Monitor Installation 50" Speaker (Optional) Installion • Match red to red, black to black of Speaker / TV. • Always lift the monitor itself (not the speakers) when handling or moving the monitor after speakers have been installed. Assemble the monitor to speaker with using the supporter hanger and bolt. As shown above A, assemble the a and b of supporter hanger to the monitor with using the bolt(M4x8). Assemble the c, d and e to the speaker with using the bolt(4x16).
Monitor Installation Connecting Speakers to the Monitor using the speakers wires provided R L • Be sure monitor power is turned off before making any connections. Place the speakers in the position you want. Install the speaker wires on the monitor and speaker. Be sure to connect the positive "+" wire to the "+" input and the negative "-" wire to the "-" input. Connect left monitor input to left speaker and right monitor input to right speaker.
Optional Extras Table Stand (Type United) Fixed Wall Mount Bracket Table Stand (Type Separated) Side Mount Speaker OWNER'S MANUAL 25
Watching TV To watch TV (When the Interface board is installed.) 26 1 Connect the Antenna or CATV signal source to TV input. Press TV/VIDEO button on the Remote Control and select TV on OSD. 2 Use CH+, CH- button or numeric button to change TV channel for your channel selection. 3 You can watch the previous channel by pressing PRE CH. Button on Remote Control. 4 Also, you can tune to cable service provided channels using the cable box.
Watching VCR When connecting the Plasma Monitor with external equipment, match the colors of connecting ports (Video yellow, Audio(L) - white, Audio(R) - red). If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor. If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. Avoid having a fixed image remain on the screen for a long period of time.
Watching DVD (Interlace) How to connect (When the Interface board is installed.) Connect DVD video inputs to Y, PB, PR of COMPONENT (480i) (DVD INPUT) and audio inputs to Audio sockets of AV INPUT. How to use (When the Interface board is installed.) 1 Turn on the DVD player. 2 Press TV / Video button on the remote control of the monitor to select Component. Component Input ports You can get better picture quality if you connect DVD player with component input ports as below.
Watching DVD (Progressive) DVD/HDTV Watching through RGB Input for Progressive(480p, 720p, 1080i) mode(YPbPr) How to use (When the Interface board is installed.) 1 Turn on the DVD player or Settop Box. 2 Press TV / Video button on the remote control of the monitor to select Component. (Select "DTV YPbPr") • Normal DVD source is based on 480i, which should be through normal YPbPr of Component signal. • Connect normal 480i, DVD source, through normal YPbPr of Componect signal only.
Connecting The PC You can enjoy vivid picture and sound with connecting a PC with the Monitor. Connecting a PC to the PDP Connect a PC (15pin) cable between the Video Output jack on the PC and the RGB (480p, 720p, 1018i) in (15p D-SUB) on the PDP. Pin Configuration 15Pin Signal Cable (based on mate pin) DVI Cable To see the PC through DVI, Select "Digital RGB" in your OSD. 30 OWNER'S MANUAL Pin No.
Displayable Monitor Specification Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66 37.861 72.80 37.500 75.00 43.269 85.00 45.913 90.03 640 x 350 640 x 400 640 x 480 800 x 600 53.011 100.04 64.062 120.00 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 56.000 90.00 64.016 100.00 832 x 624 49.725 74.55 852 x 480 31.468 60.05 48.363 60.00 56.476 70.
OSD Structure • OSD (On Screen Display) allows user to control or adjust various features and settings in accordance with his/her preferences. • Press the MENU/SET button on the Remote Control, you may see the OSD. e.g.
PICTURE (TV & VIDEO) Adjust Brightness, Contrast, Color, Hue, Sharpness, Temperature and Recall on OSD menu. 1 Press MENU/SET button to activate OSD. 2 Press MENU/SET button again to get into PICTURE main menu. BRIGHTNESS Control the brightness of display by using left and right button. Dark Bright Distinct Vague Decrease Increase CONTRAST Control the contrast of display. COLOR Control the color saturation of display.
