfinder downwards and press firmly until it clicks into place. Ensure that both sides of the viewfinder are seated correctly. 14. Point the camera at a smooth toned area.
This manual is a provisional version only. Familiarize yourself with the H2D Take a few minutes to familiarize yourself with the H2D and its various controls. Note the difference between a long press, a short press and a ’click’ with some buttons. For example from the main screen a click of the ON.OFF button will take you to Profiles while a longer press will turn the camera off.
This manual is a provisional version only. 2 Function Control & Display ■ LCD display on camera ■ LED display on viewfinder ■ OLED display on sensor unit ■ Upgradeable firmware ■ Rapidly accessible menu ■ Interactive display ■ Customizable functions All functions and settings on the H2D are accessed and altered by the control buttons and wheels on and around the grip aided visually by the LCD userinterface.
This manual is a provisional version only. Below is an overview of the primary functions of the control wheels and buttons. Some controls have dual or triple functions according to the state of the menu or setting. A full description can be found further on in this manual. Shutter release button Activates camera and releases shutter. FLASH / (CONTROL LOCK) button Lock settings to avoid inadvertent change. Also accesses flash settings. AF button Accesses focus modes.
This manual is a provisional version only. Grip LCD Typical camera grip display. (The information in brackets describes this particular example). Flash condition indication (No exposure compensation, normal flash synchronisation) Focus setting (Autofocus setting, single shot mode) Drive condition (Single setting) Shutter speed setting (1/400s) Aperture setting (f/5.6) ISO setting (50 ISO/ASA) Exposure Value display (EV 9.
This manual is a provisional version only. The basic principle behind making changes is that the appropriate button is first pressed to access the menu and then settings altered by way of the control wheels. The appropriate control wheel is designated by arrowheads alongside the setting description. Some buttons have a toggle function, the ON.OFF button has a quick ‘click’ action as well as a longer (half-second) ‘press’ action and the shutter release has two positions: ‘half-press’ and ‘full-press’.
This manual is a provisional version only. Viewfinder LCD Typical viewfinder display. Note the LEDs will only be visible when activated (by the camera or a setting). (The information in brackets describes this particular example). Exposure method indication (‘aperture priority’ mode) Aperture setting (f/5.
This manual is a provisional version only. Menu charts – general The H2D features the advantage of multiple customization of settings. This means that your personal choice of settings, and thereby appearance of various combinations of symbols on the LCD at any time, will not necessarily be the same as many of the screens illustrated in this manual. Throughout this manual you will find charts to explain the steps and procedures required to alter the various settings.
This manual is a provisional version only. Shutter release button A A This button has half-press and full-press positions. By pressing half-way (or softly) the camera, auto focus function and exposure meter can be activated. By pressing all the way down (or more firmly) the shutter will be released (or the chosen exposure procedure will begin, as relevant. For example, the self timer is activated with this button) FLASH / (CONTROL LOCK) button / (EXIT) B This is a triple function button.
This manual is a provisional version only. On the rear of the grip, as well as the rear control wheel, there are a further three control buttons: AE-L button J K L J This button can lock a light reading made in both automatic and manual exposure modes. It can also be used in Zone mode to take a new reading. Can be reassigned in Custom Settings to another function. See section on the AE-L button (chapter 8, Light Metering and Exposure Control) for full details. button K No function at present.
This manual is a provisional version only. There are also two control buttons on the viewfinder, as well as the eyesight correction adjustment wheel: Eyesight correction adjustment wheel P The personal eyesight adjustment facility has a diopter range of -4 – +2.5, to suit most users. EV correction adjustment button Q Press this button to access the EV compensation screen. Settings are made with either the front or rear control wheels.
This manual is a provisional version only. 3 Camera Body ■ Aluminium cast in one piece ■ Stainless steel shell ■ Integral Quick coupling plate ■ Digitally controlled ■ Upgradeable software ■ Modular design ■ Integral ergonomic grip ■ Pixel based LCD user interface The H2D camera body is a robust construction of cast aluminium with a stainless steel shell for extreme durability.
This manual is a provisional version only. 1 Carrying strap 2 1, 2 The carrying strap is attached by firstly withdrawing the safety collar. The hook is then freed and attached to the strap lug (fig. 1). Slide back the safety collar (fig. 2) to ensure the hook remains in the locked position between the small protruding lugs. The collar is purposely a tight fit and might need some effort to slide. Rechargeable battery grip 3 The H2D requires battery power for all actions.
This manual is a provisional version only. Attaching the battery to the camera 8 8 Holding the battery holder flat against the grip and aligning the two upper lugs with the slot in the grip, slide it back into position as far as it will go. Swing back the battery holder retaining lever until it clicks back into place. Please note if you want to use the rechargeable battery with an H1/H1D model, the firmware in the camera must be version 8.2.2 or later for the battery grip to function properly.
