Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Appendix M: Client: Harris Corporation Model: XG-75 UHF-L 5W IDs: OWDTR-0070-E/3636B-0070 Standards: FCC Part 90/IC RSS-119 Report #: 2011098 Manual Please refer to the following pages.
Operator’s Manual 14221-1100-2010 Aug/11 XG-75 Series Portable Radios
14221-1100-2010 REV DATE - Aug/11 REASON FOR REVISION Initial release. Harris Corporation, Public Safety and Professional Communications (PSPC) Business continually evaluates its technical publications for completeness, technical accuracy, and organization.
14221-1100-2010 TABLE OF CONTENTS Page 1 SAFETY CONVENTIONS .................................................................................................................... 6 2 SAFETY TRAINING INFORMATION .............................................................................................. 7 2.1 RF EXPOSURE GUIDELINES ................................................................................................... 7 2.2 ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY ..........................
14221-1100-2010 TABLE OF CONTENTS Page 8.7 MODIFY SCAN LIST ............................................................................................................... 28 8.7.1 System Model Radio...................................................................................................... 28 8.7.2 Scan Model Radio ......................................................................................................... 28 8.8 MENU ................................................................
14221-1100-2010 TABLE OF CONTENTS Page 8.25 9 8.24.5 Scan Lockout Mode ....................................................................................................... 45 8.24.6 Data Lockout Mode ....................................................................................................... 46 SELECTIVE SIGNALING (CONVENTIONAL) ..................................................................... 46 8.25.1 Type 99 Operation ..................................................................
14221-1100-2010 1 SAFETY CONVENTIONS The following conventions are used throughout this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warning elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product. Harris Corporation assumes no liability for the customer’s failure to comply with these standards.
14221-1100-2010 2 SAFETY TRAINING INFORMATION WARNING The Harris XG-75 portable radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only,” meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.
14221-1100-2010 • As noted in Table 2-1, ALWAYS keep the device and its antenna AT LEAST 1.6 cm (0.63 inches) from the body and at least 2.5 cm (1.0 inch) from the face when transmitting to ensure FCC RF exposure compliance requirements are not exceeded. However, to provide the best sound quality to the recipients of your transmission, Harris recommends you hold the microphone at least 5 cm (2 inches) from mouth, and slightly off to one side.
14221-1100-2010 2.3 REGULATORY APPROVALS 2.3.1 Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 2.3.2 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s).
14221-1100-2010 3 OPERATING TIPS Antenna location and condition are important when operating a portable radio. Operating the radio in low lying areas or terrain, under power lines or bridges, inside of a vehicle or in a metal framed building can severely reduce the range of the unit. Mountains can also reduce the range of the unit. In areas where transmission or reception is poor, some improvement may be obtained by ensuring that the antenna is vertical.
14221-1100-2010 3.4 AIRCRAFT WARNING 3.5 Always turn off a portable radio before boarding any aircraft! • Use it on the ground only with crew permission. • DO NOT use while in-flight!! ELECTRIC BLASTING CAPS WARNING 3.6 • To prevent accidental detonation of electric blasting caps, DO NOT use two-way radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way Radios" signs posted where electric blasting caps are being used. (OSHA Standard: 1926.
14221-1100-2010 4 BATTERIES The XG-75 series portable radios use rechargeable, recyclable Nickel Metal Hydride (NiMH) or LithiumIon (Li-Ion) batteries. Please read carefully, the battery information provided, to maximize the useful life of each type of battery. 4.1 WARNING Do not disassemble or modify Lithium Ion battery packs. The Lithium Ion battery packs are equipped with built-in safety and protection features.
221-1100-2010 • Discontinue use if the charger is overheating. • Only charge Harris battery packs using a charger approved for use by Harris. • Do not leave batteries in the charger indefinitely. For best results, leave the battery in the charger for two to six hours after the Green Ready LED comes on. Then place the battery pack into service and fully discharge (as indicated by the radio low battery warning) before re-charging.