PICTURE (TV & VIDEO) SHARPNESS Control the sharpness of image edge. Less sharp Sharp Warm Cold TEMPERATURE Select the color temperature of screen image from Warm, Cool and Normal. RECALL Go into PICTURE Menu, and select Recall then press set for all resets. • Screen Image retention : Do not display a still image (such as on a videogame or when hooking up a PC to this Monitor) on the plasma monitor panel for more than 2 hours as it can cause screen image retention.
PICTURE (PC) Adjust Brightness, Contrast, Temperature and Geometry on OSD menu. 1 Press MENU/SET button to activate OSD. 2 Press MENU/SET button again to get into PICTURE main menu. BRIGHTNESS Control the brightness of display. Dark Bright Distinct Vague Warm Cold CONTRAST Control the contrast of display. TEMPERATURE Select the color temperature of screen image from Warm, Cool and Normal.
PICTURE (PC) GEOMETRY Press MENU/SET button, you can see below picture. Move where you want to adjust. < on Analog RGB mode > H-POSITION Centering display image. After selecting Position menu, you can move the image using VOL -/+ buttons. V-POSITION Centering display image. After selecting Position menu, you can move the image using VOL -/+ buttons. PHASE Fine tuning of display accuracy on the screen. Only available when you are in PC/HD input mode.
SOUND (TV & VIDEO + PC) Adjust the Volume, Balance, Sound Mode and AVC on OSD menu. 1 Press MENU/SET button to activate OSD. 2 Use DOWN button to go to SOUND main menu. 3 Press MENU/SET button again to get into SOUND main menu. VOLUME Control the amount of volume of sound. Ranges from 0 to 100 BALANCE Control the left and right sound balance. SOUND MODE The sound mode feature allows you to choose the best appropriate audio environment.
MISC (TV & VIDEO + PC) Image scaling, OSD display. VIDEO SIZE(Aspect Ratio) You can change the scaling size of video on MISC main menu and VIDEO SIZE sub menu or by pressing V.SIZE button on Remote Control. 16 : 9 Fill the screen regardless of incoming aspect ratio. 4:3 Fit the screen with the same aspect ratio as signal source. Letter Box Expand letter box contents to full screen. But you will notify the display quality worse than original mode due to the loss resolution caused by image expansion.
MISC (TV & VIDEO + PC) Image scaling, OSD display. SET ID If you intend to control more than 2 PDPs via PC, you can assign ID number to each PDP from 1 to 99 by connecting with RS232C cable. ADVANCED You can control the burn protect function. BURN PROTECT Burn protection is to avoid displaying the same image long time. To avoid displaying a static image long time, image moves horizontally 2~3 pixel per 2 minutes. The moving is repeated until PDP set be power-off. (Default Value is "On".
TIME SLEEP : 30 min ➔ 60 min ➔ 90 min ➔ 180 min Select your desirable setting time to turn off the TV automatically. 30 min, 60 min, 90 min, 180 min and "Off" can be selected. The timer will start to count down just after you select. TIME SET You can select the one among Off, Everyday and Once by using Up and Down button.
TV SET-UP MODE Select "Air" or "Cable". If your TV set is connected antenna, select "AIR", If you TV set is connected to the CABLE TV, select "CABLE" AUTO CHANNEL If you select "AUTO CHANNEL" , TV set will automatically scan available channel and add to permanent channel list. If you want to "exit" auto channel scan, press exit key on IR Remote Control. FINE TUNE You can manually adjust the tuning precision by using this function. MTS Select the audio mode on TV broadcasting.
PIP (PC) PIP works in Analog RGB, Digital RGB, and RTV YPbPr mode. PIP(Picture in Picture) ON/OFF Select ON/OFF the PIP mode. You can choose ON/OFF mode using VOL-/+ keys. PIP SOURCE Select the PIP video source. After selecting video source menu, you can change the source using VOL-/+ keys. (TV ➔ AV1 ➔ AV2 ➔ SVIDEO ➔ COMPONENT) AV1 TV AUDIO SOURCE Select the audio source. When you select 'PIP' mode, you will hear PIP audio source. When you select 'Main' mode, you will hear Analog RGB audio source.