This manual is a provisional version only. Reserve lithium battery grip 9 10 The reserve lithium battery grip is attached and removed in the same manner as the rechargeable grip. Press the red battery cassette retaining button inwards on the holder to release the battery cassette (fig 9). Load three CR-123 lithium (or equivalent) into the cassette, ensuring the polarity of each battery is correctly oriented (see the ‘+’ markings on the batteries and the cassette) (fig 10, 11).
This manual is a provisional version only. Accessory connection 16 17 16, 17 On the left hand side of the camera body are two accessory retaining screw threads (M5), as well as a databus connector, protected beneath a cover. The screw threads are a future-safe design feature for new products while the connector is for service purposes only. The cover can be removed by inserting a pointed object, such as a pen, in the small hole and then sliding it to the left, as in the illustration.
This manual is a provisional version only. 4 Viewfinder ■ Multi-mode light metering ■ Full exposure information ■ 100% image ■ 90° viewing angle for eye-line composition ■ Full image for spectacle wearers ■ Integral dioptre adjustment ■ Integral flash unit The 90° viewfinder provides a laterally corrected 100% image at eye-line level. It features a wide-range diopter adjustment to suit most users. The viewing distance is designed to provide full frame view even for eyeglass wearers.
This manual is a provisional version only. A B C D E F G H Parts & Components A. B. C. D. Rubber eye cup Hot shoe Eyesight adjustment wheel Exposure compensation button E. F. G. H.
This manual is a provisional version only.
This manual is a provisional version only. 1 Parts and components 2 A A. B. C. D. E. B C 2 D 1 E 3 1 Lens shade index Manual focus ring Focusing distance scales Depth-of-field scales Lens index Attaching a lens 2, 3 Remove the front protective cover on the camera body by depressing the lens release button and keeping it depressed while turning the cover counter-clockwise. Remove the rear lens cap by unscrewing it in a counter-clockwise direction.
This manual is a provisional version only. Depth-of-field calculation 7 There are two distance scales (in feet and metres) visible through the focus distance window on the upper part of the lens barrel. There is also a central lens index mark and a depth-of-field scale. The focusing distance is read off the chosen scale from the central lens index. Depth-of-field can be calculated as follows: 1. Focus the lens as required. 2. Make an exposure reading (auto or manual) and note the aperture setting. 3.
This manual is a provisional version only. is incorrect if only one arrowhead is visible. If the focus cannot be established, then both arrowheads flash. CF Adapter The CF adapter is an optional accessory that allows virtually all C type lenses from the V-system to be used on H-system camera bodies. This automatically expands the potential lens range for H cameras by more than a dozen different focal lengths. The automatic focusing system in the H camera can be used as a guide for manual focus setting.
This manual is a provisional version only. 7 Sensor unit & Digital capture ■ 22 million pixels for high end results ■ 3 operating and storage modes ■ Direct shooting to Adobe DNG ■ FlexColor worklow efficiency ■ Instant approval architecture The H system cameras were designed with digital photography in mind right from the outset so the H2D is a natural development within the world famous H system.
This manual is a provisional version only. The sensor unit houses the CCD; the digital capturing component of the H2D camera. This light-sensitive element is called an area array CCD (charge coupled device), which acts as computer-readable electronic ‘film’. The surface of the CCD has 22 million light-sensitive areas, each of which creates a pixel in your final digital image. In a colour digital image each pixel has three colour components: red, green and blue (abbreviated RGB).
This manual is a provisional version only. A F B G C H D I E J The Control Panel The control panel with its bright OLED screen is the main graphical interface for image checking and sensor unit setting changes when not connected to a computer. However, the grip LCD is still the interface for focus and exposure settings. The buttons are used for browsing images and navigating the menu system.
This manual is a provisional version only. Approve / (OK) button H This button steps through the three approval levels, thereby assigning an approval status to the image currently displayed (or selected) in the preview screen. (part of the Instant Approval Architecture system). Also acts as a confirmation button (OK button) for some types of menu operations, such as deleting images; indicated by a label beside the button on the preview screen.
This manual is a provisional version only. System Requirements Whichever mode you choose, final image-storage and correction requires a certain minimum standard regarding computer capabilities. Large images will require a highperformance computer with plenty of memory, advanced graphics capabilities and a recent operating system. In most cases, you will want your computer to include a FireWire connector, which will enable you to load images directly from the camera or ImageBankCF.
This manual is a provisional version only. Shooting Selecting the current medium The current medium selection is the location to which new shots are saved and from which you can browse using the navigation button. In many cases, the destination medium is selected automatically, for example: • When you are connected to a computer, then images are always saved directly to the computer hard disk. • When only one medium is connected (e.g., a compact-flash card), then this medium is automatically selected.
This manual is a provisional version only. 3. Tethered / Studio mode This mode enables you to connect your camera directly to a computer and to operate the system using Hasselblad FlexColor software and store images on a computer hard-disk. • The main advantages with this mode are the almost limitless storage capacity and being able to work on the images (with Hasselblad FlexColor) on a large screen. • The main disadvantage with this mode is the lack of mobility to any great extent.