14221-1100-2010 Figure 4-1: Removing the Battery Pack 4.4.2 Attaching the Battery Pack Make sure the power to the radio is turned off. 1. Align the tabs at each side on the bottom of the battery pack with the slots at the bottom of the battery cavity . 2. Push the top of the battery pack down until the latches click to attach the battery to the radio. 3. Tug gently to verify that the latches are secure and the battery pack is properly attached to the radio.
14221-1100-2010 4.5 BATTERY DISPOSAL In no instance should a battery be incinerated. Disposing of a battery by burning will cause an explosion. CAUTION RECHARGEABLE BATTERY PACK DISPOSAL – The product you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream.
14221-1100-2010 6 OPTIONS AND ACCESSORIES Table 6-1 lists the Options and Accessories tested for use with the XG-75 series portable radios. Refer to the maintenance manual corresponding to the frequency of your XG-75 or to Harris Products and Services Catalog for a complete list of options and accessories, including those items that do not adversely affect the RF energy exposure. WARNING Always use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc).
14221-1100-2010 DESCRIPTION PART NUMBER DROP SHIP AUDIO ACCESSORIES Earphone Kit, Black Earphone Kit, Beige 2-Wire Kit, Palm Mic, Black 2-Wire Kit, Palm Mic, Beige 3-Wire Kit, Mini-Lapel Mic, Black 3-Wire Kit, Mini-Lapel Mic, Beige Explorer Headset with PTT Lightweight Headset Single Speaker with PTT Breeze Headset with PTT Headset, Heavy Duty, N/C Behind-the-Head, with PTT Ranger Headset with PTT Skull Mic with Body PTT and Earcup Headset, Heavy Duty, N/C Over-the-Head, with PTT Throat Mic with Acoustic
14221-1100-2010 7 USER INTERFACE This section describes the primary user interface; the buttons, knob controls, indicators, switch, and display. 7.1 CONTROLS The XG-75 portable radios feature two rotary control knobs, an emergency button, and a dual-position A/B switch located on the top of the radio (Figure 7-1). The Push-To-Talk (PTT) button and two option buttons are located on the side (Figure 7-2) of the radio.
14221-1100-2010 7.1.1 Buttons, Knobs, and Switch The functions of the buttons and knob controls vary depending on mode of operation. The dual position A/B switch is currently software defined only in ECP mode. Primary functions of the button, switch, and knob controls are discussed in general terms in the following. Table 7-1: Buttons, Knobs, and Switch Functions POWER ON/OFF-VOLUME CONTROL KNOB Applies power to the radio and adjusts audio volume.
14221-1100-2010 7.1.2 Keypad The front mounted keypad of the Scan model has six buttons and System model has 15 buttons. Refer to Figure 7-3 and Figure 7-4, respectively. Figure 7-3: Scan Model Front Panel Figure 7-4: System Model Front Panel The primary and secondary functions of each key, where applicable, are described in Table 7-2 and the following section. Table 7-2: XG-75 Front Keypad Functions KEY FUNCTION Primary Function: Accesses the menu.
14221-1100-2010 KEY FUNCTION Primary function: The Status key accesses the status list (0-9) permitting the transmission of a pre-programmed status message to an EDACS or P25 site. Primary function: The Message key accesses the message list (0-9). The Message key permits the transmission of a pre-programmed message to an EDACS or P25 site. Primary function: Deletes selected groups or channels of the currently selected system from the Scan list.
14221-1100-2010 ICON DESCRIPTIONS Steady – transmit at low power. If icon is not visible – transmit at high power. Steady – transmit in encrypt mode. Flashing – receiving an encrypted call. Steady – Indicates the current channel is set up as a Project 25 (P25) channel. Steady – Indicates the current channel is set up as a ProVoice channel. Steady – Indicates the current channel is set up as an analog channel. Animated (rotates clockwise) – scan mode enabled. If icon is not visible – scan is disabled.
14221-1100-2010 7.4 UNIVERSAL DEVICE CONNECTOR The Universal Device Connector (UDC) provides connections for external accessories such as a headset, a speaker-microphone, audio test box, audio test cables, and programming cables. The UDC is located on the right side of the radio, opposite the PTT Button. The UDC facilitates programming and testing the radio. The UDC pins perform different functions depending on the accessory attached to the UDC. Figure 7-7: XG-75 15-Pin Universal Device Connector 7.
