Operation Manual
I 6, 20,
30, 40, 50,
60 seconds.
The
standard
setting is I
0
seconds.
pr3
,,,r,,1.,,
;:,,:.:
To
adjust the automatic
flash
metering
function,
facilitat-
ing
the use of fill-in
flash.
The setting
range is-3
to + I EV
in
l/:
EV
increments.
The
standard
setting is
0.
How
to u.1.e the "Pr"
Mode
The programming
Pl mode
can
be selected
at any time
to change
the standard
values
for film
sensitivity,
flash,etc,
or
to change previously
made
settings. The
changed
values
are effective
as soon
as they are
entered.
By repeatedly
pressing
the AE-lock
button you
can shift
through
the
Pl-functions
in
the sequence Pr'l-->Pr2--
>Pr3-->
Pr1--)etc.
The
sequence
always starts
on the
last
used function
except
after
a battery
change. ln Pr
mode
the camera
can
be started
by depressing
either the
exposure release
button
to the pressure
point
or the AE-
lock
button.
Setting the film
speed
::.::::::::::::::::.:::::::::j::::::::::::::r::::::::::.:::
(Prl
function)
'.80,.*.'8e..,.....
Setting
the film speed
in Pr mode
is possible
only
when
an A-magazine
is used. This
is indicated
on the display
by the
symbol
"Pr"
before the film
speed
value. With
an
E-magazine
the film
speed is
set on the magazine
dial,
the Prl
function is
inactive
and
the display
shows the
magazine
dial setting
only.
l.
Set the mode
selector
dial in
the
Pr position.
2. Depress
the AE-lock
button
to start
the camera
and
then repeatedly
if required
to
select the Prl function.
3, Press
the
adjustment
buttons to
change the film
speed
value. The
upper
button increases
and the lower
de-
creases
the value
in steps
of
1/r
EV
4. Reset
the Mode
Selector Dial
to the desired
exposure
mode
or
press
theAE-lock
button
to switch
to next Pr-
function.
7x
Afilm
speed value
manually
inserted
in
/
:
\ the
Prl
function
is
stored untilchanged
again
by
the same
procedure
(or
until
the battery is removed).
If an E-
(or
TCC-) magazine
is
attached
the film speed
set on
the magazine
dial overrides
the
stored value. When
the
magazine
is
detached
the stored
value is automatical-
ly recalled.
Thus
it is easy
to shift
between E-magazines
and A-magazines
with films
of different
speeds
(e.g.
Polaroid
films).
Setting
the
selftimer
delay
(Pr2
function)
l.
Set the mode
selector
dial
in
the Pr position.
2. Depress
the AE-lock
button
to start
the camera
and
then repeatedly
ifrequired
to select
the
Pr2
function.
3. Press
the adjustment
buttons
to change
the selftimer
delay. The
upper button increases
the delay
and the
Iower
button
decreases it
with
the
predetermined
steps.
4.
Reset
the
mode
selector dial
to the desired
exposure
mode
or
press
the
AE-lock
button to
switch to next Pr-
function.
Adjusting
the automatic
flash
meteri ng
(Pr3
fu nction)
The function
is
used
to
introduce
a
fixed
adjustment
in
the
automatic flash
control
to
reduce
or
increase
the flash
power,
e.g.
for
fill-in flash
applications.