This manual is a provisional version only. 4 sensor unit with your fingers. As you do this, the card will be pushed out a few millimeters. 5. Grasp the card between your thumb and forefinger and pull it away from the sensor unit. (Insert a new card as described in “Inserting a Card”, if required). 6. Snap the slot cover shut again. Working with an ImageBank CF 5 The Ixpress Image Bank CF is an optional add-on for the H2D.
This manual is a provisional version only. Tethered to a computer When tethered to a computer, you can control many camera functions using the FlexColor software. Even if you never shoot while connected, you will probably connect the camera to your computer each time you want to download your images, though you might instead use a compact-flash card reader and/or connect your Image Bank CF or FireWire disk directly.
This manual is a provisional version only. Removing from a computer To remove the camera from a computer, simply disconnect the FireWire cable. Initial general settings Setting sensitivity (‘speed’) and white balance (‘colour temperature’) The two digital settings that are most relevant for taking pictures are: • the ISO setting and • the white balance setting These are therefore available at the top level of the menu system so you can get to them quickly and easily.
This manual is a provisional version only. To set the rating, use the MAIN MENU > White Bal entry in the sensor unit menu system. See MAIN MENU > White Bal for complete details, including detailed descriptions of the presets and other options. or Make a setting on the camera grip menu. (MENU > DIGITAL > White balance) Working with media and batches Whichever way you choose to store your images, they should be filed in batches for efficient workflow.
This manual is a provisional version only. 1 2 3 4 5 6 7 2. The screen now shows a list of media devices currently connected to the sensor unit. Often, there is only one. Each medium shows a name, total size and an estimate for how many images will fit on it. To the right of the medium name is a set of three coloured numbers in parentheses. These indicate the total number of images of each approval status (green, yellow and red) that currently exist on that medium.
This manual is a provisional version only. Medium-type icon (Compact Flash) Medium name Creation date Number of green, yellow and red shot s currently stored on the medium The MEDIA list. In this example a CF card and a FireWire disk are illustrated and therefore connected. The blue frame around the CF card symbol tells you that captured images will be saved to the CF card and not the FireWire disk.
This manual is a provisional version only. Using Instant Approval Architecture The Instant Approval Architecture system helps you to evaluate your images as quickly as you take them. It works by supplying immediate audio feedback, which tells you instantly whether each new picture is exposed correctly or likely to be over- or underexposed. Thereafter, the system enables you to assign each image one of three status levels.
This manual is a provisional version only. 3. If no problem is detected, then the image is saved with green status. If you set Approval to ‘Auto’, all images will be stored as Green if judged as correct and Yellow if judged as technically doubtful. No images are ever stored as Red automatically! 4. When you are browsing through your shots, keep an eye on the approval status of each and consider whether you should promote or demote each shot based on its appearance on the preview screen.
This manual is a provisional version only. • If you are running out of space, set the filter to show only red images and then step through to find shots you can delete. • Set the filter to show only green images. Then step through to make sure you have at least one ‘good’ example of each shot that you need. There are two ways to set the browse filter: • Press and hold until the filter you want to use is shown by the indicator (see also page 44). • Use the MAIN MENU > Browse entry of the menu system.
This manual is a provisional version only. Viewing, Deleting and Transferring Images Basic image browsing The large, full-colour OLED display enables you to inspect your shots while you are still on-location. The display offers full-screen previews, high-magnification zoom, two levels of thumbnails and analysis tools including a full histogram and camera settings.
This manual is a provisional version only. 3 or or 3. You can now do the following as needed: • Use the navigator button to move the zoom area if you wish to inspect a different part of the image. • Zoom further by pressing the zoom-in (+) button more times. • Zoom back out one step by pressing the zoom-out (-) button. 4. When you are done, press and hold the zoom-out (-) button to return to browsing at the standard zoom level.
This manual is a provisional version only. Preview Modes Choosing the Preview mode You can use the view-mode button to cycle through the available preview modes. The preview screen works in several different modes: • Standard preview: shows a preview image surrounded by a display of few important settings. • Histogram: shows a preview image overlaid with a histogram. • Histogram and full details: shows a preview image overlaid with both a histogram and camera-setting details.
This manual is a provisional version only. The standard preview display The standard preview display is the one shown when you first turn on the camera. It features a preview of your most recent shot and basic information about the sensor unit settings and the image itself. Using the histogram The histogram provides a graph that indicates the total number of pixels at each brightness level, with brightnesses going from black on the left to white on the right.
This manual is a provisional version only. Battery-saver mode In this mode, the sensor unit is fully responsive, so you can take pictures but the screen is not lit up, thereby saving battery power. You can enter the menu system while shooting in this mode (which activates the screen until you exit the menu system again) but the approval, zoom and navigator buttons have no effect.