14221-1100-2010 7.5.2 Using Noise Cancellation When using the noise cancellation feature, observe the following: • Talk within two (2) inches of primary microphone (see Figure 7-8). • Speak clearly, loudly, and with authority. • If possible, face the noise source when talking into the radio (see Figure 7-8). • Ensure the primary and secondary microphones are not covered. See Section 7.5.4 for more information on the primary and secondary microphones. • In very noisy environments, it is o.k.
14221-1100-2010 8 OPERATION 8.1 TURNING ON THE RADIO 1. Power on the radio by rotating the power on-off/volume knob clockwise. A short alert signal (if enabled through programming) indicates the radio is ready to use. 2. The display shows the last selected system and group or a default system and group (depending on programming). 3. Adjust the power on-off/volume knob to the desired volume level. 4. Select the desired system and group. The display indicates the current system and group names. 5.
14221-1100-2010 MESSAGE 8.3 NAME DESCRIPTION RXEMER Receive Emergency Indicates an emergency call is being received. This message flashes on line two. TXEMER Transmit Emergency Indicates an emergency call has been transmitted on this radio. message will be flashing on line two. VOL=31 Volume Level Indicates the current volume level. The volume level display ranges from OFF (muted) to 40 (loudest). WHC Who Has Called Indicates an individual call has been received, but not responded to.
14221-1100-2010 8.5 SYSTEM SELECTION METHOD 1: From the control knob: If system selection is programmed to the System/Group/Channel control knob, select a system by turning the knob to the desired system number position (1-16). The display registers the new system name on line one. The button can be programmed to provide access to a “2nd bank” of 16 system number positions (17-32).
14221-1100-2010 8.7 MODIFY SCAN LIST 8.7.1 System Model Radio 1. Press to toggle scan off and verify is not displayed. 2. Select group or channel. 3. Press once to remove group or channel from list. 4. Press once to add as a normal group or channel. 5. Press twice to add as a Priority 2 group. 6. Press three times to add as a Priority 1 group. 7. Press to re-start scanning. 8.7.2 Scan Model Radio 1. Press to toggle scan off and verify is not displayed. 2. Select group or channel. 8.
14221-1100-2010 6. Once the desired setting is reached, press to store the value and return to the main display. For menu items that display radio information, pressing or informational displays. Possible menu items are listed in Table 8-2. 8.8.1 will scroll through a list of Menu Item Selection Process An example of the backlight menu item selection process and menu item parameter change is shown in Figure 8-2. 1. Press . The menu mode is entered. 2.
14221-1100-2010 Table 8-2: Menu Item Information FEATURE DISPLAY PARAMETER SETTING COMMENT Keypad Lock Menu Item: KEY LOCK Locked Unlocked Backlight Adjust Menu Item: BACKLGHT Menu Item: CONTRAST Menu Item: TX POWER Menu Item: REVISION SCAN PRIVATE DISP KEY OFF, 1 thru 6 Locks the keypad. To unlock; press and release then within 1 second press the button NOTE: This sequence is also a short cut to locking the keypad. Selects the light level for backlighting.
14221-1100-2010 Table 8-3: Information Display RADIO ID XXXXXXXX LID in EDACS/EA. In CONV it has no meaning. RAM SIZ RAM Size FLSH SIZ Flash Size RF BAND Frequency Band PERS VER Software Version DSP DATE Date DSP code was built. DSP TIME DSP FEAT DSP VER 8.9 Time DSP code was built. The DSP Features supported by the DSP code, in Hexadecimal.
14221-1100-2010 3. *TXEMER* continues to flash until the emergency is cleared. emergency operation. See Section 8.17 for additional will reappear. 4. Press the PTT and 5. Release PTT when the transmission is complete. 8.12 LOCKING/UNLOCKING KEYPAD 1. Press button. 2. Within 1 second, press the button on the side of the radio. 8.13 HIGH/LOW POWER ADJUSTMENT Transmit power adjustment is possible if enabled through programming.
