Repair Guide, Diagrams and Assembling Charts
Table Of Contents
- Service Manual 203FE - 205FCC - 205TCC Cover
- Content list
- Related Service Infos
- 1. General description
- 2. Specifications
- 3. Checks & Adjustments
- 4. Tools
- 5-22 Exploded Views and Spare Part lists
- 5. Shell
- 6. Control panel, mechanics
- 7. Control panel, electronics
- 8: Display flex and main circit board
- 9. Contact flex and transport mechanism plate
- 10. Transport mechanism plate
- 11. Front bayonet plate
- 12. Curtains and rear plate
- 13. Mirror assembly
- 14. Display prism and fucusing screen
- 15. Chassis
- 16. Reflection protectors
- 17. Bottom mechanism plate, mechanics
- 18. Bottom mechanism plate, brakes
- 19. Bottom mechanism plate, electonics
- 20. Spring housing
- 21. Winding crank
- 22. Winding crank - modified from May 1997
Camera body 203FE - 205FCC - 205TCC
containing the PRS. Untighten the two screws (Pos. No. 12, page 9) and carefully
change the position of the flex in the direction required. Tighten the screws and
recheck.
7:2 PANEL. Check the control panel functions.
7:3 SPEED RING. Make sure all speed ring settings are indicating correctly.
7:4 DISPLAY. Check the display indications. Note! To get the flash indicator to light up,
the sync cable must be connected.
7:5 CURRENT. Check the consumption (max. 10 mA at 5.6 volt) and the drain (max.
20 uA at 5.6 volt).
7:6 LENS. Check the communication between a lens and the camera body. (F-stops)
7:7 MAGAZINE. Check the communication between a magazine and the camera body.
7:8 SHUTTER. Start by adjusting the travel times. Use 1/2000 sec. and adjust the spring
housing until both curtains have a speed between 9.5 - 9.7 ms. (0 ± 0.07 ms).
At this point, also make a final adjustment of the braking mechanism if necessary.
The brake is checked as follows: Release the camera. Rotate the 2nd shutter gear
(Pos No. 25, page 17) and count the number of times the catch (Pos No. 4, page 18)
and the brake plate (Pos No. 3, page 18) engage. (Min. 4 times). For an adjustment
use the nut driver 903755 or 903474. (See page 3:4).
Check/adjust the speed 1/2000 sec. Use the "shutter speed" potentiometer for
an adjustment. (See page 3:4). Max. deviation ± 0.3 EV.
Check the speed 1/1000 sec. Max. deviation ± 0.3 EV.
7:9 LIGHT METER. Check/adjust the light meter. Use the "light meter" potentiometer
for an adjustment. (See page 3:4). Max deviation ± 0.3 EV. Do not use any
other light output except EV 15, since the camera is not built in to the shell.
7:10 FLASH SYNC. Check/adjust the flash sync. The delay is adjusted to 0 - 0.20 ms by
altering the position of the first sync contact. (See page 3:4).
7:11 FLASH METERING. Check/adjust the flash meter. Use the "flash meter"
potentiometer for an adjustment. (See page 3:4). Max. deviation ± 0.3 EV. Use the
setting ISO 100 and light output EV 15.
7:12 C-POSITION. Check/adjust the C-position. It is adjusted by extending/shortening
the release arm 103389. (See page 3:4).
Checks & Adjustments 3:2
June 1998
Revision 1