This manual is a provisional version only. Deleting images The sensor unit enables you to delete images using any of the following techniques: • Delete the currently selected image only.
This manual is a provisional version only. Transferring Images Transferring to a computer To transfer images stored on the compact-flash card to your computer, simply connect the camera to a computer using a FireWire cable and then run FlexColor, which will automate the process. See your FlexColor manual for details. See also Connecting to the Computer for details about how to connect to a computer.
This manual is a provisional version only. Working with the menus The preview screen on the sensor unit enables you to view your images and navigate the menu system through which you can make sensor unit settings. Some of the settings provided by the sensor unit menus can also be made using the controls on the grip. For settings available in both places, it does not matter whether you use the sensor unit menus or camera body menus—the effect is the same.
This manual is a provisional version only. 1. Press the menu (MENU) button to open the menu. 1 2. Use and to select the SETTINGS sub-menu. 2 3. Press to open the SETTINGS menu. 4. Use and to select the USER INTERFACE sub-menu. 5. Press to open the USER INTERFACE menu. 3 5 6. Use and to select the Language entry, which shows the current language setting. • At this point, you will use the (+) and/or (-) buttons to choose a setting for the selected entry.
This manual is a provisional version only. Menu system overview The main menu contains those settings that you will need to access most often as you work on an assignment. It also provides sub-menus that give you access to all other settings, most of which you will need less often. The ISO Setting You are able to set the light sensitivity of the camera to match an equivalent ISO rating for standard film.
This manual is a provisional version only.
This manual is a provisional version only. To select the medium to which to save new shots and from which to browse previous shots: 1. Select the MAIN MENU > MEDIA entry. The current setting is displayed here. (See also Navigating the Menu System for details about how to find this setting.) 2. Use the (+) and (-) buttons to step through the available media until the name for destination/source you wish to use is shown. 3. Either move on to another setting by using the navigator button, or: 4.
This manual is a provisional version only. MAIN MENU > STORAGE > Delete 1 Use the MAIN MENU > STORAGE > Delete menu to delete images that you do not need, thereby making room for more captures. There are several ways to delete images: • Delete a single selected image • Delete all images from a given batch • Delete all images from a given medium • Delete all images of a specified approval status (e.g., red) from a given batch or medium.
This manual is a provisional version only. Menus for deleting several images from a selected batch. Deleting several images from a selected batch 1 To delete several images from a selected batch: 1. Starting at the single-image preview display, Select MAIN MENU > STORAGE > Delete. (See also Navigating the Menu System for details about how to find this setting.) 2. Use to to enter the Delete submenu. 2 3.
This manual is a provisional version only. 4. Press OK to confirm the delete. To exit without delete, press EXIT. 4 5. You now return to the main menu. Either move on to another setting by using the navigator button or 6. Press the menu (EXIT) button to exit the menu system.
This manual is a provisional version only. Menus for deleting several images from all batches from a selected storage medium. 1 2 Deleting several images from a selected medium To delete several images at once: 1. Starting at the single-image preview display, press the zoomout (-) button three times to go to the list of media. 2. Use and to select the medium from which you wish to delete. You will be deleting from all batches stored on that item.
This manual is a provisional version only. 5 5. You must now select the approval status that you wish to delete. All images from the selected medium that are also of the status that you select here will be deleted by the operation. Use and to select All Red, All Red & Yellow or All. 6 6. Then press to open the delete dialog for your selected status. 7 7. You are now asked to confirm the delete.
This manual is a provisional version only. Sensor unit Setting Usage comments Sunlight For general outdoor use in direct sunlight. Cloudy For general outdoor use in cloudy weather. Shadow For general outdoor use in shady locations out of direct sunlight. Flash For general indoor use when using a typical flash system. Fluorescent For use when using fluorescent lighting. Tungsten For use when shooting indoors under standard tungsten lamps.
This manual is a provisional version only. Using the preset white balance functions 1 To select a preset white balance: 1. Select the MAIN MENU > White Bal entry. The current setting is displayed here. (See also Navigating the Menu System for details about how to find this setting.) 2. Use the (+) and (-) buttons to step through the available white balance settings until the setting you want is shown. 3.
This manual is a provisional version only. User interface settings (1 - 99, Never) MAIN MENU > SETTINGS > User Interface The User Interface settings control the way the sensor unit interacts with you, the photographer. It also presents some battery-saving options and includes date and time settings. Entries of the USER INTERFACE Menu To get to the user interface settings, open MAIN MENU > SETTINGS > USER INTERFACE menu. The user interface menu includes both entries and sub-menus.
This manual is a provisional version only. Navigating the date and time settings 2005 - 2100 1 - 12 1 - 31 0 - 23 0 - 59 Setting the Date & Time 1 The sensor unit has an internal clock that keeps track of the date and time. These are used to mark each shot with the date and time at which it was taken. They are also used to label batches with the date on which each batch was created. Note that the date and time are synchronized to your computer whenever you connect it to your sensor unit.