14221-1100-2010 Figure 8-5: Group/Channel Encryption Key Display 8.14.2 Key Zero All cryptographic keys can be zeroed (erased from radio memory) by pressing the button and while still pressing this button, press and hold the button. Press both buttons for 2 seconds. A series of beeps will begin at the start of the 2 second period and then switch to a solid tone after the keys have been zeroed. The display will indicate KEY ZERO.
14221-1100-2010 8.15.1 Turning Scan On and Off 1. Toggle Scan operation on by pressing clockwise to indicate radio is scanning. (Scan model) or 2. Toggle Scan operation off by again pressing disappear. (System model). (Scan model) or icon rotates (System model). will 1. If the radio scans to a group other than the selected group then receives a call on the selected group, the radio will switch to the selected group.
14221-1100-2010 2. Press . The current priority status of the group will be displayed in column 10 of line three for a time-out period. If the group is not part of the scan list, the status will be blank. 3. While the status is displayed, press line three. 4. Press to add the group to the scan list. The a second time to set the group to Priority 2. The icon is displayed on icon is displayed on line three. a third time to set the group to Priority 1. The icon is displayed on line three. The priority 5.
14221-1100-2010 done using the steps above. Deletions done in this manner will not remain deleted if the radio is powered off and then powered on. 8.16 SCANNING TRUNKED SYSTEMS The radio can be programmed using Radio Personality Manager (RPM) with the following System Scan features. Then these features are automatically enabled when the radio is powered on. A key or menu option is also defined to allow the System Scan features to be toggled during radio operation.
14221-1100-2010 8.16.3 ProScan The radio may be programmed for ProScan system scan operation for multi-site applications. ProScan is a multi-site, system-scanning algorithm. ProScan provides the radio with the ability to select a new system for the radio to communicate on, when the selected system drops below a predefined level.
14221-1100-2010 the unit sending the message, or the associated name if the ID number is found in the individual call list. The radio can be programmed to ring when an individual call is received. If enabled, the ring begins five seconds after the caller un-keys and will continue until the PTT button, the button or the individual call mode is entered. The volume of the ring is adjustable through the volume control levels.
14221-1100-2010 8.18.2 Sending an Individual Call 8.18.2.1 Pre-Stored Individual Calls The following procedures describe how to initiate and complete a Pre-Stored Individual Call. System Model Radio 1. To select a pre-stored individual phone number, enter the individual call mode using the or keys. displayed. Then scroll through the list of stored numbers using the key. is turns on, turns off, and the channel 2. Press the PTT button; when the radio is clear to transmit, access tone sounds.
14221-1100-2010 Figure 8-8: Calls Received and Personality Lists The saved call list shows all ten storage locations. If no calls have been received, the saved call list will be empty and the pre-stored list will be available upon entering the individual call mode. When in the saved call list, pressing the key toggles the time stamp on and off. The time stamp indicates how long ago the call was received. When in the pre-stored list pressing the key toggles the Logical Identification (LID) on and off. 8.
14221-1100-2010 NOTE In half-duplex mode, only one person may talk at a time. The radio PTT button needs to be pressed in order to communicate to the individual called and released for the individual called to be heard. 8.19.2.2 Direct Dialing of Phone Calls (System Model Only) 1. If the phone number is not stored in the pre-stored list of phone numbers, but the phone number is known, it can be entered directly from the keypad. Start by pressing the key, then enter the required number from the keypad.
14221-1100-2010 System Model Radio 1. Follow the procedure in Section 8.19.2 to establish a connection to the telephone system or consult the system administrator for the procedure to access a dial tone on the trunked or conventional system. 2. Overdial numbers are transmitted using one of the following methods: METHOD 1: 1. Enter the overdial selection mode by pressing the button. or buttons to scroll through the list of stored numbers. is displayed. 2.
14221-1100-2010 4. Press and hold the key until the display changes indicating that the number has been stored. Repeat steps 1-4 to store additional numbers, to change numbers already stored, or to change the storage location of a number. 8.21 STATUS/MESSAGE OPERATION The Status and Message operations allow for the transmission of a pre-programmed status or a preprogrammed message to an EDACS or P25 site.
