Installation Manual Model 347U 25 Gallon Automatic Preservative Applicator 347U-17-INST-Imp&Metric 5/22 1
DECLARATION OF INCORPORATION MANUFACTURER: Harvest Tec LLC. 2821 Harvey St. P.O. Box 63 Hudson, WI 54016, U.S.A. REPRESENTATIVE ESTABLISHED IN COMMUNITY: Profitable Farming Company Middle Barlington, Roborough Winkleigh, Devon, EX19 8AG ENGLAND The person above certifies and declares that: VIRTUAL MACHINE: Equipment mounted on a farm press and for the application of innoculants onto forage crops.
Harvest Tec 347U Table of Contents Page 3 3 4-7 4 5 5 5 6 7 8 8 8 9 10-11 12-19 12 12 13 14 14 15 15 16 17 18 19 21-22 23 Introduction Tools needed Installation of applicator Installation of Tank, Mounting Brackets & Drain / Fill line Mounting Control Box Installation of Nozzle Holders Installation of Plumbing Installation of Moisture Sensing Pads Installation of Bale Sensor Installation of iPad Integration Control iPad Integration Control Light Signals Bluetooth Receiver Lights Wiring Diagram Pin Outs Par
Installation of Applicator Installation of Tank, Mounting Brackets, and Drain / Fill Line Locate the tank base bracket (001-4442U). This bracket will mount on the front of the baler is show below. Depending on the year of the baler only two of the required three holes may be premade on the baler. Mark and drill two 1/2” (13mm) holes (one per side) if necessary. Be sure to check behind the area before drilling to ensure there is nothing that will be damaged.
Mounting Control Box Locate the controls package. Position the control box (006-3671RB) as shown on right. If the mounting holes are not pre-drilled on the tank saddle (001-4442), drill four 1/4" (7mm) holes. Using the supplied 10/32 x 3/4” Phillips flathead machine screws, nylock washers and nuts to mount the control box. Placement of Nozzle Holders Install Kit 347U The cross bar on the wind guard above the pick-up head provides a mounting point for the nozzle holders (001-4714J).
Installation of Moisture Sensor Pads Figure 1 2” from back of chamber (51mm) 1” from top of roll (25mm) 1. If your baler is equipped with bale shaping pads, remove disc and use existing hole (may need to be drilled larger, 3/4" (19mm) to install new moisture sensing discs. 2. If your baler is not equipped with bale shaping pads you will need to drill a hole in the chamber directly behind and above the starting roll (Figure 1). 3. The mounting hole will be 3/4" (19mm) in diameter.
Installation of Bale Sensor The bale rate timer sensor is used to determine when the baler door is open. With this information the system is able to change the tons/hour automatically (see Operating Instructions, Automatic Mode). Locate the sensor (006-7400) and the sensor bracket (001-4648RB). On the right side of the baler find a location 1”– 6” down from the hinge to mount the bracket. Check for clearance with hydraulic cylinders before mounting the bracket.
Installation of iPad Integration Control Locate a safe location in the cab of the tractor to place the iPad Integration Control (030-6672C). Recommended location is securely fastened out of the operators way in a location that is close enough to reach with the iPad cord. Connect the Power / Communication harness (006-6650TM(E)) to the bottom of the receiver.
Wiring Diagram 1. Connect the power harness (006-3650T) to the tractor battery (12 volt) using the red wire with fuse to the positive side and the black wire to the negative. a. The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty. CONTACT HARVEST TEC BEFORE MODIFICATIONS. b. This unit will not function on positive ground tractors. c.
Pin Outs Power Harness 006-3650T at Tractor Hitch Pin 1 Red +12V Power to BLE Pin 2 Red +12V Power to THS Pin 3 Orange Keyed Power Pin 4 Not Used Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Not Used Pin 8 Black Ground from BLE Pin 9 Black Ground from THS Pin 10 Not Used Power Harness 006-3650B1 at Baler Hitch Pin 1 Red +12V Power to BLE Pin 2 Red +12V Power to THS Pin 3 Orange Keyed Power Pin 4 Not Used Pin 5 Green HT Can Low Pin 6 Yellow HT Can Hi Pin 7 Not Used Pin 8 Black Ground from BLE Pin 9 B
Pin Outs (continued) End of Row Sensor at 300 Controller Harness Pin 1 Red/White +12V Power Pin 2 Black/White Ground Pin 3 Yellow Signal Pin 4 N/A Moisture Sensor connection at 300 Controller Harness Pin 1 Not Used Pin 2 Not Used Pin 3 Not Used Pin 4 Not Used Pin 5 Not Used Pin 6 Not Used Pin 7 Not Used Pin 8 Blue Signal for Sensor 1 Pin 9 Blue Signal for Sensor 2 Pin 1 Pump connection at 300 Controller Harness Pin 1 Red Power to Pump Pin 2 Black Ground to Pump Pin 2 Solenoid Connection at 300 Controll