This manual is a provisional version only. Navigating the display settings 0 - 99 min, Off 0 - 10 0 - 10 Making Display settings The Display settings control the brightness and contrast of the display. They also enable you to set a time-out for the display, which works somewhat like a screen saver and can help you save battery power. 1 2 To set the display options, open the MAIN MENU > SETTINGS > USER INTERFACE > DISPLAY menu.
This manual is a provisional version only. Navigating the storage settings MAIN MENU > Storage 1 The Storage menu provides entries for working with storage media. Here, you can format media, copy images from the camera to a hard disk or computer and create new batches on available media. You can also set the initial approval status (green or yellow) assigned to new pictures.
This manual is a provisional version only. The Format command 1 The sensor unit is only able to read and write to media that have been initialized to use the FAT32 format, which is also readable by both Windows and Macintosh operating systems. However, new cards or disks sometimes arrive without any formatting, or you might want to convert media that are currently using a format that the camera cannot read.
This manual is a provisional version only. Copying images from a card 1 Usually, you will copy images from a card by connecting the camera to a computer and using FlexColor. However, you might also want to load images from a card to a portable FireWire hard disk or ImageBank-CF, allowing you to erase the card and keep shooting even when you do not have a computer with you. You cannot copy images to a card.
This manual is a provisional version only. Creating batches 1 Batches help you to organize your work. They are very similar to folders on a computer hard disk. Use the Batch command of the STORAGE menu each time you want to create a new batch. For more information about batches, please see Working with Media and Batches . To create a new batch: 1. Select MAIN MENU > STORAGE > BATCH. (See also Navigating the Menu System for details about how to find this setting.) 2.
This manual is a provisional version only. To change the default status assigned to each new image: 1. Select the MAIN MENU > STORAGE > Default Appr. level entry. The current setting is shown here. (See also Navigating the Menu System for details about how to find this setting.) 2. Use the (+) and (-) buttons to step through the available settings until the default status you wish to use (auto, green or yellow) is shown. 3.
This manual is a provisional version only. Navigating the display settings MAIN MENU > SETTINGS > Miscellaneous The MISCELLANEOUS menu contains a few settings that did not fit under any of the other menus. 1 Selecting an interface The interface setting controls the way the camera will appear to you computer when you connect it. You have the following choices: • Camera: The camera will present itself to your computer as a camera.
This manual is a provisional version only. The About box 1 Occasionally, Hasselblad may release updates to the internal software of the sensor unit (this is called “firmware”). These updates may fix small errors and/or add new features. You will probably receive additional assistance from Hasselblad technical support if and when a new update is available. In this case, it may be important to know the serial number and current firmware revision of your sensor unit. To find this out: 1.
This manual is a provisional version only. Menu Shortcuts To help you work faster, the sensor unit provides shortcuts to some of the most commonly used menu commands that do not otherwise have a dedicated button on the front panel. These are accessible by pressing and holding one of the front-panel buttons for a second or so. These are mentioned where appropriate elsewhere in this manual, but we summarize them here for your convenience.
This manual is a provisional version only. Care and Maintenance Handling and Storage • Always replace the protective CCD/filter cover when the sensor unit is not mounted on your camera. • Do not touch the exposed CCD/filter with your fingers. • Keep all foreign objects out of the CCD opening. • Store your sensor unit away from moisture and excessive heat. Please see “Technical Specifications” for complete operational and storage requirements. • Protect your sensor unit from impact—do not drop it.
This manual is a provisional version only. 4. Finally check if the IR filter has been properly cleaned either by visual inspection or by mounting the sensor unit to the camera and making a shot. If further cleaning is needed, repeat cleaning procedure. Cleaning with an E-Wipe E-wipes are individually packed wet tissues. 1. Tear at the notch to break seal. 2. Remove e-wipe from its packaging and continue without delay. 3. Fold the tissue to match the width of the IR filter. 4.
This manual is a provisional version only.
This manual is a provisional version only. 8 Light Metering & Exposure Control ■ Three metering methods ■ Five exposure methods ■ Extremely accurate light metering The light metering system is capable of selective sensitivity producing three reflective metering methods: Average, Centre weighted and Spot. All methods are measured in increments of 1/12 EV. Information transfer is rapid and automatic ensuring consistently correct exposure settings even in difficult and changeable lighting situations.
This manual is a provisional version only. Light metering and exposure control Two primary factors have to be considered when making exposure control choice, namely, metering method and exposure method: Metering method determines in which manner the light measurement is made and how much of the image is taken into account( Average, Centre Weighted and Spot). Exposure method involves the parameters and deciding factors about how the light measurement is translated into aperture and shutter speeds.
