Installation Manual Model 664 Automatic Preservative Applicator 664-14-INST 5/22
(intentionally blank) 2
Harvest Tec Model 664 Installation Table of Contents Introduction System Requirements Tools Needed Installation of Controls and Harnesses 1. Installation of Dual Channel Processor (DCP) DCP or PIP Location for AGCO and CNH Balers 2.
Introduction Thank you for purchasing a Harvest Tec Model 664 Hay Preservative Applicator. This 664 applicator system has been designed to be operated through an Apple iPad (not included) using the Hay App. As well as the option to plug directly into most tractors that have an ISOBUS Monitor. The 664 Applicator System offers these advantages by operating through an Apple iPad: 1. 2. 3. 4.
1. Installation of Dual Channel Processor (DCP) The Dual Channel Processor (DCP) has the same bolt pattern as the Precision Information Processor (PIP) you will be removing. The location of the main controller does not change so use the same holes and install the new Dual Channel Processor (DCP) in the same location with two 5/16” x 1” bolts, two 5/16” x 1-1/4” bolts, locks, fender washers and hex nuts.
2. Installation of Main Power / Communication Harness Route cords 006-6650LS2 along this path or similar inside of the baler. Keep cords away from moving parts and hydraulic hoses. Secure with existing cable clamps or use cable ties. When all connections are made to DCP secure wires. Connecting the optional ISOBUS plug to the tractor Attach the optional ISOBUS connector (006-6670A) to the end of the communication harness (006-6650TM).
Installation of iPad Integration Control Locate a safe location in the cab of the tractor to place the iPad Integration Control (030-6672C). Recommended location is securely fastened out of the operators way in a location that is close enough to reach with the iPad cord. Connect the Power / Communication harness (006-6650TM(E)) to the bottom of the receiver.
Wiring Diagram 1. The Baler Power/Communication Harness (006-6650LS2) will attach to the open port of the Tractor Harness (006-6650TM) and run back to the Dual Channel Processor (006-6671LS). Connect the large plug of the Baler Power/Communication Harness (006-6650LS) to the bottom (shorter side) of the DCP. 2. Install green terminator (006-5650Z) to the port labeled Modular Port on the Pump Controller (006-5672). 3.
Pin Outs Power/Comm Harness 006-6650TM at Hitch Pin 1 Red +12V Power to TSD Pin 2 Red +12V Power to DCP Pin 3 Orange Keyed Power Pin 4 Gray Shield Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Orange Can1 Hi Pin 8 Black Ground from TSD Pin 9 Black Ground from DCP Pin 10 Blue Can1 Low Power/Comm Harness 006-6650LS2 at Hitch Pin 1 Red +12V Power to TSD Pin 2 Red +12V Power to DCP Pin 3 Orange Keyed Power Pin 4 Gray Shield Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Orange Can1 Hi Pin 8 Black Gro
Pin Outs (continued) Main Power Connector on DCP Pin 1 Red +12V Power from tractor Pin 2 Black Ground from tractor Pin 3 Orange Keyed power Star Wheel and Bale Rate Sensor connector on DCP Pin 1 Blue +12V Power Pin 2 Orange Ground Pin 3 Black Signal for sensor 1 Pin 4 White Signal for sensor 2 Pin 5 N/A Pin 6 N/A Pin 7 N/A Pin 8 Violet Star wheel input 1 Pin 9 Brown Star wheel input 2 End of Bale sensor on DCP Pin 1 Brown Sensor Power Pin 2 Blue Sensor Ground Pin 3 N/A Pin 4 Black Signal from Sensor Pump
Parts Breakdown (Converting a 500 Series to a 600 Series) 6 1 2 3 4 5 Ref 1 2 3 4 5 6 7 NP NP Description Key Switch Wire-orange DCP Main Control LS 600 Auto Terminating Resistor 500 Series-green Dust Plug (only one included)-yellow DCP Baler Harness 30 ft DCP Tractor Harness iPad Integration Control Optional ISOBUS Adapter Plug (not included) USB Cord 7 11 Part Number 006-5650K 001-6671LS2 006-5650Z 006-5651Plugs 006-6650LS2 006-6650TM 030-6672C 006-6670A 006-6672USBC Qty 1 1 1 1 1 1 1 1 1
Notes 12
Notes 13
Notes 14
Harvest Tec LLC. Warranty and Liability Agreement Harvest Tec, LLC. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, LLC. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, LLC.
HARVEST TEC, INC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.
