Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Appendix L: Client: Harris Corporation Model: SG5300-800 ID’s: OWDTR-0063-E/3636B-0063 Standards: FCC Part 90 Report #: 2011065 Manual Please refer to the following pages.
Product Manual MM-018623-001 Jul/11 SG5300 Data Modem 800 MHz and 900 MHz
MM-018623-001 MANUAL REVISION HISTORY REV DATE - Jul/11 REASON FOR CHANGE Initial release. CREDITS Harris, assuredcommunications, EDACS, and OpenSky are registered trademarks and NetworkFirst is a trademark of Harris Corporation. Conxall and Multi-Con-X are registered trademarks of Conxall Inc. Band-it is a registered trademark of BAND-IT-IDEX, Inc. A Unit of IDEX Corporation All other brand and product names are trademarks, registered trademarks, or service marks of their respective owners.
MM-018623-001 SOFTWARE LICENSE AGREEMENT THE SOFTWARE PROGRAM PROVIDED WITH THIS DOCUMENT IS FURNISHED UNDER A LICENSE AND MAY BE USED ONLY IN ACCORDANCE WITH THE FOLLOWING LICENSE TERMS.
MM-018623-001 TABLE OF CONTENTS Section 4 Page 1 REGULATORY AND SAFETY INFORMATION .................................................................... 7 1.1 REGULATORY APPROVALS ............................................................................................ 7 1.1.1 Transmitter ............................................................................................................... 7 1.1.2 Receiver .......................................................................................
MM-018623-001 TABLE OF CONTENTS Section 8.1 8.2 8.3 9 Page DOWNLOAD SOFTWARE ............................................................................................... 31 8.1.1 Set Server IP Address ............................................................................................. 31 8.1.2 Install Software....................................................................................................... 31 CONFIGURATION ..............................................................
MM-018623-001 LIST OF FIGURES Page Figure 3-1: Figure 3-2: Figure 3-3: Figure 4-1: Figure 6-1: Figure 8-1: Figure 8-2: Figure 8-3: SG5300 Data Modem ....................................................................................................... 12 SG5300 System Application............................................................................................. 13 DNP3 Protocol Example...................................................................................................
MM-018623-001 1 REGULATORY AND SAFETY INFORMATION 1.1 REGULATORY APPROVALS 1.1.1 Transmitter The transmitting devices listed below have been tested and meet the following regulatory requirements: MODEL DESCRIPTION FCC ID (PART 90) INDUSTRY CANADA (RSS-119) SG5300-800 RU-019026-800 Radio Unit OWDTR-0063-E 3636B-0063 SG5300-900 RU-019026-900 Radio Unit OWDTR-0064-E 3636B-0064 1.1.
MM-018623-001 1.2 SAFETY SYMBOL CONVENTIONS The following conventions may be used in this manual to alert the user to general safety precautions that must be observed during all phases of operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the product. Harris Corporation assumes no liability for the customer's failure to comply with these standards.
MM-018623-001 1.3 RF ENERGY EXPOSURE INFORMATION To ensure that exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: CAUTION • DO NOT operate the SG5300 without a proper antenna attached, as this may damage the SG5300 and may also cause the FCC RF exposure limits to be exceeded.
MM-018623-001 Table 1-1: MPE Table 900 MHz 800 MHz Antenna Safe Distance, Rsafe, (cm) Controlled Uncontrolled Environment Environment AN-225001-001 3 dBd (5.15 dBi) dual band roof mount antenna AN-225001-002 3 dBd (5.15 dBi) dual band elevated feed point antenna AN-225001-003 3 dBd (5.15 dBi) dual band elevated feed point antenna 20 20 20 20 20 20 AN-225001-004 2 dBd (4.15 dBi) low profile antenna 20 25 AN-225001-005 5 dBd (7.15 dBi) dual band roof mount 20 20 AN-225005-001 3 dBd (5.
MM-018623-001 2 INTRODUCTION 2.1 ABOUT THIS MANUAL This manual is written for the communications professional responsible for installing and maintaining the SG5300 Data Modem. 2.2 GLOSSARY OF TERMS The following Table is a list of terms used in this manual.