This manual is a provisional version only. 1 Selecting metering method 2 Proceed as follows with the camera in active mode: 1. Press the EXP button on the viewfinder. 2. Turn the rear control wheel (in either direction 2a) to successively access the three choices: Average, Centre Weighted, and Spot 2b. 3. Press Save (DRIVE button) to retain the setting. EXP � 3 Exposure method Exposure can be controlled either manually or by using one of four automatic modes.
This manual is a provisional version only. A ‘+ 0.3’ above the scale in the display, as in illustration 4 for example, would indicate a ‘0.3 EV overexposure’ setting. Conversely, a ‘-2’ , for example, would indicate a ‘2EV underexposure’ setting. Note that the appearance of a +/- symbol on the grip and viewfinder LCDs in manual mode means that a change has been made to the exposure compensation setting. See later section on ‘Exposure compensation’.
This manual is a provisional version only. AE- L button 1 1, 2 This button has two main functions that can be incorporated in various working methods involving exposure locking. It also has an extra function for the flash meter capability (see AE-L section under Flash). The AE-L button can: 2 a) lock an EV setting in manual and automatic modes. b) be used as a brightness range checking facility in standard terminology or Zone System terminology.
This manual is a provisional version only. Alternatively, you can also pre-set the initial zone reading in order to save time and effort where there is no freely available ‘zone 5’ subject for light measuring. For example, you might be on a sandy beach where you know that sand is normally classified as zone 6. You can pre-programme the zone placement by holding down the AE-L button while choosing the new zone value and turning the front control wheel until zone 6 appears.
This manual is a provisional version only. 9 General Functions ■ Manual and autofocus modes ■ Two drive modes ■ Quick adjust wheel ■ Profiles This section describes the basic and general functions used in most situations. By understanding the capabilities of the H system you will be able to gain a great deal of control of how you work in the future. By taking advantage of the many features available, you might well find your normal practices changing for the better.
This manual is a provisional version only. Power The camera can be set at two active power modes − ON or Standby − as well as OFF. In active modes, battery consumption is least in Standby mode and most in ON mode. The camera enters Standby mode automatically after 10 seconds (default) to preserve battery consumption but this interval can be changed in Custom Options. Also, after 10 seconds, the display on the OLED on the sensor unit is dimmed and after 30 seconds the display is turned off completely.
This manual is a provisional version only. Manual focus mode 1 The Manual focus mode is set by the front control wheel on the grip in the following manner: In camera active mode: 1) Press the AF button on the grip. 2) Turn the front control wheel to: Manual 3) Press Save to store the setting. AF You can also use the shutter release button ‘half-press’ function to save a new setting and automatically return to the main screen.
This manual is a provisional version only. Continuous At Continuous setting (AF C), the shutter can be released rapidly before the lens is focused in order to capture a split-second shot (in Single Shot, an exposure cannot be made until the camera has had time to focus). However, the camera will continue to focus if a moving subject is within the focusing zone or if you recompose, even though the shutter release button is half pressed.
This manual is a provisional version only. Drive There are two drive modes, Single and Continuous, accessed by pressing the DRIVE button on the grip. Single In Single mode, an exposure is made when the shutter release button is pressed and the camera is made ready for the next exposure. To make the next exposure however, you must first release the shutter release button and then press again. In camera active mode: 1) Press the DRIVE button on the grip.
This manual is a provisional version only. 1 Profiles 2 The profiles feature allows rapid access to pre-determined combinations of settings that increase the speed and security of workflow. One example might be in a social situation where there might be a need for formal outdoor portraiture followed by informal indoor handheld flash-assisted wide-angle shots, both situations requiring very different settings in a stressful environment.
This manual is a provisional version only. you want and then press the Load (AF) button. All the saved settings will then be automatically implemented. If you decided to change the settings but nevertheless keep the Profile name on the list, the new set of parameters will be retained under that name. That is to say, the settings will not be the same as listed here, despite the name. It might be safer practice to always change the profile name to avoid later confusion.
This manual is a provisional version only. 10 Advanced Features ■ Programmable self timer ■ Programmable bracketing ■ Programmable interval setting ■ 24 custom options ■ Data and text imprinting This section describes the features that might not need to be accessed everyday but should be exploited wisely to obtain the optimum from the system. Some features are a little more special, bracketing for example.
This manual is a provisional version only.
This manual is a provisional version only. There are a number of more advanced features that while not necessarily used every day still remain immediately accessible through the menu system. They provide the integral finesses that make the H2D a powerful and sophisticated tool to satisfy a variety of professional demands. There are four main functions: 1. Self timer 2. Bracketing 3. Interval timer 4. Settings 5.
This manual is a provisional version only. 1 Self timer setting 2 The Self timer function is set in the following manner: � ���� 1) Press the MENU button on the grip. 2) Turn the front control wheel until Self Timer appears. 3) Press ENTER (DRIVE button) on the grip.
This manual is a provisional version only. Bracketing options available 2 frames or 3 frames or 5 frames options available options available 1/3 EV or 1/2 EV or 1 EV 2 Bracketing The bracketing facility provides an automatic series of exposures; one at the standard exposure setting (Manual or Auto) and the others with pre-determined deviations in EV from the standard exposure. This is particularly useful for images containing a very wide tonal range, for example.