Model 347U Base Kit 5 3 1 2 4 6 Ref 1 2 3 4 Description 25 Gallon tank 25 Gallon saddle Strap Tank fitting Part # Qty 005-9022 1 001-4442 1 001-4402 2 005-9100 2 Ref Description 5 Tank lid Tank lid gasket 6 Tank mounting bracket Tank Saddle Kit Part # 005-9022C 005-9022CG 001-4442U Qty 1 1 1 030-044225-TK (1-5) Moisture Sensors 1 2 3 6 5 Ref 1 2 3 Description Plastic Pad Moisture Disc Plastic Bushing Part # Qty 006-4641F 2 006-4641H 2 006-4641G 2 Ref 4 5 6 Description Plastic Isolator 1/2X4 1/
Parts Breakdown for Pump Assembly Part# 003-EL3812 007-4120DE 003-M3838 003-SE38 002-4566F 003-RB3814PB 006-4729A 003-RB1214PB 003-M1212F Description 3/8”MPT X 1/2"HB Elbow 300 Series Pump 3/8” x 3/8” Union 3/8” Street Elbow 3/8” Check Valve RB 3/8” x 1/4” Reducer Flow Meter – Block Style RB 1/2" x 1/4" Reducer 1/2" Coupler Qty 1 1 1 1 1 1 1 1 1 Part# Description 003-M1212 002-4315-100 003-SE12 002-2212 003-EL1212 001-4648XL 001-4648X 003-A1212 003-A3812 1/2" Union 1/2" Line Strainer-100 Mesh 1/2" S
Control Box and Wiring Harnesses 3 2 1 4 6 5 Ref 1 2 3 4 5 6 NP Description Tractor Power Harness iPad Integration Control Baler Power Harness (20’) Control Box Dust Plug Kit Key Switch Harness USB Cable Part # 006-3650T 030-6672C 006-3650B1 006-3671RB 006-5651Plug 006-5650K 006-6672USBC Complete Assembly 030-363CPA End of Bale Sensor Kit A 1 2 3 Ref 1 2 3 Description End of Bale Sensor EOB Extension End of Bale Bracket Part # 006-7400 006-7400EXT 001-4648RB Complete Assembly EOB-RB-A 14
300 Solenoid Package 1 2 3 4 5 7 10 8 6 9 Solenoid Package A (Applicator Kit: 351) Ref 1 2 3 4 5 Description Solenoid Harness (5’) #6 Hose Clamp 1/4" x 1/2" Straight Fittng 1/4" Female Connector Rubber Washer Part # 006-3650-S1 003-9003 003-A1412 004-1207G 004-1207W Qty 1 1 1 1 2 Ref 6 7 8 9 10 Description 1/4" Female Disconnect Solenoid Solenoid Valve Body 1/4" x 1/4" Straight Fitting Mini Hose Clamp Part # 004-1207H 002-2203F 004-1207VF 003-A1414 003-9002 Complete Assembly SOL-3SP-A Ho
Parts Bag Packages PBA-1 1 PBP-16 5 10 12 8 2 6 9 11 13 3 7 4 Ref 1 2 3 4 5 6 7 8 9 Description 3/4" Ball Valve Valve Holder Female Coupler Male Shut-Off Plug 3/4” x 3/4" Elbow #10 Hose Clamp 3/4" x 3/4" Straight Fitting Valve Decal Chemical Hazard Decal Part # 002-2200 001-6702H 002-2204A 002-2205G 003-EL3434 003-9004 003-A3434 Complete Drain Fill Kit 030-0493DFK DCL-8004 DCL-8001 Qty 1 1 1 1 1 2 1 1 1 16 Ref 10 11 12 13 Description 3/4" x 1/2" Elbow 3/4" Jiffy Clip #6 Hose Clamp Small
Optional iPad Mini Mounting Kit (030-2014MK) 2 1 3 4 5 7 8 6 Ref 1 2 3 4 5 6 7 8 NP Description Suction cup mount Ram mount iPad Mini® spring load cradle (Mini 4) 16 gauge power wire Female spade connector Eye loop connector iPad Mini Charger 12V iPad Mini 4 case 4 amp fuse Part # 001-2012SCM 001-2012H 001-2012SLC 006-4723P Hardware Hardware 001-2012P 001-2012C4 Hardware Mounting Kit Assembly 030-2014MK (Includes All Parts) Qty 1 1 1 1 2 2 1 1 1 Installation Instructions 1.
Optional iPad Display Kit (030-4670DK) 9 1 2 3 4 5 6 Ref 1 2 3 4 5 6 Description Suction cup mount Ram mount iPad Mini spring load cradle (Mini 4) 16 gauge power wire Female spade connector Eye loop connector 7 8 Part # 001-2012SCM 001-2012H Qty 1 1 Ref Description Part # 7 iPad Mini Charger 12V 001-2012P 8 iPad Mini 4 case 001-2012C4 001-2012SLC 1 9 iPad Mini 4 006-4670IP 1 006-4723P Hardware Hardware 1 2 2 NP 4 amp fuse Hardware 1 Mounting Kit Assembly Qty 1 1 030-4670DK (Includes
347U Installation Kit (Shield Only) 2 3 5 4 6 1 7 8 9 13 10 12 14 Ref 1 2 3 4 5 6 7 8 9 10 Description U bolt Hose clamp 1/4"MPT x 1/4" HB 1/4" SqTee 1/4" Female St Elbow Oetiker Clamp Nozzle Holder Hose 1/4" x 1/4" Fitting Tip Strainer Part # Qty 001-4714UBS 4 003-9002 4 003-A1414 5 003-TT14SQ 1 003-SE14F 1 003-9008 4 001-4714J 2 002-9016 3 ft 003-A1414F 2 004-1203-100 2 Ref 11 12 13 14 NP Description Tip – White Tip – Red Nozzle Body Nozzle Cap 477 Jiffy Clip 11 Part # Qty 004-XR11008VS 2 00
Notes 20
Notes 21
Notes 22
Harvest Tec LLC Warranty and Liability Agreement Harvest Tec, LLC. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, LLC. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, LLC.
HARVEST TEC, LLC. P.O. BOX 63 2821 HARVEY STREET HUDSON, WI 54016 PHONE: 715-386-9100 1-800-635-7468 FAX: 715-381-1792 Email: info@harvesttec.
