Rear Cover of Manual Front Cover of Manual HDP100 DMR Portable Radio Operator’s Manual 14222-1100-2000 Rev. A, Jul/12 Public Safety and Professional Communications 221 Jefferson Ridge Parkway | Lynchburg, VA USA 24501 www.pspc.harris.
MANUAL REVISION HISTORY REV. DATE REASON FOR CHANGE – Nov/11 A Jul/12 Initial release. Revised attachment procedure for accessory/programming cable and accessory model numbers. Added Equipment and Rechargeable Battery Warranty. Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization.
NOTICE! Information and descriptions contained herein are the property of Harris Corporation. Such information and descriptions may not be copied or reproduced by any means, or disseminated or distributed without the express prior written permission of Harris Corporation, PSPC Business, 221 Jefferson Ridge Parkway, Lynchburg, VA 24501.
TABLE OF CONTENTS Section Page SYMBOLS USED IN THIS MANUAL .................................................................................................................. 1 CAUTION AND NOTE SYMBOLS ................................................................................................................. 1 SYMBOLS FOR ANALOG AND DIGITAL CHANNEL FEATURES/FUNCTIONS ....................................1 REGULATORY INFORMATION ..........................................................................
TABLE OF CONTENTS Section Page LED INDICATOR .......................................................................................................................................... 13 SELECTING A ZONE .................................................................................................................................... 13 SELECTING A CHANNEL ...........................................................................................................................
TABLE OF CONTENTS Section Page EMERGENCY COMMUNICATIONS ............................................................................................................... 22 GENERAL INFORMATION .......................................................................................................................... 22 Emergency Mode ..................................................................................................................................... 22 Emergency Type...........................
TABLE OF CONTENTS Section Page One Touch Call Operation ....................................................................................................................... 34 TELEMETRY ......................................................................................................................................... 34 Supervise a Device via Another/Remote Radio ....................................................................................... 35 Supervise a Device via Third-Party Software .
SYMBOLS USED IN THIS MANUAL The following tables lists symbols used in this manual. CAUTION AND NOTE SYMBOLS SYMBOL DESCRIPTION WARNING The WARNING symbol calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a WARNING symbol until the conditions identified are fully understood or met.
REGULATORY INFORMATION PRODUCT SAFETY BOOKLET WARNING Before operating the HDP100 portable radio, read the safety and RF exposure guidelines contained in Product Safety Booklet included with the radio. RF EXPOSURE GUIDELINES WARNING The HDP100 portable radio generates RF electromagnetic energy during transmit mode.
REGULATORY INFORMATION CAUTION To ensure exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause the FCC RF exposure limits to be exceeded. A proper antenna is the antenna supplied with this radio by Harris or an antenna specifically authorized by Harris for use with this radio.
REGULATORY INFORMATION operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. FCC Part 15 Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
CHECKING ITEMS IN THE PACKAGE Carefully unpack and check that all items listed below are received. If any item is missing or damaged, please immediately contact your dealer. Antenna Operator’s Manual, Product Safety Booklet, Quick Guide Battery Power Adapter Battery Charger Belt Clip Wrist Strap Radio NOTE The antenna may vary with different frequency bands. The frequency band is marked on the label of antenna. If not, refer to the label on the radio unit for frequency band information.
RADIO OVERVIEW RADIO CONTROLS AND OTHER ITEMS ITEM NAME ITEM NAME 1 Side Key 1 (SK1) 8 On/Off/Volume Control Knob 2 PTT Key 9 Microphone 3 Side Key 2 (SK2) 10 Accessory Jack 4 Top Key (TK) 11 Battery Latch 5 Channel Selector Knob 12 Antenna 6 Speaker 13 Belt Clip 7 LED Indicator 14 Battery 6
RADIO OVERVIEW PROGRAMMABLE SHORTCUT KEYS For enhanced convenience, you may request your dealer pre-program keys SK1, SK2, and TK as shortcuts to any of the functions listed in this table: NO. SHORTCUT NAME 1 2 3 4 5 Zone Up Zone Down Adjust Power Level Talk-Around Monitor Monitor Momentary 6 7 8 9 10 Squelch Off Squelch Off Momentary Scan Nuisance Temporary Delete 11 Emergency On 12 Emergency Off SHORTCUT KEY FUNCTION Change to another zone. See page 13.