This manual is a provisional version only. 1 Bracketing setting 2 � The Bracketing function is set in the following manner: 1) 2) 3) 4) ���� Press the MENU button.
This manual is a provisional version only. Interval options available 2 frames − 255 frames options available 1 second − 1 hour 1 3 2 Interval By using the interval setting, you can allow the camera to take a series of exposures automatically over a set period. This is often required for time and motion studies, security surveillance, nature study, etc. The exposure and focus settings (Manual or Auto) will be according to the camera settings at the time of exposure.
This manual is a provisional version only. Settings / Custom Options options available CUSTOM OPTIONS 1 4 2 � From the Settings screen you can access three main sub-settings: Custom options, Image Info and System status by turning the front control wheel. From each of these three sub-settings you can access further screens. Custom options has more than 24 screens, Image info has two more screens each with more choices and System status has two more screens.
This manual is a provisional version only. Standby timeout 1 • 5s • 10s • 15s • 30s Determines the amount of time the camera remains active before it automatically reverts to standby mode (indicated on the grip LCD by the H2D logo). Minimises battery consumption. EV increment 2 • 1 Step • 1/2 Step • 1/3 Step image • Dig. foc.
This manual is a provisional version only. Spot mode 12 • Normal • Zone Determines how the camera behaves when set to Spot Mode. All controls locks control wheels and buttons. Wheels locks only control wheels. They remain operable in any setting mode, however. Off disables lock function. Normal makes the camera behave in the same fashion as when set to Average or Centre Weighted. Zone makes the camera behave in the same fashion as the Hasselblad 205FCC.
This manual is a provisional version only. Show ISO 22 • Yes • No Allows the display of ISO settings on the grip LCD Yes enables the display. No disables the display. Bracket param. in Manual 23 • Shutter speed • Aperture Selects either the shutter speed or the aperture as the parameter which changes in a bracketing sequence when in Manual exposure mode. Shutter speed selects changes in shutter speed. Aperture selects changes in aperture settings.
This manual is a provisional version only. Customizable button function list Histogram The USER, AE-L, STOP DOWN and M.UP buttons can all be reassigned to different functions. The USER button has no function until specifically assigned one (default is ‘None’). The AE-L, STOP DOWN and M.UP buttons, however, by default are assigned the function appropriate to the name, until assigned otherwise. Recalls the last shown histogram. Grey balance exp. Initiates a grey balance exposure.
This manual is a provisional version only. Image info 1 4.2.2 2 � ���� Image info In Image info you can compose your own combination of letters, words, symbols, etc to be included in the metadata. The same procedure is also used to change a Profile name. Text setting / Profile name changing 4 3 ����� � ����� 5 6 ����� ����� 1 AF ����� ���� Sel. Press the MENU button on the grip. Turn the front control wheel until Settings appears. Press the Enter (DRIVE) button on the grip.
This manual is a provisional version only. 2) Find the character you want by scrolling with the rear control wheel until it appears on the screen. (The ‘space’ character is the ‘empty space’ to the left of the exclamation mark, top row furthest to the left). 3) Move the selector cursor with a combination of the front and rear control wheels until the desired character is highlighted. 3 2 � � � 4 5 AF ����� ����� ���� Sel. ���� 4) Press the Sel.
This manual is a provisional version only. System Status 4.4 System Status 2 1 � ���� Check component usage for servicing reasons as follows: 1) Press the MENU button on the grip. 2) Turn the front control wheel until Settings appears. 4 3 ����� � ����� 5 4) Turn the front control wheel to access Info. 6 ����� ����� 7 ����� 3) Press the DRIVE (Enter) button on the grip. 5) Press the Enter (DRIVE) button � 6) Press the Enter (DRIVE) button.
This manual is a provisional version only. 11 Flash ■ Sync at all shutter speeds to 1/800s ■ Integral fill-flash ■ SCA 3002 compatible ■ Flash measure capability ■ Rear sync capability The H system meets professional demands for a variety of situations where flash is required. It includes an integral flash primarily intended for fill-flash use but strong enough for simple close work.
This manual is a provisional version only. The H2D can be used together with most flash units in manual mode. However, to make use of a TTL automatic function, you must ensure the flash unit is compatible with the SCA 3002 system. Connection is either by the PC socket or by the hot shoe (see warning note below). The viewfinder houses an integral fill-flash with a guide number of 12 and features OTF/TTL flash control.
This manual is a provisional version only. 2 1 FLASH ���� � 3 3) Turn the rear control wheel to set: • normal sync (flash triggered just after the shutter opens) • rear sync (flash triggered just before the shutter closes) • flash measure (with non-TTL flash units or TTL units in Manual mode) 4) The grip LCD shows the flash mode - Normal or Rear - in the standard display. 5) When set to Flash Measure, a specific screen requests you to press the AE-L button in order to make a reading. See below for details.