14221-1100-2010 2. Press the corresponding pre-programmed 0 through 9 pre-programmed “message” key. If no message has been programmed for the selected number key, the radio will display NO ENTRY. A valid selection will permit the message to appear in the top line of the display and the message ID to appear in the second line of the display for a pre-programmed time. The message selection can be changed by pressing a different message key 0 through 9, or the message operation can be cancelled by pressing .
14221-1100-2010 Additionally, radios may also be programmed for data only operation (no voice calls transmitted or received). 8.24.1 Displays The following will be displayed during the various states of data mode of operation: TX DATA Appears on top line of display when the radio is transmitting a data call. RX DATA Appears on top line of display when the radio is receiving a data call. DATA OFF Appears on top line of display when the radio is in the data disabled state. DATA ON 8.24.
14221-1100-2010 • Press the PTT. • Change a group or system. • Enter Telephone Interconnect mode. • Enter Individual call mode. • Receive a new emergency assignment. • Declare or clear an emergency. • Receive an individual or phone call. • Receive an Agency, Fleet, or System All Call. • Press 8.24.6 (Scan model) or (System model) to toggle Scan on or off. Data Lockout Mode During the voice call scan hang time (pre-programmed) the radio does not receive data calls. 8.
14221-1100-2010 8.25.3 Resetting Type 99 after a Call After decoding a Type 99 call, the radio operates in Monitor mode and all traffic on the channel is audible. If the channel has Channel Guard, only the traffic with the radio's Channel Guard tone will be heard. To reset Type 99 operation, use one of the following methods: • Press the button. • Press the button, if enabled through programming to toggle Type 99 on/off.
14221-1100-2010 9 PREVENTIVE MAINTENANCE 9.1 IMMERSIBLE PREVENTIVE MAINTENANCE XG-75 radios labelled “immersible” (see Figure 9-1) require periodic testing using specialized equipment to verify the radio’s watertight integrity. To recertify the watertight integrity of the XG-75 portable radio, the radio must be inspected by a service center authorized and certified by Harris to perform the necessary tests to verify the watertight integrity.
14221-1100-2010 Table 9-1: Troubleshooting SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION Radio will not turn on. Low battery charge. Change the battery pack to a fully charged pack. No Audio. Speaker volume is muted. Increase the volume level. Poor Audio. User is in a poor coverage area or not on the network. Move to a better coverage area. Radio powers off for no apparent reason. Radio may be experiencing very low voltage. Have the battery checked by an authorized technician.
14221-1100-2010 10 CUSTOMER SERVICE 10.1 CUSTOMER CARE If any part of the system equipment is damaged on arrival, contact the shipper to conduct an inspection and prepare a damage report. Save the shipping container and all packing materials until the inspection and the damage report are completed. In addition, contact the Customer Care center to make arrangements for replacement equipment. Do not return any part of the shipment until you receive detailed instructions from a Harris representative.
14221-1100-2010 RECHARGEABLE BATTERY WARRANTY A. Harris Corporation, a Delaware Corporation, through its RF Communications Division (hereinafter "Seller") warrants to the original purchaser for use (hereinafter "Buyer") that nickel-cadmium, nickel-metal hydride, lithium-ion, and lithiumpolymer batteries supplied by Seller shall be free from defects in material and workmanship, and shall conform to its published specifications for a period of twelve (12) months from the date of purchase. B.
14221-1100-2010 WARRANTY Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at http://www.pspc.harris.com/Service/WarrantySupport.asp A. B. C. D. E.
Public Safety and Professional Communications | www.pspc.harris.
Product Safety Manual 14221-1100-2020 Aug/11 This booklet contains important safety information regarding specific absorption rate (SAR) and RF exposure limits included in United States and international standards. Read the information in this booklet before operating your radio.
REV - DATE Aug/11 DESCRIPTION Initial release ACKNOWLEDGEMENTS The software contained in this device is copyrighted by Harris Corporation. Unpublished rights are reserved under the copyright laws of the United States.
TABLE OF CONTENTS Page 1. 2. 2.1 2.2 2.3 3. 4. 4.1 4.2 5. 6. 6.1 6.2 6.3 6.4 7. 8. 9. SAFETY SYMBOL CONVENTIONS ........................................... 4 SAFETY TRAINING INFORMATION ........................................ 5 RF EXPOSURE GUIDELINES...................................................... 5 ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY .... 6 REGULATORY APPROVALS ..................................................... 7 OPERATING TIPS .............................................................