RADIO OVERVIEW NO. SHORTCUT NAME SHORTCUT KEY FUNCTION 13 Lone Worker Adjust Squelch Level Toggle the Lone Worker feature on and off. See page 27. 14 15 Battery Strength Indicator 16 Man Down (Optional Feature) 17 18 19 20 NOTE 8 Scrambler Encrypt / One Touch Call (1 though 5) Telemetry Roam Temporarily adjust the receiver squelch threshold. See page 18. Indicate remaining battery strength by the LED indicator. See page 18.
BEFORE USING THE RADIO CHARGING THE BATTERY Follow this procedure to charge the radio’s battery: 1. Connect the AC power adapter to an AC power source. See arrow . 2. 3. 4. Plug the small plug of the power adapter into the jack at the rear of the charger. See arrow . Place the radio with the battery attached, or just the battery alone, into the slot in the top of the charger. See arrow . Refer to the following table for charge status, as indicated by the charger’s status indicator.
BEFORE USING THE RADIO ASSEMBLY AND DISASSEMBLY Remove Attaching and Removing the Antenna Attach To attach the antenna to the radio, place its base into the antenna jack on the top of the radio and turn the antenna in a clockwise direction. To remove the antenna from the radio, simply turn the antenna in a counter-clockwise direction until it is free from the radio. Attaching the Battery To attach the battery to the radio: 1.
BEFORE USING THE RADIO Attaching the Belt Clip To attach the belt clip to the radio: 1. Remove the two (2) screws on the rear of the radio. 2. As illustrated, align the screw holes on the belt clip with those on the radio and re-install the two screws into the holes. 3. Using a small screwdriver, tighten the two screws securely. Do not over-tighten them.
BEFORE USING THE RADIO CORRECT ALIGNMENT CAUTION INCORRECT ALIGNMENT INCORRECT ALIGNMENT When an external accessory is attached to the radio’s accessory jack, waterproof performance of the radio may be affected. Removing an Accessory/Programming Cable To remove a cable from the radio’s accessory jack, simply loosen its screw and detach the cable from the jack.
BASIC OPERATIONS TURNING THE RADIO ON AND OFF To turn on the radio, rotate its On/Off Volume Control knob clockwise out of the detent position. A click will be sensed. The radio flashes its LED status indicator green. This knob is item 8 on page 6. To turn the radio off, rotate this knob fully counter-clockwise until the detent click is sensed. ADJUSTING THE VOLUME After turning the radio on, rotate the On/Off Volume Control knob clockwise to increase the volume or counter-clockwise to decrease it.
BASIC OPERATIONS Down shortcut key. When zone 1 is selected, the radio beeps once. When zone 2 is selected, the radio beeps twice. When zone 3 is selected, the radio beeps three times. Keys SK1, SK2, and TK may be pre-programmed by your dealer as Zone Up and Zone Down shortcut keys. The SK1, SK2, and TK keys are illustrated on page 6. SELECTING A CHANNEL The radio’s Channel Selector knob is located on the top of the radio. It is item 5 on page 6.
BASIC OPERATIONS NOTE NOTE Whenever transmitting (i.e., PTT key depressed), hold the front of the radio between 1 to 2 inches from your mouth and speak into the microphone at a normal voice level. This will ensure optimal reception at the receiving radio unit(s). Never shout or whisper when transmitting. As illustrated on page 6, the radio’s microphone is located near the top of the radio. Each digital channel may be pre-programmed with a preset contact by your dealer.
BASIC OPERATIONS Transmitting an All Call When the channel is clear (i.e., when not receiving a signal), hold down the radio’s PTT key to transmit an all call to the All Call contact preset for the currently selected channel. Release the PTT key to stop transmitting, and listen for a reply. All calls can only be transmitted if enabled by your dealer via radio pre-programming. NOTE Receiving an All Call When an all call is received, the call’s audio is heard in the radio’s speaker.