This manual is a provisional version only. Separate flash unit connection and use Separate flash units can be electrically connected either by way of the hot shoe accessory holder (see previous warnings) on the top of the viewfinder or via a cord to the PC connection port on the left hand side of the camera body. Slave unit switches/ transmitters can also be connected similarly dependant on unit (see specific user manuals for details). Keep the plastic safety cover in place in the hot shoe when not in use.
This manual is a provisional version only. 12 Optional Accessories ■ Converter ■ Extension tubes ■ Release cord ■ Filters ■ Tripod quick coupling ■ Support strap ■ Grid focusing screen ■ CF adapter ■ Proshade Optional accessories provide the opportunity to extend the capabilities of your system or just to add extra convenience to suit your way of working.
This manual is a provisional version only. There are a number of optional accessories available for the H2D with more being developed to suit a variety of photographic situations and needs. Please see www. hasselblad.com for the latest information. The figures in brackets after the headings are the product codes. Converter H 1.7X Camera strap H (3053616) Extra wide camera strap with anti-slip backing.
This manual is a provisional version only. 13 Appendix ■ Glossary of Terms ■ P and Pv explanatory charts ■ Technical specifications ■ Equipment Care, Service & Guarantee This section provides an insight into the more technical aspects of the H system as well as some important reference information.
This manual is a provisional version only. Glossary of Terms LED For the sake of clarity, here are short and simple explanations of several terms, items and features mentioned in the manual that may be unfamiliar to some. Bracketing The practice of making extra exposures over or under (normally both) the ‘standard’ exposure to ensure the desired result. This is particularly useful in difficult, wide-ranging lighting conditions. Easily set and controlled with the H2D.
This manual is a provisional version only. the bracketing option too. All these parameters can be preset and stored as a profile that is rapidly accessible. Quick save When altering settings, a half-press of the shutter release button will cause a return to the main screen and save the new setting at the same time.
This manual is a provisional version only. True exposure Shutter position T3 = T1 Open Exposure at max aperture (e.g. f/2,8) Exposure at aperture f/4 Exposure at aperture f/4 adjusted with true exposure Closed T1 T2 Time True exposure The effective shutter speed for a central lens shutter is defined as the length of time between the opening and closing when measured at the half height position when expressed in diagram form (see diagram).
This manual is a provisional version only. Automatic exposure — P & Pv Mode P Mode -5 -4 50 50-110 @ 50 35 50 50-110 @ 50 80 120 50-110 @ 110 80 120 50-110 @ 110 210 150 210 150 -3 -2 -1 1 0 2 3 4 5 6 7 8 9 10 1.4 Aperture A perture 17 11 18 16 19 22 20 32 21 45 22 64 23 32s 16s 8s 4s 2s 1s 2 4 8 15 30 60 125 250 500 1000 -1 1 0 2 3 4 5 6 7 8 9 10 13 14 15 16 8 17 11 18 16 19 22 20 32 21 45 22 64 90 64s 11 12 5.
This manual is a provisional version only. Technical specifications Camera Type Auto-focus, auto-exposure digital SLR camera with interchangeable viewfinders and lenses. Construction One piece stainless steel shell. Die-cast aluminium internal structure. Tripod sockets (1/4 and 3/8”) and quick coupling tripod plate for rapid mounting. Lenses Hasselblad HC lenses with built-in electronically controlled shutter and aperture. Automatic or manual focusing with instant manual focus override.
This manual is a provisional version only. User interface Both basic and advanced functions are set using buttons and control wheels on the camera body in conjunction with the grip and viewfinder graphic interface LED’s. Sensor unit menu visible and controllable from unit’s OLED and from FlexColor on a tethered computer. Battery grip rechargeable 7.2 V Li-ion type. 7.2 V / 1850 mAh output. Battery charger Li-ion 7.2 VDC Uses DV charge termination technique to prevent over-charging.
This manual is a provisional version only.
This manual is a provisional version only. BODY Default setting (Standard Profile) Exp.mode LM mode Exp. adjust Focus mode Drive mode Flash sync Flash adjust Self timer Bracketing Interval timer Custom options Imprint SENSOR UNIT A (Aperture priority) Centre weighted 0 AF-S S Normal (beginning of exp.
This manual is a provisional version only. SERVICE Problems, Equipment Care, Service & Guarantee The H2D is a very sophisticated camera that relies on much information being passed and processed to and from each modular unit to produce the correct behaviour. It is therefore essential that reasonable care is taken in attaching, detaching and storing the viewfinder, lenses, extension tubes, etc to ensure that the databus connections are not damaged or soiled in any way.
This manual is a provisional version only. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Victor Hasselblad AB & Hasselblad A/S. Victor Hasselblad AB & Hasselblad A/S assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
This manual is a provisional version only.
