User Manual
Table Of Contents
- 1 REGULATORY AND SAFETY INFORMATION
- 1.1 SAFETY SYMBOL CONVENTIONS
- 1.2 RF ENERGY EXPOSURE AWARENESS AND CONTROL INFORMATION FOR FCC OCCUPATIONAL USE REQUIREMENTS
- 1.3 COMPLIANCE WITH RF EXPOSURE STANDARDS
- OCCUPATIONAL SAFETY GUIDELINES AND SAFETY TRAINING INFORMATION
- 1.5 COMMON HAZARDS
- 1.6 SAFE DRIVING RECOMMENDATIONS
- 1.7 OPERATING RULES AND REGULATIONS
- 1.8 OPERATING TIPS
- 2 Marine Frequencies
- 3 SPECIFICATIONS
- 4 INTRODUCTION
- 5 UNPACKING AND CHECKING THE EQUIPMENT
- 6 PLANNING THE INSTALLATION
- 7 ANTENNA INSTALLATION
- 7.1 ANTENNA MOUNTING LOCATIONS
- 7.2 ANTENNA INSTALLATION PROCEDURES
- 7.2.1 Installing NMO Antenna Mounts AN125001-001, 002, 003 and 004
- 7.2.2 Installing NMO Magnetic Antenna Mounts AN125001-007 and AN125001-008
- 7.2.3 Installing All Other Antenna Mounts
- 7.2.4 Attaching NMO Antenna Elements
- 7.2.5 Installing the Coax Cable and TNC RF Connector
- 7.2.6 Install GPS Antenna (Required Only if Radio has GPS Receiver Option)
- 8 FRONT-MOUNT RADIO INSTALLATION
- 9 REMOTE-MOUNT RADIO INSTALLATION
- 9.1 MOUNTING THE REMOTE-MOUNT RADIO
- 9.2 REMOTE-MOUNT RADIO’S DC POWER INSTALLATION
- 9.3 CH721 CONTROL HEAD INSTALLATION
- 9.4 HHC731 HAND-HELD CONTROLLER INSTALLATION
- 9.4.1 Mounting the HHC731 Interface Cable and Bracket
- 9.4.2 Connecting CAN Link
- 9.4.3 Connecting DC Power
- 9.4.4 Mounting the HHC731 Hanger
- 9.4.5 Connecting the HHC731 to the HHC731 Interface Cable
- 9.4.6 Connecting a Siren/Light Control System
- 9.4.7 Connecting a Headset
- 10 SPEAKER INSTALLATION
- 11 MICROPHONE ATTACHMENT
- 12 OPTIONAL CABLES
- 12.1 M5300/M7300 OPTION CABLE CA-012349-001
- 12.2 CH721 OPTION CABLE CA011854001
- 12.3 ACCESSORY CABLE 19B802554P24
- 12.4 HHC731 INTERFACE CABLE CA018399001
- 12.5 SERIAL DATA CABLE CA013671020
- 12.6 CH721 SERIAL PROGRAMMING CABLE CA104861
- 12.7 CH721 MIC CONNECTOR PROGRAMMING CABLE CA103541001
- 12.8 SPEAKER-ONLY OPTION CABLE CA012349-007
- 13 GPS NMEA-FORMATTED DATA CONNECTION
- 14 MOBILE DATA CONNECTION
- 15 INITIAL POWER-UP TEST
- 16 PERFORMANCE TESTS
- 17 COMPLETE THE INSTALLATION
- 18 WARRANTY REGISTRATION
- 19 WARRANTY
MM-014763-001, Rev. G
102
12.4 HHC-731 INTERFACE CABLE CA-018399-001
HHC-731 Interface Cable CA-018399-001 interconnects a DC power cable and the CAN cable from the
radio to the HHC-731 hand-held controller. It also has a 25-pin connector that can be used to connect
optional equipment to the HHC-731. The cable’s assembly and wiring diagrams are shown in Figure 12-4
below. Connector J1 mates with the DC power cable from the main and switched fused power sources.
Connector J3 mates with the CAN cable from the radio. Connector P2 (male DB-25) mates to the coiled
cord of the CH-721 hand-held controller. Connector P3 (female DB-25) is the connector for optional
connections, such an external siren and light system (e.g., Federal Signal SS2000 SmartSiren
®
). Refer to
Section 9.4 in this manual for installation instructions.
(Made From PS-CA-018399 Sh. 1 and 3, Rev. A)
Figure 12-4: HHC-731 Interface Cable CA-018399-001
FEMALE
PARTIAL SIDE VIE W PARTIAL SIDE VIE W
REAR VIEW
WIRING DIAGRAM