BASIC OPERATIONS 2. 3. 4. Listen for a clear channel. In other words, if another person is using the channel, wait for them to finish transmitting/speaking. If pre-programmed, a monitor or squelch off shortcut key should be used to verify the channel is clear. See the following sections for additional information on these functions. Hold down the radio’s PTT key and speak into the microphone at a normal voice level. Release the PTT key to stop transmitting and listen for a reply.
BASIC OPERATIONS To toggle squelch between enabled and disabled, press the pre-configured Squelch Off shortcut key. To momentarily turn squelch off, depress the pre-configured Squelch Off Momentary key. When this key is released, squelch turns back on. Adjust Squelch Level If programmed, the Adjust Squelch Level shortcut key can be used to select one of three receiver squelch levels: Tight, Normal, and Open.
BASIC OPERATIONS communications with other radios is not possible on the currently selected channel at the low power level, select and use the high power level. Press the programmed Adjust Power Level shortcut key to toggle between the low and high power levels. When switching to the high power level, a high-pitched tone sounds. When switching the low power level, a low-pitched tone sounds. Publication 14222-1100-2000, Rev.
SCANNING CHANNELS GENERAL INFORMATION The radio’s scan feature allows scanning of radio channels pre-programmed into the radio for call activity. Scan lists can be pre-programmed for each channel. Each scan list may contain 32 digital or analog channels. When the radio is scanning channels: • The LED indicator on the top of the radio flashes orange slowly. • The radio scans the channels currently on the scan list for calls (or other activity).
SCANNING CHANNELS speaker. When the Squelch Off function is on or when a call is on the channel, call audio on the channel (or receiver noise) is heard in the radio’s speaker. Press the shortcut key again or the Scan shortcut key to unpause scan. Nuisance Temporary Delete To temporarily remove a channel from a channel’s scan list so calls on it will not pause scanning, press the preprogrammed Nuisance Temporary Delete shortcut key when a call is on the channel.
EMERGENCY COMMUNICATIONS GENERAL INFORMATION The radio’s emergency feature can be used to summon help from another radio operator(s) and/or via a radio dispatch/control center. The emergency process has the highest call priority throughout the radio communications system. Emergency operations can be performed when the radio is transmitting or receiving. The radio can be pre-programmed with different emergency modes, emergency types, and emergency ID types. These are described in the following subsections.
EMERGENCY COMMUNICATIONS Emergency Type The radio supports four (4) emergency types, as defined in the following table. To select a different type, consult with your radio dealer: EMERGENCY TYPE DESCRIPTION Siren Only Regular When an emergency occurs, the radio sounds a shrill alarm tone. When an emergency occurs, the radio gives an audible indication. When an emergency occurs, the radio does not give any indication, audible or visual. This type is typically employed in covert operations.
EMERGENCY COMMUNICATIONS Emergency Operations on Analog Channels Alarm Emergency Mode If the radio is pre-programmed for Alarm emergency mode operations on the selected analog channel, press the pre-programmed Emergency shortcut key transmit an alarm. When an alarm is transmitted, the LED indicator on the top of the radio rapidly flashes orange then glows red to indicate the alarm transmission. The radio may also be pre-programmed to sound an audible alarm.
EMERGENCY COMMUNICATIONS The Alarm with Call emergency mode transmission will continue until the pre-programmed number of alarm cycles and voice cycles completes. Alternately, it can be ended early by simply long-pressing the preprogrammed Emergency shortcut key. Call Only Emergency Mode (HDC1200 Signaling Only) If the radio is pre-programmed for Call Only emergency mode operations on the selected analog channel, use this feature as follows: 1. Press the pre-programmed Emergency shortcut key.
EMERGENCY COMMUNICATIONS Emergency Operations on Digital Channels Alarm Emergency Mode If the radio is programmed for Alarm (only) emergency mode operations on the selected digital channel, use this mode as follows: 1. Press the programmed Emergency shortcut key. The LED indicator glows red to indicate the alarm transmission. 2. Once the emergency cycles expire, the radio exits the emergency mode automatically. To exit the emergency mode early, long-press the programmed Emergency shortcut key.