MM-018623-001 3 DESCRIPTION The SG5300 Data Modem is part of the OpenSky® suite of products which delivers very high capacity, end-to-end digital data communication. The small and lightweight unit is housed in a plastic case for mounting indoors or in a NEMA enclosure and is designed to provide reliable, secure, and cost effective data communications to and from remote locations. Figure 3-1: SG5300 Data Modem 3.1 MULTIPLE APPLICATIONS The SG5300 is suitable for a wide range of applications.
MM-018623-001 Figure 3-2: SG5300 System Application The SG5300 provides a choice of Ethernet (RJ45) or Serial (DB9) interface to remote terminals. Its 3Watt RF output makes it a compact and cost-effective wireless link that can easily fit alongside Remote Terminal Units (RTUs) and other devices. The SG5300 is capable of interfacing to RTUs via an Ethernet 10/100Base-T interface port or TIA/EIA232 Serial interface port.
MM-018623-001 3.3 VERSATILE MOUNTING The SG5300 is designed to be mounted indoors or in a NEMA enclosure. 3.4 DNP3 A common protocol used between the System Server and RTUs is DNP3. DNP3 (Distributed Network Protocol) is intended for communications between RTU, IED, and controller devices in SCADA networks. It is a more general protocol than IEC 60870-5-104 and is used in the electrical distribution, water infrastructure, oil and gas, waste water, and security industries.
MM-018623-001 4 OPERATION In-service operation of the SG5300 is completely automatic. Once the unit is properly installed and configured, local unit operation can be observed by viewing the Status LEDs for proper operation. After properly installing the unit, operational control and monitoring can be made from the Network Management Center and the Centralized System Server. 4.1 STARTING SG5300 Start the radio operation by following these steps: 1. Apply DC power to the transceiver. 2.
MM-018623-001 4.2 INDICATORS The SG5300 RF Radio unit has two tri-color LEDs which indicate its operating status. The Unit Status LED, located near the power connector, indicates Power On or Normal Operation (amber or orange). It also indicates when the unit is in the Configure Ethernet mode (red) or is booting up (green). The Radio Status LED, located near the antenna connector, indicates the operational status of the radio section.
MM-018623-001 5 UNPACKING AND CHECKING EQUIPMENT Before unpacking, installing, or operating the SG5300, read this section of the manual thoroughly. It contains detailed unpacking and handling instructions, and safety precautions to protect users and equipment. 5.1 UNPACKING EQUIPMENT The SG5300 may be shipped in separate transit packages. The associated cabling and accessories for each unit, if any, may also be shipped in separate containers.
MM-018623-001 5.
MM-018623-001 6 INSTALLATION 6.1 GENERAL PLANNING Careful planning and preparation of any installation will always benefit the end result. 1. Always read and follow all installation instructions, local and national building and electrical codes, and general safety rules. 2. Before beginning the installation, collect information from the Site Deployment Order (SDO) specific to the site access such as: • Permission to access the site. • Important contact names and telephone numbers.
MM-018623-001 6.3 EQUIPMENT INSTALLATION Below are the basic steps for installing the SG5300. In most cases, these steps alone are sufficient to complete the installation. Each step references more detailed instructions contained in this manual. 1. Mount the SG5300 to a stable surface. Refer to Section 6.4 for dimensions. 2. Connect the RTU equipment to the appropriate data interface connector. (See Section 6.5.3 for Ethernet interface or 6.5.4 for a serial interface.
MM-018623-001 Unit: mm Figure 6-1: SG5300 Physical Dimensions 21
MM-018623-001 6.5 CONNECTIONS CONNECTION 6.5.1 DESCRIPTION Input Power: WAGO, 2-pin connector for DC Power (9 to 57 VDC) Ethernet Interface: Ethernet connector (RJ-45) Serial Interface: Serial RS-232 connector (DB-9F) Antenna: RF connector (TNC-F) Power Connections The SG5300 is compatible with any well-filtered 9.0 to 57 VDC power source. Exceeding the maximum input voltage of 57 Volts may cause permanent damage to the equipment.
MM-018623-001 1. Route the power cable between the SG5300 and the power source. 2. At the SG5300, strip off 5/16-inch (8-9 mm) of insulation from each wire. 3. Using a small flat-head screwdriver, insert the screwdriver blade into the power connector release port to open the spring clamp. 4. Insert the stripped wire end into the power connector wire opening. 5. Remove the screwdriver and the spring clamp will secure the wire. This can be verified by gently tugging in the wire. 6.