1. SAFETY SYMBOL CONVENTIONS The following conventions are used to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere violates safety standards of design, manufacture, and intended use of the product. Harris Corporation assumes no liability for the customer's failure to comply with these standards.
2. SAFETY TRAINING INFORMATION WARNING The Harris Corporation XG-75 portable radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only,” meaning it must be used only during the course of employment by individuals aware of the hazards and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment.
• ALWAYS transmit using low power when possible. In addition to conserving battery charge, low power can reduce RF exposure. • ALWAYS use Harris authorized accessories (antennas, batteries, belt clips, speaker/mics, etc). Use of unauthorized accessories may cause the FCC Occupational/Controlled Exposure RF compliance requirements to be exceeded. • As noted in Table 2-1, ALWAYS keep the device and its antenna AT LEAST 1.6 cm (0.63 inches) from the body and at least 2.5 cm (1.
2.3 REGULATORY APPROVALS 2.3.1 Part 15 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 2.3.2 Industry Canada This device complies with Industry Canada license-exempt RSS standard(s).
4. EFFICIENT RADIO OPERATION Keep the antenna in a vertical position when receiving or transmitting a message. Do NOT hold onto the antenna when the radio is powered on. WARNING 4.1 ANTENNA CARE AND REPLACEMENT WARNING WARNING WARNING 4.2 Always keep the antenna at least 0.43 inches (1.1 cm) away from the body and 1.0 inch (2.5 cm) from the face when transmitting to ensure FCC RF exposure compliance requirements are not exceeded. Do not use the portable radio with a damaged or missing antenna.
4.2.2 Electric Blasting Caps WARNING To prevent accidental detonation of electric blasting caps, DO NOT use two-way radios within 1000 feet of blasting operations. Always obey the "Turn Off Two-Way Radios" signs posted where electric blasting caps are being used. (OSHA Standard: 1926.900) 4.2.3 Potentially Explosive Atmospheres Areas with potentially explosive atmospheres are often, but not always, clearly marked.
6. BATTERY PACKS The XG-75 series portable radios use rechargeable, recyclable Nickel Metal Hydride (NiMH) and Lithium Ion (Li-Ion) battery packs. Please follow the directions below to maximize the useful life of each type of battery pack. WARNING WARNING 6.1 Do not disassemble or modify Lithium Ion battery packs. The Lithium Ion battery packs are equipped with built-in safety and protection features.
6.4 BATTERY DISPOSAL In no instance should a battery pack be incinerated. Disposing of a battery pack by burning will cause an explosion. CAUTION RECHARGEABLE BATTERY PACK DISPOSAL – The product you have purchased contains a rechargeable battery pack. The battery pack is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery pack into the municipal waste stream.
8. TECHNICAL ASSISTANCE The Technical Assistance Center's (TAC’s) resources are available to help with overall system operation, maintenance, upgrades and product support. TAC is your point of contact when answers are needed to technical questions. Product specialists, with detailed knowledge of product operation, maintenance, and repair, provide technical support via a toll-free (in North America) telephone number. Support is also available through mail, fax and e-mail.
RECHARGEABLE BATTERY WARRANTY A. Harris Corporation, a Delaware Corporation, through its RF Communications Division (hereinafter "Seller") warrants to the original purchaser for use (hereinafter "Buyer") that nickel-cadmium, nickelmetal hydride, lithium-ion, and lithium-polymer batteries supplied by Seller shall be free from defects in material and workmanship, and shall conform to its published specifications for a period of twelve (12) months from the date of purchase. B.
WARRANTY A. Harris Corporation, a Delaware Corporation, through its RF Communications Division (hereinafter "Seller") warrants to the original purchaser for use (hereinafter "Buyer") that Equipment manufactured by or for the Seller shall be free from defects in material and workmanship, and shall conform to its published specifications. With respect to all nonSeller Equipment, Seller gives no warranty, and only the warranty, if any, given by the manufacturer shall apply.
NOTES 14221-1100-2020 15