EMERGENCY COMMUNICATIONS Call Only Emergency Mode If the radio is programmed for Call Only emergency mode operations on the selected digital channel, use this mode as follows: 1. Press the programmed Emergency shortcut key. The radio switches to the dedicated/revert channel for the emergency call. 2. If the “Alarm with Call to Follow” feature is enabled, voice audio can be transmitted by speaking into the microphone when the LED indicator glows red. 3.
EMERGENCY COMMUNICATIONS thus starting a new response period of time. The response timer is typically programmed for many minutes or hours (255 minutes maximum), and the reminder timer is typically programmed for several seconds to a minute (255 seconds maximum). If no reaction is taken when the radio begins beeping and the response timer is allowed to expire, the radio automatically enters the programmed emergency mode.
EMERGENCY COMMUNICATIONS 6. To exit the emergency mode, thus ending alarm and voice transmissions early, press the Emergency Off shortcut key. If this shortcut key is not programmed, select another channel or cycle radio power to exit the emergency mode. To disable (i.e., turn off) the Lone Worker feature, press the programmed Lone Worker shortcut key. A lowpitched tone sounds to indicate the feature is disabled.
HDC1200 SIGNALING GENERAL INFORMATION The HDC100 radio supports HDC1200 signaling. This signaling is compatible with MDC1200 signaling. It supports functions such as PTT ID signaling, emergency signaling, and signaling via selective call. These functions are supported in both encode and decode modes. TRANSMISSION (ENCODE) PTT ID Transmission Along with voice audio, the radio can transmit an HDC1200-encoded identification (ID) number on the selected channel with each press of the radio’s PTT key.
SECURE COMMUNICATIONS GENERAL INFORMATION The radio’s Scrambler feature for analog channels can be used to reduce the likelihood of someone “eavesdropping” via analog radio channels. This feature employs analog voice inversion technology. This feature can be enabled and disabled on a per-channel basis. The radio’s Encrypt feature for digital channels can be used to prevent “eavesdropping” via the digital radio channel. This feature employs 256-bit digital AES encryption technology.
MISCELLANEOUS FEATURES CHANNEL BUSY LOCKOUT If enabled via the programming software, this feature can prevent the radio interfering with other transmitting radios on the same channel. If the PTT key is held down while the channel is in use, the radio will keep beeping, alerting of the transmission prohibition. To stop the beeping, release the PTT key. When the channel is free, press and hold down the PTT key to transmit.
MISCELLANEOUS FEATURES RADIO REGISTRATION SERVICE If enabled by your dealer, the radio will automatically register in the system within a certain period after poweron. When registered, the radio can acquire online information about other radios by accessing specific servers within the valid registration period. GPS REVERT If enabled by your dealer, a registered radio will transmit GPS positioning information to the radio system when the system requests it.
MISCELLANEOUS FEATURES Remote Monitor — Use this Remote Monitor command to enable the microphone of a remote Private Call contact’s radio. This can be used to remotely monitor voices and background sounds near the contact radio’s microphone. Radio Enable — Use this Radio Enable command to enable the radio of a remote Private Call contact for normal use. Radio Disable — Use this Radio Disable command to disable the radio of a remote Private Call contact from normal use.
MISCELLANEOUS FEATURES Supervise a Device via Another/Remote Radio If a device is connected to a radio, you can use another/remote radio to supervise the device. All the radios involved should be configured with the Telemetry feature. For example, the dealer enables the Telemetry feature for both Radio A and Radio B, and assigns the Telemetry feature to the SK1 key on Radio A. To supervise the device C, connect it with Radio B, and press the SK1 key on Radio A.
TROUBLESHOOTING AND TECHNICAL ASSISTANCE TROUBLESHOOTING TABLE SYMPTOM POSSIBLE PROBLEMS Battery is dead. Radio will not turn on. Battery is not properly attached to the radio. Battery is defective/bad. Volume is set too low. Antenna is not properly connected to the radio. When receiving, voice audio is weak, erratic, Antenna is damaged or not present. or not present at all. Speaker may be blocked or damaged. On an analog channel, you cannot communicate with others.