MM-018623-001 6.5.3 Ethernet Data Interface Connection The SG5300 Ethernet interface is used for connecting to an RTU. The unit’s Ethernet Interface meets the following requirements: • Connector Type: RJ-45 Receptacle • Electrical Protocol: 10/100Base-T • Data Rate: 10/100 Mbps • Data Format: Ethernet IEEE 802.
MM-018623-001 6.5.4 Serial Data Interface Connection The SG5300 serial interface is used for Serial Line Internet Protocol (SLIP) or Point to Point Protocol (PPP) data as well as for unit configuration and maintenance support. The serial interface can be configured to operate as a full duplex DCE EIA/TIA-232 port and meets the following requirements: • Connector Type: DB-9F Receptacle • Mating Part Number: DEMM9 Plug • Electrical Protocol: EIA/TIA-232 Full Duplex • Data Rate: 9.
MM-018623-001 Table 6-4: Surge Protection Options PART NUMBER 26 DESCRIPTION PT-016508-002 RF Surge Protector, Coax, TNC. PT-016508-003 Cat5e, RJ-45, Data Port Surge Protector. PT-016508-005 Surge Protector, DC, Wire, 54 Vdc.
MM-018623-001 7 CONFIGURATION Configuration of the SG5300 is performed with an external computer attached to the DB9 serial port. Your Network Administrator should configure the SG5300. Changes to the configuration, if required, can also be made over-the-air if this option has been purchased. There are three primary considerations when setting up an SG5300. These include configuration and software loading of either the RF Radio or the Ethernet port. 7.1 EQUIPMENT REQUIRED Service PC 7.
MM-018623-001 Commands: Description: at@ar1 Auto Reg where 1=enable, 0=disable. at\u xxx.xxx.xxx.xxx Service IP Address (xxx.xxx.xxx.xxx). at\p x Service Port number. at\s yyy.yyy.yyy.yyy Radio IP Address (yyy.yyy.yyy.yyy). at\b zzz.zzz.zzz.zzz Broadcast IP Address (zzz.zzz.zzz.zzz). at@c x,x,x,x Loads Band, Chan#1, Chan#2, RF Protocol.
MM-018623-001 7.3 CONFIGURING THE ETHERNET PORT To configure the SG5300 Ethernet port through a serial connection between a console terminal or PC and the SG5300’s Serial port: 1. Connect a console terminal or PC running a terminal emulation program (i.e. HyperTerminal) to your unit’s serial port. The default serial port settings are 9600 baud, 8 bits, no parity, 1-stop bit, noflow control. 2. Toggle the SG5300’s Configuration Switch from and to the Config-Ethernet position.
MM-018623-001 IP Address : (0) xxx.(0) xxx.(0) xxx.(0) xxx Set Gateway IP Address (N) ? Netmask: Number of Bits for Host Part (0=default) (8) Change telnet config password (N) ? 6. From the Change Setup menu, enter 1 for Channel 1 configuration after “Your choice ?” and press the Enter key. 7. Set the entry fields as shown below where the Local Serial IP address xxx.xxx.xxx.xxx is replaced with the previously set SG5300 Ethernet port IP address and the Peer Serial IP address yyy.yyy.yyy.
MM-018623-001 8 SOFTWARE INSTALLATION This section provides instructions for installing software in the SG5300. 8.1 DOWNLOAD SOFTWARE 8.1.1 Set Server IP Address 1. Connect the SG5300 to the PC serial port. If working with a DTE device a null modem cable or adapter will be required. 2. Place SG5300 serial interface selector switch in the Config Ethernet position. 3. Connect power to the device being configured while depressing the “x” key (must be lower case). 4.
MM-018623-001 7. When the following menu appears: Change Setup: 0 1 5 6 7 8 9 Server configuration Channel 1 configuration Expert Security factory defaults exit without save save and exit Your choice ? 8. Enter “9” to exit configuration mode and start normal operation. 9. Connect the Ethernet port of the slip converter to the Ethernet port of the PC containing the FTP server and code for the device being configured. 10. Set the TFTP PC’s IP address to 192.168.1.5. 11.