Hot Key Function By Remote Control MUTE To turn off the sound. TV / VIDEO Select the signal source from multiple input source of TV, AV1, AV2, S-Video, Component, Analog RGB and DTV YPbPr.(480p, 720p, 1080i input) PIP Activate PIP function on Analog RGB Mode. Fit Aspect CATV 100 CATV3: Mono Still Standard CATV15 L1 Fill Screen AM 11:07 V.SIZE Change the image size setting, ie; 16:9, 4:3, etc. 100 Press this button first for cable channels over 100. PRE CH Go back to previous TV channel.
Hot Key Function By Remote Control Meu/Set Activate the OSD window, enter the sub-menu. CH+/CHChange the TV channel o TV mode up or down. EXIT Exit from the currnet OSD menu or sub-menu. VOL+/VOLChange the audio level, increase or decrease and used for OSD navigation. SOUND The sound mode feature allows you to choose the best appropriate audio environment. ie. Stereo, Mono, Asp. Flat SLEEP TV off time setting, push button for 30 min, 60 min, 90 min and 180 min.
Hot Key Function By Remote Control V-CHIP Push V-Chip button to activate V-Chip function menu. Input 4digit password (factory default password : 0000) And follow the directions. MPAA RATING TV GUIDELINE Select the block level. you can change the ‘SHOW’, ‘BLOCK’ by using VOLUME(¥) keys. Select the TV guideline. you can change the ‘SHOW’, ‘BLOCK’ by using VOLUME(¥) keys. BLOCK CONTENT (TV GUIDELINE CONTENT) PASSWORD CHANGE You can change the ‘SHOW’, ‘BLOCK’ by using VOLUME(¥) keys.
Specification 42" Plasma TV Display Panel Function and Specification 42-inch diagonal screen Variable 4:3 / 16:9 image aspect ratios (4 modes) 16:9 Panoramic mode 853 x 480 physical pixels 1500:1 contrast ratio Brightness : Peak 1000 cd/m 2 PC monitor support up to 1280 x 1024 60hz 181-Program Cable-Ready TV tuner (NTSC) Advanced multi-window viewing : Picture-In Picture(PIP) with four selectable window positions on PC mode Multiple input compatible Advanced Motion digital processor Motion-Adaptive Deinterl
Specification 42" Plasma TV Display Panel Connectivity: Composite : RCA-pin x 1, Scart type x 1 Component video signal : YPbPr x 1(480i/576i) S-video : Mini DIN 4-pin x 1 RGB input : D-sub 15-pin x 1(480p/576p, 720p, 1080i)) Audio input : RCA-pin Type(L/R) x 5 : Full support separated audio input Speaker output : Cinch Conn Type(L/R) x 1(4cinch connectors type) Audio system : Stereo Control Ports : RS-232 D-sub 9-pin x1 DVI Input and DVI Cable / Optional Accessories Full function remote control Table stand
Troubleshooting Before you call a service technician, please scan this list of problems and possible solutions. It may save you time and money. Problem No picture & No sound Quick Action for Possible Solution • Check whether the Monitor is turned on. • Power cord inserted into wall outlet? • Plug another product's power cord into the wall outlet where the Monitor's power cord was plugged in. Picture OK & No sound • Press the VOLUME() button. • Check the audio input signal.
Warranty Card 2-Years Limited Warranty Warranty Service is only available in the country of original purchase. This is an important document. Attach your bill of sale to this card and keep it in a safe place. Your bill of sale is your warranty. Our warranty remains in effect for one year from the date of the first consumer purchase. WHO IS PROTECTED BY THIS WARRANTY Our warranty protects the original owner and all subsequent owners, provided that our product was purchased from an authorized dealer.
Memo 50 OWNER'S MANUAL
Memo OWNER'S MANUAL 51
Memo 52 OWNER'S MANUAL
Manual Version : HMN 1.
