User’s Manual 14221-1600-2100 March 2016 Harris® Bluetooth® Remote Speaker Mic 12082-0800-01
14221-1600-2100 REV DATE - Mar/16 REASON FOR REVISION Initial release. Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization.
14221-1600-2100 TABLE OF CONTENTS Page 1 SAFETY CONVENTIONS .................................................................................................................... 4 2 INTRODUCTION .................................................................................................................................. 5 3 GETTING STARTED ............................................................................................................................ 7 3.1 CHARGE THE BATTERY ............
14221-1600-2100 1 SAFETY CONVENTIONS The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warning elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product. Harris assumes no liability for the customer’s failure to comply with these standards.
14221-1600-2100 2 INTRODUCTION The Harris Bluetooth® Remote Speaker Mic (RSM), 12082-0800, is a wireless device that utilizes Bluetooth® technology. It incorporates a speaker, microphone with push to talk, emergency button, and auxiliary buttons. Support for an audio headset is provided by a 4 pin audio jack, which when used, mutes the RSM speaker. The internal battery is charged using an industry standard micro-USB connector. The rear of the speaker mic includes a clip for attachment to a lapel or belt.
14221-1600-2100 One (1) USB to Micro USB cable 6
14221-1600-2100 3 GETTING STARTED 3.1 CHARGE THE BATTERY The RSM should be charged before first use and after 10-12 hours of use. 1. Power OFF the RSM and connect a micro USB cable to the microphone’s USB port. 2. Connect the USB-A connector to a computer or a wall charger. 3. A SOLID RED light on the RSM indicates charging. The light turns off once the unit is fully charged. Charge time is approximately 2-3 hours. 3.2 POWER ON/OFF Power On: Press and hold the Power button for 3 seconds and release.
14221-1600-2100 3.5.2 Event Indications 3.6 EVENT COLOR PATTERN NOTE Power On Red LED on for 2000 ms - Power Off Red LED on for 2000 ms - SW Reset Red, Red 2 Blinks (1000 ms each) - Link Loss Red, Red, Red 3 Blinks (200 ms each) Repeats on top of Connected state with approximately 15s interval.
14221-1600-2100 BUTTON STATE LENGTH SWB1 Covert Mode Very Long PTT Connectable Short Short Reconnect PTTS Connectable Short Reconnect SWB1+SWB2+PTT+ PTTS Any Very Long SWB1+SWB2 Any Very, Very Long (>10 S) 3.8 ACTION Covert Mode Disable Software Reset, Remove Pairings DFU Mode Enable MICROPHONE PERFORMANCE TIP For best results, do not hold the microphone directly in front of your mouth and do not shout.
14221-1600-2100 3.9.3 Pairing an iPhone with the RSM 1. Turn on the iPhone 2. Turn on the RSM. 3. On the iPhone, navigate to SettingsBluetooth. Enable Bluetooth. 4. The iPhone displays the RSM as “Allcom One PTT.” 5. Tap “Allcom One PTT.” The iPhone indicates that it is now connected to the RSM.
14221-1600-2100 3.9.4 Enable RSM Controls 1. On the iPhone, open the BeOn application. 2. In BeOn, navigate to Menu Preferences Remote Speaker Button Settings and turn on Remote Button Enabled. 3. On the RSM, press the Primary PTT button. The RSM appears under OTHER DEVICES as “Disconnected.” 4. Select the RSM. The RSM appears under SAVED DEVICES as “Connected.
14221-1600-2100 3.9.5 Select the RSM for Audio Output This section describes how to select the RSM as the preferred audio devices for BeOn. In the BeOn app, select MenuAudio OptionAllcom One PTT.
14221-1600-2100 4 OPERATION 4.1 OPERATIONAL PROCEDURES For the Beta version of the RSM, Bluetooth pairing and BeOn audio port selection is maintained between power cycles. However, the first Primary PTT press following the power on cycle of the RSM is used to establish the control connection. For this reason, the first Primary PTT following the power on cycle does not initiate a PTT. All subsequent presses of the PTT buttons initiate a PTT.
221-1600-2100 5 CUSTOMER SERVICE 5.1 CUSTOMER CARE If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative.