MM-018623-001 3. Press the Enter key to enter Setup Mode. The following message appears: Change Setup: 0 1 5 6 7 8 9 Server configuration Channel 1 configuration Expert Security factory defaults exit without save save and exit Your choice ? 4. Enter “0” followed by the enter key. 5. When prompted for an IP Address: enter the desired IP address of the Ethernet server port (i.e., 192.168.1.254), placing a period between the octets or press the Enter key to move to the next octet. 6.
MM-018623-001 4. When prompted for the “Flow (00) ?”: Press the Enter key. 5. When prompted for to “Enable passive mode (N) ?”: Press the Enter key. 6. When prompted for the “Enable bridge mode (N) ?”: Press the Enter key. 7. When prompted for the “Local Serial IP address”: Enter the desired IP address of the local serial port (i.e., 10.248.15.85 ), placing a period between the octets or press the Enter key to move to the next octet. 8.
MM-018623-001 18. When prompted for the “Map Cloud TCP, UDP or ICMP to Ethernet IP & Port T(CP) or U(DP) or (I)CMP”: Enter: • I for ICMP traffic • U for UDP traffic • T for TCP traffic 19. When prompted for the “Cloud Port #: (0) ?”: Enter the port number that was assigned at the source of the message i.e., (telnet port 23, HTTP port 80). 20. When prompted for the”Tto Port #: (0) ?”: Enter the port number that the destinstion application will want to see.
MM-018623-001 IP addr 192.168.1.254, no gateway set,netmask 255.255.255.0 *** Security SNMP is enabled SNMP Community Name: public Telnet Setup is enabled TFTP Download is enabled Port 77FEh is enabled Web Server is enabled Web Setup is enabled ECHO is disabled Enhanced Password is disabled ***************** Channel 1 ***************** Baudrate 19200, I/F Mode 4C, Flow 00 CPU performance : Standard Local Serial IP address 10.0.0.2 Peer Serial IP address 10.0.0.1 NAT IP address 0.0.0.
MM-018623-001 Change Setup: 0 Server configuration 1 Channel 1 configuration 5 Expert 6 Security 7 factory defaults 8 exit without save 9 save and exit Your choice ? 8.2.3 Load Factory Defaults 1. When the following menu appears, enter “7” followed by the Enter key. Change Setup: 0 1 5 6 7 8 9 Server configuration Channel 1 configuration Expert Security factory defaults exit without save save and exit Your choice ? 2.
MM-018623-001 ***************** Channel 1 ***************** Baudrate 9600, I/F Mode 4C, Flow 00 CPU performance : Standard Local Serial IP address 255.255.255.255 Peer Serial IP address 255.255.255.255 NAT IP address 255.255.255.255 DNS Server IP address 255.255.255.255 Passive Mode: enabled Bridge Mode: enabled Allow broadcasts: enabled Monitor Connection Control: enabled SLIP Client Mode: enabled Static Map Table PROTO [Cloud Socket] [Ethernet Socket] 01: --- 000.000.000.000:00000 <-> 000.000.000.
MM-018623-001 2. If this is to be a new installation, select menu option “7” followed by menu option “9.” If you selected menu option “7,” you will get the following configuration the next time you connect to the SG5300: • An address for the server port has been set to 192.168.1.254 with a subnet mask of 255.255.255.0. • The serial ports have been assigned along with basic static table entries. *** basic parameters Hardware: Ethernet TPI IP addr 192.168.1.254, no gateway set,netmask 255.255.255.
MM-018623-001 12: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 13: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 14: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 *** Expert CPU performance: Regular Monitor Mode @ bootup : enabled MTU Size: 1400 Alternate MAC: disabled Ethernet connection type: auto-negotiate Change Setup: 0 Server configuration 1 Channel 1 configuration 5 Expert 6 Security 7 factory defaults 8 exit without save 9 save and exit Your choice ? 8.3.
MM-018623-001 4. Assign static entries into the translation table to allow UDP and ICMP traffic (Menu Selection 1 table entry). When you have completed your configuration entries, your configuration will look like the following: *** basic parameters Hardware: Ethernet TPI IP addr 10.248.15.10, no gateway set,netmask 255.255.255.