TROUBLESHOOTING AND TECHNICAL ASSISTANCE SYMPTOM On an analog channel, irrelevant communications and/or noises are heard. On a digital channel, you cannot communicate with others but there is a receive indication. Noisy communications. Keypad does not operate. GPS cannot determine location/position. POSSIBLE PROBLEMS SOLUTIONS Other radios may be using the same Adjust the squelch and/or consult with your radio frequency. radio dealer as necessary.
TROUBLESHOOTING AND TECHNICAL ASSISTANCE TECHNICAL ASSISTANCE When technical issues arise that cannot be resolved using the troubleshooting table, contact your radio equipment dealer for solution assistance. Also contact your radio equipment dealer for specific information about how the radio is programmed.
CARE AND CLEANING To ensure optimal radio performance as well as a long radio service life, follow these care and cleaning tips: RADIO CARE • Review and follow all precautions described in the radio’s Product Safety Booklet. • Do not hold the radio by its antenna or by a cable connected to its accessory connector. • Do not pierce or scrape the surface of the radio or its accessories. • Always replace the accessory connector’s cover when an accessory cable is not connected to the radio.
MODEL NUMBERS RADIO PACKAGES MODEL NUMBER DESCRIPTION HD-PBV1B HD-PBV1B-MD HD-PBV1B-TXR HD-PBV1B-MDTXR HD-PBU1B HD-PBU1B-MD HD-PBU1B-TXR HD-PBU1B-MDTXR HD-PBU2B HD-PBU2B-MD HD-PBU2B-TXR HD-PBU2B-MDTXR 40 Momentum HDP100 Portable Radio, 136 to 174 MHz, with GPS and Standard Accessories Momentum HDP100 Portable Radio, 136 to 174 MHz, with GPS, Man Down, and Standard Accessories Momentum HDP100 Portable Radio, 136 to 174 MHz, with GPS (radio only) Momentum HDP100 Portable Radio, 136 to 174 MHz, with GPS, Man
MODEL NUMBERS NOTE Standard accessories include one of each item pictured on page 5 (less the radio). Respective part numbers are listed in the tables that follow. Each radio is supplied with one (1) standard antenna, one (1) standard battery, one (1) standard battery charger with power adapter, and various carrying accessories as pictured on page 5.
MODEL NUMBERS BATTERIES AND BATTERY CHARGERS MODEL NUMBER DESCRIPTION HD-PA2V HD-PA2Y HD-CH4D HD-CH4F HD-PS2V HD-PS2T Battery, Lithium-Ion 2000 mAH Battery, Lithium-Ion 2500 mAH Charger, Battery: 1-Bay with Power Adapter Charger, Battery: 6-Bay Power Supply, 6-Unit, Switching Adapter, AC Power, 100 to 240 Vac at 50/60 Hz Input, 12 Vdc Output STANDARD/OPTIONAL Standard Optional Standard Optional Optional Optional CARRYING ACCESSORIES MODEL NUMBER DESCRIPTION HD-HC3M HD-HC3R HD-CL3N 42 Clip, Belt Strap,
MODEL NUMBERS AUDIO ACCESSORIES MODEL NUMBER DESCRIPTION HD-AE6P HD-AE6R HD-AE6S HD-AE6U HD-AE6V HD-AE6W HD-AE6Y HD-AE6Z Earpiece with On-Mic PTT Earpiece with 3-Wire Surveillance Kit D-Earset with In-Line Mic and PTT Earbud with On-Mic PTT Earbud, Receive-Only Speaker-Mic, Waterproof Earpiece, Receive-Only Earpiece, 2-Wire, Wireless Earphone/Neck Publication 14222-1100-2000, Rev.
WARRANTY REGISTRATION AND WARRANTY WARRANTY REGISTRATION Please register this product within ten (10) days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at http://www.pspc.harris.com/Service/WarrantySupport.asp. EQUIPMENT AND RECHARGEABLE BATTERY WARRANTY A.
WARRANTY REGISTRATION AND WARRANTY covered under Paragraph B. To be eligible for no-charge labor, service must be performed at Seller’s location or other Servicer approved by Seller in writing to make the specific repairs at its place of business during normal business hours. Seller shall pay all freight charges relating to the return and shipment of the defective Products and the repaired or replacement Products to and from the Seller designated location.