MM-018623-001 13: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 14: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 *** Expert CPU performance: Regular Monitor Mode @ bootup : enabled MTU Size: 1400 Alternate MAC: disabled Ethernet connection type: auto-negotiate 5. Select menu item “9” to save your configuration and exit. 8.3.2 Sample Implementation, SG5300 and Two Logical Networks This is a sample implementation for a single device and two (2) logical networks.
MM-018623-001 *** Security SNMP is enabled SNMP Community Name: public Telnet Setup is enabled TFTP Download is enabled Port 77FEh is enabled Web Server is enabled Web Setup is enabled ECHO is disabled Enhanced Password is disabled ***************** Channel 1 ***************** Baudrate 19200, I/F Mode 4C, Flow 00 CPU performance : Standard Local Serial IP address 10.248.15.10 Peer Serial IP address 10.248.15.9 NAT IP address 0.0.0.0 NAT IP address offset 16 DNS Server IP address 0.0.0.
MM-018623-001 MTU Size: 1400 Alternate MAC: disabled Ethernet connection type: auto-negotiate 6. Select menu item “9” to save your configuration and exit. 8.3.3 Sample Implementation, SG5300, 2 logical networks, and Multiple Devices This is a sample implementation for multiple devices and two (2) logical networks. Figure 8-3: SG5300, Two Logical Networks, and Multiple Devices In this example, the application server will need to maintain a static table that it associates the 192.x.x.
MM-018623-001 4. Assign static entries into the translation table to allow UDP and ICMP traffic (Menu Selection 1 table entry). 5. When you have completed your configuration entries, you configuration will look like the following data: *** basic parameters Hardware: Ethernet TPI IP addr 192.168.1.254, no gateway set,netmask 255.255.255.
MM-018623-001 10: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 11: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 12: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 13: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 14: --- 000.000.000.000:00000 <-> 000.000.000.000:00000 *** Expert CPU performance: Regular Monitor Mode @ bootup : enabled MTU Size: 1400 Alternate MAC: disabled Ethernet connection type: auto-negotiate 6. Select menu item “9” to save your configuration and exit.
MM-018623-001 9 TROUBLESHOOTING AND SERVICING There are no user serviceable components within the SG5300 assembly. This assembly contains ESD sensitive components and should only be serviced by Harris qualified personnel. 9.1 TROUBLESHOOTING If a unit is suspected to be faulty or need service and repair, perform the following checks: 9.2 • Visually inspect the installation for obvious defects such as worn, weathered, or frayed cabling.
MM-018623-001 10 CUSTOMER SERVICE 10.1 TECHNICAL ASSISTANCE The Technical Assistance Center's (TAC) resources are available to help with overall system operation, maintenance, upgrades, and product support. TAC is the point of contact when answers are needed to technical questions. Product specialists, with detailed knowledge of product operation, maintenance, and repair provide technical support via a toll-free (in North America) telephone number. Support is also available through mail, fax, and e-mail.
MM-018623-001 11 SPECIFICATIONS 11.1 GENERAL SPECIFICATIONS Model Number: SG5300-800 (RU-019026-800) SG5300-900 (RU-019026-900) Physical Characteristics: Electrical Power: Power Consumption: +9 to +57 Vdc 9.6 Watt Transmit 2.5 Watt Receive <3 Watt Average Power at 95/5 Size (H x W x D): 1.5 × 3.9 × 7.8 in (3.9 × 10.0 × 19.8 cm) Weight: 1.6 lbs (0.
MM-018623-001 11.2 TRANSMITTER SPECIFICATIONS Typical performance specifications 800 MHz 900 MHz Frequency Range (MHz): 806-809 / 809-824 896-901 / 935-940 Rated RF Power Trunked (W): 0.5-3 0.5-3 Frequency Stability (-30 to +60°C; +25°C Ref) (ppm): ±1.5 / ±2.5 ±1.5 Modulation Deviation (kHz): ±3.75 / ±4.0 ±1.8 11.
MM-018623-001 12 WARRANTY Please register this product within 10 days of purchase. Registration validates the warranty coverage, and enables Harris to contact you in case of any safety notifications issued for this product. Registration can be made on-line at http://www.pspc.harris.com/Service/WarrantySupport.asp. A.
Public Safety and Professional Communications | www.pspc.harris.
